Search Documents

By J. A. Morgan, W. A. Barclay, J. C. Pedersen, I. C. Campbell, D. S. Bubar, R. P. Taylor

"Abstract - The Lilypad Lakes property is host to a group of Ta-mineralized dikes that occur over an area of at least 10 km2. Field relationships are consistent with a syn- to late syn-tectonic timing for their emplacement (with respect to the major regional D1 episode of deformation), with several of the dikes exhibiting a steeply dipping, open, S- to M- to Z-shaped fold geometry. Individual dikes range up to 30 m wide (Rubellite Dyke, Pollucite Dyke), have strike lengths of up to 750 m (e.g., JJ Dyke), and are continuous to depths of greater than 250 m (e.g., Rubellite Dyke, Pollucite Dyke). Typically, they display sharp intrusive contacts characterized by the development of thin, holmquistite-rich haloes. The Tamineralized dikes are comprised of silica- and alumina-rich, sodic, granitic pegmatites that display extreme levels of geochemical fractionation (K/Rb typically < 10.0, as low as 2.2; Nb/Ta typically < 0.20, as low as 0.03), and enrichments in an economically important group of lithophile elements, most notably Li, Rb, Cs, and Ta. Geochemical assays of individual surface grab and drill core samples have yielded values as high as 1.51 wt.% Li2O, 1.25 wt.% Rb2O, 6.21 wt.% Cs2O, and 0.108 wt.% Ta2O5. Diamond drilling has established the presence of wide (~20 m), potentially ore-grade intersections of Ta mineralization (>0.045 wt.% Ta2O5) in both the Rubellite and the Pollucite Dykes.Three Ta-oxide minerals (microlite, wodginite, manganotantalite) of primary origin predominate in the Ta-mineralized dikes, where they occur as fine, disseminated grains in the albite-rich pegmatite matrix. The sequence of crystallization is typically manganotantalite wodginite microlite, which conforms to a well-established paragenetic sequence for rare-element granitic pegmatites in general. All three of the primary Ta oxides are characterized by a high degree of chemical purity (e.g., average Ta concentrations in microlite from 77-79 wt.% Ta2O5), a compositional feature consistent with the extreme levels of geochemical fractionation characteristic of the host granitic pegmatites, and one that indicates that the Lilypad Lakes pegmatites are likely to produce Ta mineral concentrates of the very highest quality.Locally, a second generation of Ta minerals is present, restricted to small vugs in the pegmatite matrix that are surrounded by fine aggregates of K-rich mica or clay. The secondary Ta minerals are dominated by microlite, which is typically intergrown with fluorite and Fe-sulphides, and is distinguished from its primary counterpart by its lower Ta content (around 70 wt.% Ta2O5) and much higher concentration of uranium (up to 9 wt.% UO2). Also, secondary microlite consistently yields low analytical totals from electron microprobe analysis, suggesting that it is H2O-rich. The presence of this second, vug-related generation of microlite, together with the occurrence of localized networks of crosscutting fractures that host high concentrations of Cs and Rb (in the minerals pollucite and Rb-Kfeldspar), suggests that a late-stage, fluid-dominated metasomatic/hydrothermal event may have been important in certain sections of the dikes, and has effected a redistribution of the economically important elements Ta and Cs."

Jan 1, 2005

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 &apos;by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola&apos;s current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter&apos;s Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all &apos;hot-metal&apos; basis.

Jan 1, 1938

By Charles G. Kemsley

MR. C. R. WHITTEMORE: It is interesting to note that the mining industry is making increased use of alloy steels for drilling. They will undoubtedly lead to greater footage at lesser cost. Mr. Kemsley states that, for use in hard ground, the shanks are brought to a hardness of 435 to 440 Brinell by heating them to approximately l,800°F. It seems to me that this temperature is excessively high-it is considerably above the critical point of the steel. The only effect of such a high temperature is to lessen considerably the impact resistance of the steel. The possibilities of an oil quench, followed by a tempering draw which does not lessen the hardness of the steel too much but increases its toughness, might well repay further study; also the temperature control, a factor which depends on the composition of the steel. However, service results are undoubtedly the best criterion of practice. MR. KEMSLEY: I would like to point out that the steel is not quenched at 1,800°F. After heating to this temperature, it is laid aside to cool gradually; this high temperature is necessary to produce the required hardness by simple normalizing-cooling in still air. We all know that ideal conditions for hardening steel demand salt baths and furnaces with automatic temperature control, but for most companies the cost of such equipment having sufficient output capacity is prohibitive. The end we are trying to attain is to make good drills at a cost that will be within the means of any mine.

Jan 1, 1942

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By R. P. Nicholson

On September 3rd, 1947, the Acadia Coal Company put into operation a central coal preparation plant. This plant was designed to process all coals mined by this Company in the Pictou County coal field. The problem, briefly, was to make a three-way separation of the raw coal fed into the plant. It was desired to remove all stone, metal, and wood from the marketable coal and to produce a splint coal from the raw material which would be suitable for making power. This splint coal product is belted directly to the power plant which is adjacent to the wash plant. To attain this object it was therefore necessary, first, to wash the raw coal, removing all splint, stone, metal, and wood. The stone, metal, wood, and highest-ash splint had then to be removed by a second washing in order to obtain the lower-ash splint for use in the power plant. The plant is on the east side of the Allan colliery, in the town of Stellarton (see accompanying photograph). It is of steel frame construction with wood siding, covered on the exterior with corrugated galvanized iron. Considerable concrete had to be poured for the foundation piers as the plant site is largely &apos;fill&apos; ground. This necessitated the construction of extremely heavy footings containing a large amount of reinforcing steel. In all, 884 cu. yds. of concrete were poured for the various pits, tanks, and foundations; its average test was about 3,500 lb. per square inch. At the time the plant was constructed, the steel shortage in Canada and the United States was acute and, in order to obtain steel for the structure which is four stories high- an unused part of the Allan bankhead was torn down. Enough steel was obtained from this demolition to fabricate the new plant.

Jan 1, 1948

By R. K. Netolitzky

The Weedy Lake, Tower Lake, and Wedge Lake gold deposits illustrate contrasting styles and different ages of mineralization within the same district. The discovery of these deposits was the result of systematic exploration of gold occurrences noted during research of assessment files. The Weedy Lake and Tower Lake depo its reflect a late-stage gold mineralizing event. The e deposits developed along the same major structural break, and also display simi lar mineralogy and alteration patterns. Mineralization is developed in all the lithologies present. The Wedge Lake property, while having occurrences similar to the Weedy and Tower deposits. has the more important Twin Zone which best fits a volcanogenic exhalative model. The Twin Zone has a complex structural history without a recognizable alteration halo. The setting may be proximal to a hydrothermal vent. Mineralization is hosted within a mixed ulphide/oxide/silicate facies iron formation breccia. and the gold is intimately associated with arsenopyrite. The origin and age of the brecciation is key to understanding the mineralizing event. Traditional prospecting procedures in conjunction with conventional B-horizon soil geochemistry were instrumental in the Twin Zone and Weedy lake disco,•eries. Tower Lake was a prospecting discovery partially defined by previous drill programs. This deposit was also identified by B-horizon oil sampling.

Jan 1, 1986