Search Documents

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013

By Liangtian Liu, Tie Ou, Guangqiang Li, Chenghuan Yu

For stabilizing the production of containing nitrogen steels, a study on nitrogen absorption behavior of killed molten steel has been carried out by means of the RH vacuum device in which nitrogen was used as a driving gas. The results showed that there was an increase of nitrogen content in molten steel under vacuum processing but the rate of nitrogen absorption was slowed down by the surface active elements. Therefore, a kinetic equation for nitrogen absorption of molten steel with apparent first order reaction was derived by constructing a modified model in which the adsorption of closed surface site was taken into account. The experimental results confiimed that the calculated values agreed with the observed ones. This model is suitable for the prediction of nitrogen adsorption operation for containing nitrogen steels.

Jan 1, 2004

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental 'evidence' found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By R. P. Townsend

It is a widely accepted "fact" that a Koepe friction hoist is generally the best solution for production hoisting when compared to a double drum hoists. This would appear to be true if one looks at the initial capital cost of just the hoist, and also if one compares the size of the motors selected for the duty. But is this the whole story? What are the longer term costs involved in the hoist's operation, and what are the relative efficiency's of the two designs? Perhaps the Koepe hoist design enjoys a better reputation than it deserves.

Jan 1, 2011

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By Carl Edmunds

Talk Outline Deposit?s Vital Statistics and Economic Environment Regional Geologic Setting Deposit Geology UBC Research Search Model and Current Exploration Plans Kemess Operations Kemess South Mine Mining rate (2006) ?135,000 tonnes / day Mill throughput (2006) ?52,000 tonnes / day Average Annual Production ?300,000 oz gold and 75 million lbs copper ?Production until mid-2009 Kemess North > Open pit reserve 423.8 million tonnes @ 0.3 g/tgold and 0.18% copper > 4.1 million ounce gold reserve (127 tonnes) > 1.45 billion pound copper reserve (636,000 tonnes) > 0.75:1 Strip Ratio

May 1, 2006

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By G. Reuben Yourt

IN 1935, Wright-Hargreaves Mines, Limited, initiated an enlarged programme of ventilation. In the mine, surveys were made from time to time by the geological staff, and improvements in ventilation were effected to accord with progress in mining as greater depth was attained. In the summer of 1938 an engineer was trained in the technique of dust sampling. Instruments and equipment for this purpose, such as konimeter, microscope, furnace, etc., were purchased, and a suitable office, equipped with laboratory facilities, was provided. The full time of the engineer is devoted to ventilation and dust control. On surface, in the mill crushing-plant and in the assay office and sample crushing room, an elaborate arrangement of hoods and exhaust systems has been installed to eliminate the dust. These installations, however, are not described in the present paper, which deals only with an extensive programme of underground ventilation as a method of coping with high dust concentrations, increasing temperatures and high humilities.

Jan 1, 1940

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By C. Rocha R.

Petioles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world's foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Petioles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process, particularly the operation of the jarosite circuit and its effective removal of impurities such as arsenic, antimony, indium, selenium and tellurium, is reviewed.

Jan 1, 2006

By M. Cossette, P. C. A?tcin

At present there is considerable confusion in the asbestos industry with regard to density and porosity measurements of asbestos. In order to clarify the situation, various notions of porosity and density are defined by means of simple schemes and clear symbols are proposed to denote them. An experimental procedure is then preposed and outlined, which is based upon Archimedes' principle. Experimental conditions at each stage of the method are explained clearly in order to minimize the opportunity for errors. Finally, the results of a study on the porosity and density of asbestos minerals having various characteristics are presented.

Jan 1, 1972

By B. Jin

Removal of fluoride and chloride by alkaline washing from direct lead smelting dust which originated from an Ausmelt furnace is reported. The results show that the fluoride removal efficiency increases with an increase of alkaline concentration, alkaline washing temperature and time. The L/S ratio has little effect on fluoride and chloride removal efficiency. A new flow sheet for removal of fluoride and chloride from the dust was successfully proposed according to the results. Fluoride and chloride removal efficiencies are more than 53.68% and 63.18% respectively using the flow sheet under the optimum parameters of temperature 338 K, L/S ratio 3:1 and alkaline washing time of 1.5 h. The contents of fluoride and chloride in the alkaline washing residues can meet the standard of zinc purity as hydrometallurgical materials for zinc processing.

Jan 1, 2014

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019

By A. M. Richmond

Introduction The apparent commonplace, and prosaic, nature of building-stones, lime, cement, gypsum, and clay products, and many other miscellaneous non-metallic minerals, such as abrasives, barite, diatomite, magnesite, mica, slate, salts, etc., and their everyday appearance and necessary in our lives, has removed much of the glamour, romance, and speculative attractiveness so frequently associated with our gold, silver, lead, zinc, and copper mining ventures. However, it will be readily appreciated, with but a brief study of the thirty-five or more non-metallic minerals and products which are mined, prepared, or are known to occur, in British Columbia, that the 'industrial minerals' industry in the Province has an abundance of interesting technical problems, is fraught with speculative possibilities, and, as such, fully deserves much more technical attention than it has hitherro received. The brief notes presented in this paper show, in summary form, the magnitude of the British Columbia industrial and non-metallic mineral industry; outline in synoptically form the principal deposits of non-metallic minerals presently known; and indicate in a general way a few of the possibilities which exist in the Province for the expansion of the industry. For convenience in presentation, the assembled material has been divided into four sections: 1.-Sraristical information 2.-Strucrural non-metallic minerals 3.-Miscellaneous non-metallic minerals 4.-Non-Metallic mineral possibilities in British Columbia 1. -Statistical Information The writer does not propose to dwell at length on the statistical comparisons and deductions which may be drawn from the four tables which have been compiled for this section of the paper, nor is it considered essential, as the figures present a most emphatic story in themselves.

Jan 1, 1935

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By W. J. Farley

Location and History The Sherritt Gordon mine is in northern Manitoba, one hundred miles north of The Pas and forty miles northeast of Flin Flon. The original discovery was made by a Cree indian, Philip Sherlett, in 1922. The claims lapsed in 1924 to be re-staked and optioned by various mining groups who carried out a certain amount of development work before relinquishing their options. In 1927 the present Company, Sherritt Gordon Mines, Limited, was formed to take over the property. Production commenced in 1931, but in the following year operations were suspended and it was not until 1937 that the prevailing price of copper pemitted resumption as an economic operation. The mine has operated continuously from that time to the present. Total production to the end of 1947 has been: Copper . . . . . . . . . 301,813 . .,345 pounds Zinc . . . . . . . . . . . 112,636 tons of concentrat (50% zinc) Gold . . . . . . . . . . 83,070 ounces Silver . . . . . . . . . 2,651,317 ounces General Geology The consolidated rocks in the vicinity of the mine, all of Precambrian age, are a series of gneisses and form a part of a great area of what are known as the Kisseynew gneisses. The Sherritt is the only known economic base-metal deposit to occur within the Kisseynew series. Extreme metamorphism has produced recrystallization that has imparted a decided igneous-like texture to many of the units. However, the gneisses are predominantly of sedimentary original although the most basic member, a hornblendegarnet gneiss, is considered to be an altered basic flow. Figure 1 illustrates the intricately folded structure and the succession of roe types. The footwall enclosing members are of sedimentary origin and represent quartzite and arkosic and greywacke derivatives. The contact footwall member is gneissic quartzite, a medium to coarse grained rock composed mainly of quartz with minor altered feldspar (orthoclase and plagioclase), muscovite, chloritized biotite, and magnetite. Most phases of this unit show varying degrees of granitization.

Jan 1, 1949