Search Documents

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

"Developed by CRIRSCO, IRT is a document that draws on the best of the CRIRSCO-style reporting standards. These reporting standards are recognised and adopted world-wide for market-related reporting and financial investment.The IRT is not an international reporting code and does not supersede existing national reporting standards. Rather it is a guideline that encapsulates the content of these standards for the benefit of the international mining industry and its various stakeholders.The template is a 'living document' that is continuously updated and improved as new national laws, rules, codes and guidelines are created or amended.The International Template is advisory only and where national codes already exist, these will take precedence. The International Template is intended to assist those countries that either do not have a reporting code or whose code is outdated, to produce a new code consistent with international best practice. It also provides a consolidated version of national codes that reflects their compatible international components and may thus be used in comparisons with other international reporting systems. The word 'Template' is used advisedly to indicate that this document is a model for code development and does not in itself constitute a 'code' which implies that it has legal or other regulatory force.From this point forward, the Template includes words that imply a mandatory action, such as ""requires"", ""applies"", ""must"" etc. This is to enable the Template to be easily adopted by countries and organisations wishing to do so, and does not imply that the Template itself is a mandatory reporting standard.INTRODUCTION2 In this edition of the International Reporting Template (""The Template""), important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Template clauses using indented italics. They are intended to provide assistance and guidance to readers for interpreting the application of the clauses in the Template.Indented italics are also used for Appendix 1 — 'Generic Terms and Equivalents"", and Table 1 —'Check List of Assessment and Reporting Criteria' to make it clear that they are also part of the guidelines for the application of the Template.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that may be considered in addition to the Codes of Ethics or Practice normally applying to members of professional institutions."

Jan 1, 2003

By A. S. Knight

THE breaking and handling of ore is obviously the most important consideration when the layout of a new mine is contemplated. The problem must be attacked with due regard to the claim area of the property, the dip of the orebody, the anticipated percentage of payability, the width of the reef, and the amount of dislocation anticipated by dykes, faults, or sills. Among these, as far as East Geduld is concerned, the three most important items are: Area. 2,640.5 claims. Average dip 12° (from flat to 35°) Average channel width 36 inches. We are fortunate on the Witwatersrand in &apos;chat there is usually sufficient information available from surrounding properties to determine, within narrow limits, the factors mentioned above. With this information avail-able, the choice of layout is not limited, and it will be found that on the Witwatersrand each group has developed its own technique to suit its individual requirements. On East Geduld, the layout of the property for handling ore is known as the endless-rope haulage system. Following is a brief description of the general principles followed.

Jan 1, 1942

By J. M. Cummings

CONSIPERABLE information on the industrial or non-metallic mineral resources of British Columbia has been published. For a general resume of the subject, reference may be made to a paper presented by A. M. Richmond before the Annual General Meeting of the Institute in 1935 (1). To avoid duplication, the present paper is confined to a discussion of the existing industrial mineral industry of the Province and of the factors governing its present and future development. British Columbia&apos;s mineral production in 1936 had a value approximately 15 per cent of that for the whole of Canada. Preliminary estimates for 1937 indicate that this proportion has been maintained, although the totals have increased about 25 per cent. The following table presents comparative figures, for the year 1936, illustrating the relative importance of the major divisions of the mineral industry in British Columbia and in Canada as a whole.

Jan 1, 1938

By W. J. Wolfe

"Quartz Hill is a large, low- to moderate-grade quartz vein stockwork porphyry molybdenum deposit, discovered in 1974 during a regional stream sediment geochemical reconnaissance survey of southeast Alaska conducted by United States Borax and Chemical Corporation. Mineralization is localized in the upper parts of an Upper Oligocene (30 Ma) composite quartz monzonite stock which is emplaced discordantly into older Cretaceous to Early Tertiary terrain of the Coast Range igneous metamorphic complex of the northwest North American Cordillera. Subsequent fault-controlled, complex multi-stage intrusion, concentrated in the core of the Quartz Hill stock, produced successive pulses of hydrothermal alteration and molybdenum mineralization at about 27 Ma. Overall, the deposit is tabular and flat-lying and well suited to open pit mining. The 0.05% MoS2 grade limit covers an area of approximately 1500 m by 2750 m and extends to a maximum depth of 520 m below surface. Details of grade distribution show two separate lobes of higher grade material within the larger low-grade deposit.A ten year program of exploration drilling, underground development, sampling and metallurgical testwork led to a 1983 feasibility study based on a resource of 1600 million tonnes grading 0.127% MoS2 at a 0.08% MoS2 cutoff The large size of the deposit and its homogeneous grade distribution, typically showing gradual outward decrease of grade, makes in pit grade selection practical at several cutoff levels. Cominco Ltd. now reports a Probable Resource of 210 million tonnes averaging 0.22% MoS2 with a further Possible Resource of 1100 million tonnes averaging 0.12% MoS:z. At low molybdenum metal prices which have persisted for 10 years since the molybdenum price spike of the late 1970s and early 1980s, the Quartz Hill deposit is sub-economic."

Jan 1, 1995

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By ANNE FUZESY

Soluble potassium salts in bedded underground salt deposits supply most of The world demand for potassium f or agricultural and industrial use. The potassium salts, sylvite and carnallite, were f irs, noted in drillcores in southern Saskatchewan during The search for oil and gas in ihe early /940s. Problems in shafi sinking beset pioneering potash companies, however, and cominuous production did no, begin uniil 1962. Powsh deposits in southern Saskatchewan occur within ihe uppermost 60 111 of the Middle Devonian Prairie Evaporite a, depths in excess of 900 m. Four groups of po/ash-bearing haliie beds have been distinguished: the Esierha-::,y, White Bear, Belle Plaine and Paiience Lake members. Powsh deposiis extend a jell' kilomeires into Manitoba and south imo orth Dakoia and non heasiern Moniana. Individual potash-rich beds are extensive and consistent in grade and Th ickness. Local th ickening occurs where carnallite is the dominani poiash mineral. Th e preferred ore, sy lviniie, is a clean mixiure of sylvite and haliie. Carnalliie and insolubles are avoided wherever possible because of Their detrimenwl effects on mine stability, grade and refining. Sy lvin ite is exTracted by underground mining or brought TO swjace as brine in solution mining. Poiash is separaiedfrom halite byfloiation or sequential crystallization. The refined produci, potassium chloride, is employed as a fertilizer ingredient as well as in chemical and other industrial capaciiies. The ten poiash mines of Wesiern Canada all are in Saskatchewan and account for aboui 25 per cem of world production. Faciliiies are being expanded, and a new mine and refinery was planned for ihe Breden bury area. Deposiis in Manitoba also were being evaluaied.

Jan 1, 1984

By Richard J. Wardle, Ambrose F. Howse

The industrial minerals industry in Newfoundland and Labrador is a significant contributor to the provincial economy. The variety ofcommodities produced reflects the diverse geological environment from which they come. A highlight of the past decade has been the continuing development of dimension stone quarries, with producers now active in anorthosite, gabbro, granite and sandstone. Other dimension stone prospects have been identified and are in various stages of assessment and development. Western Newfoundland hosts a large resource of limestone, dolomite and marble. It provides raw material for industries that produce Portland cement, agricultural limestone and aggregate, as well as chemical-grade limestone and dolomite products. In western Labrador, dolomitic marble is quarried for use in the production of self-fluxing iron ore pellets. The recent opening of a new gypsum quarry at Fischells Brook signalled the beginning of a new era in the commercial production ofgypsum, a commodity which the province has produced since the 1950s. Hopefully it will emulate the nearby Flat Bay Quarry (now closed) which was a long-time exporter to markets along the U.S. eastern seaboard, in addition to supplying local demands. Oil production and continuing exploration in the Newfoundland offshore has renewed interest in local barite deposits for potential use in drilling fluids. Already there has been some production from the Collier Point deposit, and at Buchans, an existing plant is being refurbished to recover barite from a large tailings pond. Emerging new industries include the development of an antimony mine in central Newfoundland, the development of silica deposits near Labrador City for silicon metal production, and reactivation of the St. Lawrence fluorspar mine. The province has many deposits with development potential such as rare metals at Strange Lake, white marble at Roddickton and salt deposits near St. George's Bay region.

Jan 1, 2001

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012