Search Documents

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By D. W. McDonald, N. A. Duke, R. L. Hauser

"Abstract- The NERCO Con Mine is situated in the amphibolite facies aureole of the Western Plutonic Complex overprinting the Yellowknife Greenstone Belt. Metamorphic grade of the upright monoclinal basaltic succession decreases from hornblende-amphibolite facies along the border of the batholith to greenschist facies. Metamorphic isograds, subparalleling the faulted margin of the batholith, transect volcanic stratigraphy and coincide with major gold­ bearing shears.Gold mineralization is confined to north-striking, west-dipping shear zones where hanging­ wall amphibolite facies mineral assemblages retrogress to chlorite-carbonate-sericite-sulfide bearing schists hosting multiple generations of quartz-ankerite veins. The gold-producing portions of the Con and Campbell Shears occur where these structures transect an east trending thermal corridor. The corridor is defined by granitic plugs and a number of related breccia bodies, that can be traced outwards from the batholith across the greenstone belt.Prograde reactions of greenstone during amphibolitization effectively liberate fluids that partition metals. With retrograde reactions at shear zones, gold is precipitated with quartz due to the destabilization of sulfide and arsenic complexes. The coupling of regional prograde metamorphic and restricted retrograde metasomatic overprints suggest mineralization is temporally related to emplacement of the Western Plutonic Complex. Economic gold concentrations within the intrusive corridor indicates enhanced metamorphic overprint of hornfelsed greenstones enveloping satellite intru sives peripheral to the main batholith."

Jan 1, 1993

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By T. R. Eger

Miners can be exposed to whole-body vibration (WBV), when sitting or standing to operate mobile equipment. In order to prevent vibration-induced injury it is important to understand how miners can be exposed to vibration, the health risks associated with vibration exposure, methods to evaluate vibration exposure, and strategies to reduce vibration exposure. WBV exposure typically occurs when operating mobile equipment, such as a load-haul-dump vehicle, haulage truck, or dozer. The probability of health effects such as low back pain, neck pain, headaches, and gastrointestinal track problems occurring from daily vibration exposure can be determined based on criterion values published in ISO 2631-1 and EU Directive 2002/44/EC. A special case of WBV termed foot-transmitted vibration (FTV) occurs when a miner is exposed to vibration that travels through the feet. FTV typically occurs when standing on vibrating surfaces associated with the operation of locomotives, jumbo drills, bolters, or raise platforms; however, there is no set standard to evaluate health effects associated with FTV. Recent medical evidence confirms workers exposed to FTV can develop cold induced blanching of the toes, in addition to numbness and tingling in the feet and toes. In order to reduce the risk of adverse health effects from exposure to vibration, the hierarchy of controls (elimination; substitution; engineering; administration; and personal protective equipment) should be followed. Best practices should be used to minimize vibration exposure through equipment purchases (i.e. vehicles with lower vibration emissions and seats that attenuate vibration), reduced driving speeds, and improved road maintenance for example. The elimination of other risk factors, which increase injury risk when combined with WBV exposure, such as awkward working postures, should also be eliminated. Very little is known about FTV exposure therefore further research is required in order to develop exposure standards and identify prevention strategies.

Aug 1, 2013

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By J. C. Underwood

"The wear performance of grinding balls under conditions of impact and abrasion is affected by their chemical composition and structure. The selection of appropriate analyses and heat treatments that will provide both abrasion and impact resistance takes into account the effects of certain elements on structure and harden-ability, as well as the over-all effect of composition and hardness penetration on the residual stress pattern developed through heat treatment. Direct quenching from forging temperatures substantially increases hardenability over that obtained in reheat-quench practices, and can be done without undue risk of damage to the ball provided that the harden-ability bears the correct relationship to ball diameter.Average volumetric hardness and percent hardened volume are convenient parameters for quantitatively expressing the response to heat treatment and indicating anticipated wear properties. A number of factors which can lead to reduced wear life as a result of material or processing problems are reviewed and illustrated."

Jan 1, 1959

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By I. Filzwieser, A. Filzwieser

The Peirce Smith converter is the key metallurgical vessel in the majority of copper smelters. During the two step process, oxygen enriched air is injected through a row of tuyeres into the matte received from a primary smelting unit. Additionally, in the first step the iron content is oxidized into a fayalite slag by the addition of silica. During the second step, the remaining copper sulphide is converted into blister copper with a final sulphur content of approximately 200 ppm. The overall efficiency of this process is determined by the total reaction time, the slag quality and quantity, and the chemistry of the final blister copper. To increase the reaction kinetics during both stages, the METTOP Process Control and Regulation (MPCR) system was developed, which consists of four elements: OPC - Optical product control ACR - Automatic computer regulation GCU - Gas control unit GIS - Gas injection system The OPC system from SEMTECH records the optical spectrum emitted by the off gas flame providing immediate, detailed process information. Using this online data, additional gas can be automatically injected into the converter through a gas injection system opposite the tuyere zone. An improved oxygen distribution in the melt and the accurate determination of the process end point results in a significant reduction in the process cycle time. Furthermore, by maintaining the reaction closer to the equilibrium the final sulphur and oxygen content can be reduced compared to the conventional process. In particular, the final sulphur content can be lower than 70 ppm, eliminating the need for an oxidation step in the anode furnace.

Jan 1, 2007

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

The Industrial Minerals Milling Section of the Mineral Processing Division has been engaged for the past three years in a study of the separation of minerals, by means of electronic sorting equipment, on the basis of their colour. Considerable knowledge of the subject has been built up. Because the object of this study is application as a means of beneficiation, a number of examples of the separations achieved are presented. Introduction T 0 the mineral collector, the colour of a mineral may be pleasing, even fascinating; to the mineralogist, student or professional, it may also be practical. It serves, to some extent, as a distinguishing feature in many minerals, and helps to fix with reasonable accuracy the identity of a few. It may now become a useful tool of the mineral dresser. The idea of using a difference in colour as a means of separation of one mineral from another is not new. Hand sorting dates back to ancient time. However, the means by which this can be done mechanically was developed only during the past decade. As far as the Mineral Processing Division is concerned, interest dates from March, 1960, when the following item was observed in the

Jan 1, 1965

?Founded in 1969 by the Ruia family ?Diversified global business corporation with a balanced portfolio of assets in the manufacturing and service sectors; $15 Billion revenue in FY 2009-2010 ?Employs 70,000 people worldwide with offices in Asia, Africa, Europe and North America

May 1, 2011