Search Documents

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By J. Shanks

A S far back as 1925, Brazeau Collieries, Limited, became interested in .briquetting. This was brought about by complaints from their principal customer that stack losses, due to a high percentage of fine coal in their mine run, were excessive. The Company considered oil spraying of the fines. This, after some experiments and tests had been made, was ruled out as uneconomical and impracticable. When sufficient oil to be effective was put into the fines, it caused the coal in the tender of stoker-fired engines t0 arch over the screw feeder. The Company ultimately placed their problem in the hands of the Re-search Department of the University of Alberta. Experimental work was carried on by this department over a period of more than a year. The results obtained and the experience gained in this research work were conveyed to Brazeau Collieries in a report dated October 31st, 1929, and in a supplementary report dated February 2nd, 1935. Most of the results obtained in experimenting with Brazeau coal are embodied in a brochure, reprinted from the proceedings of the Second International Conference on Bituminous Coal, Vol. 19-24-28, entitled Principles in the Briquetting of Coking and Non-Coking Bituminous Coals, by E. Stansfield and W. A. Lang. All who are interested in briquetting should read this brochure. In the writer's opinion, iris the most important treatise on the subject printed in recent years. The results given in the paper are, of course, those obtained in laboratory investigation. It was pointed out to the writer that it would be most interesting to have such results correlated with those obtained in commercial practice. In this short paper, an attempt is made to do so.

Jan 1, 1942

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

By Janice Zinck

?Past? Images of Mining ?Historic practices have been poor ?Mining still widely perceived as environmental ?spoiler? ?Public only hears the bad news stories. Lessons Learned from the Past ?Sustainability matters ?Recognition of social and environmental responsibilities ?Recognition of importance of public concerns and perceptions ?Community engagement

May 1, 2009

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006

By D. G. Osborne

"The paper describes current 'tools' available to the coal preparation engineer for carrying out the evaluation of data, process design, selection of equipment and layout and design of coal preparation plants.Laboratory and pilot-scale equipment is widely available and test data can be used to provide valuable design information regarding capacities and sizing for specific applications. Pilot plants, unless they fit closely to the basic design envisaged for the eventual commercial plant, C(In often provide only limited useful information.Computing aids such as equipment simulation, plant modelling, etc. are becoming widely applied for establishing design criteria and investigating flowsheet options . Other computer tools such as computer-aided design systems are taking over some of the time-consuming tasks of detailed layout and design and estimation of quantities, etc. and providing the means for detailed examination of more than a single option.Besides computer modelling there is also physical modelling of plant buildings, plant sites and entire proposed mining areas; the former can be especially useful in finalizing design and threading' pipework and electrical reticulation systems through the plant without the resultant risk of impairment of flow, obstruction or wastefulness. Not the least of the benefits of plant models is the assistance provided for training new operating and maintenance staff."

Jan 1, 1985

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By David E. Pearson

"There are many tests that can be used to characterize and classify coals, and describe their quality. One of the easier tests, and most versatile in its application, is petrography. Rank and coal type are precisely defined by petrographic evaluation, and in this paper they are compared with other definitions of rank and coal type. Brief descriptions are given of the various rank tests, and of rheological and coking tests used to describe coking-coal quality in Canada. Similarly, tests used to evaluate thermal coal quality are discussed. Finally, the use of these tests as parameters to classify Canadian coals is examined with reference to four coal classifications.Introduction Among all coals there are two independent variables that are required to evaluate coal quality. These are, coal rank and coal type (or composition), and although coal petrography can be used to precisely define them, other methods are often used to provide values that are, in fact, functions of rank and coal type. For example, volatile matter yield is used as a proxy for rank, and free swelling index is used as a proxy for coal type in the International Classification of Hard Coals by type. Currently, there are a number of methods in use in Canada to define rank. The approach taken here, (obviously the author's bias), is that Romax, the mean maximum reflectance of vitrinite, is both a quick and an accurate measure of rank. It is logical to compare the other techniques employed in the measurement of rank to this favoured method. Coal type is, in theory at least, simply a quantitative measure of the various varieties of coal. In practice, the microscopic entities are assigned to a Reactive or Inert category, and at that point objectivity fades from petrography. Despite this somewhat subjective approach, petrographic composition of coals remains an independent variable of such.importance that its place in the evaluation of coal is essential. In this paper, a variety of me.thods that are used to assess rank and coal type are reviewed and compared; the influence of these variables over other parameters that are used to determine the quality of metallurgical and thermal coals is examined, and their usefulness in coal classifications is discussed."

Jan 1, 1985

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967

By P. K. Kaiser, S. M. Maloney, S. P. Singh

"Corrosion of underground support measures constitutes a concern to industry in both safety and economic terms. It also represents a potential market for corrosion resistant materials such as stainless steel.In order to assess the market potential for a stainless steel friction rock bolt, a review of current corrosion processes and remedial or preventative measures in the underground environment was undertaken. This was supplemented by distribution to industry of a detailed questionnaire, concerning the magnitude and extent of support corrosion and the costs of current support measures, and by visits to selected sites. Following data synthesis, support costs were established and the economic benefit of stainless steel rock bolts evaluated.Stainless steel rock bolts can be an effective cost reducing measure in unscreened areas requiring frequent reconditioning. Their benefit is rapidly diminished, however, if only partial reconditioning is required, the reconditioning interval is long or if screening is required.While most industry personnel are receptive to the application of stainless steel support measures, the localization of corrosion problems and the potential high cost of this type of support are barriers to its widespread implementation. They have potential for use in extreme environments. However, this relatively small market may not be economically viable.IntroductionFriction rock bolts are the simplest of all interior rock fixtures. The friction resistance to sliding of the rock on the bolt is generated by a radial pressure against the borehole wall over the length of the bolt. Two types of friction rock bolts are currently marketed, the Split Set and the Swellex.Unlike conventional point anchor bolts, friction rock stabilizers may move relative to the rock strata and maintain their capacity even if rock shifts, a condition that sometimes loosens or breaks conventional bolts. Ease of installation, effectiveness in jointed as well as weaker rock, and the possibility of having relatively long bolts are a few of the many advantages which generate considerable interest in the application of friction rock bolts (Wijk and Skogberg, 1982). However, due to their thin-walled construction and large surface area, frictional rock stabilizers are more susceptible than conventional bolts to damage by corrosion. For this reason, they are normally not recommended for long-term use (Jolly and Neumeier, 1987).In light of the above discussion; the Nickel Development Institute commissioned a study by the Geomechanics Research Centre with the objective of generating a credible database for the assessment of the feasibility of a stainless steel friction bolt system in corrosive ground and mine environments."

Jan 1, 1990

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By H. Soto, P. Lacombe, R. del Villar

"During the summer of1989, Les Mines Selbaie, with the cooperation of Université Laval initiated a research project to evaluate the column flotation technology for its concentrator near Joutel, Quebec. The experimental work involved both a 5 cm by 11 m laboratory column and a 45 cm by 10 m home-made pilot unit Amenability tests were conducted using both units on various streams of the plant. Results showed that columns are not suitable for the copper cleaning circuit because the loss of precious metals, associated with the rejected pyrite, overcome the improved copper metallurgy. On the other hand, column testing at the zinc circuit showed improved zinc selectivity.Scale-up testing was', therefore, conducted on the first zinc cleaner concentrate using the laboratory-size column. The influence of variables such as porous parger grain size, wash water flow rate, airflow rate and froth depth values on column performance was' first assessed. Scale-up parameters were then determined using the optimal operating conditions from the previous tests. Simulation facilitated the determination of the most convenient plant-scale column arrangement.A number of conclusions concerning the experimental determination of scale-up parameters are also presented."

Jan 1, 1993

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996