Search Documents

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By F. D. Ball, D. E. Gemmell

"Coal mining in New Brunswick dates from the year 1639, when, as today, coal was produced from the area surrounding Grand Lake near the geographic centre of the province. Current production by N.B. Coal Ltd. is approximately 453,000 tonnes per year and comes from a single, thin Pennsylvanian age seam. The history of development and understanding of the geological setting of New Brunswick coals is discussed, beginning with the work of A. Gesner in 1839. The lithostratigraphic sub-divisions of the Pennsylvanian strata proposed by various workers are summarized and the present hypothesis that only biostratigraphic subdivision is possible is detailed. The Pictou Group, which includes the New Brunswick coals, consists of repetitive sequences of sediments consistent with flu vial and upper delta plain sedimentation. The development of coal mining in the province has progressed from horse-powered stream-bank stripping operations prior to the late 1800s through to the present use of open stripmining techniques utilizing eight walking draglines of various sizes. During the intervening years the introduction and eventual phasing out of underground mining occurred with the near termination of the coal mining industry in the province prior to 1973. The coal seam worked by N.B. Coal Ltd. averages 46 cm in thickness, has never been found to be more than 76 cm thick and has both high ash (12.4 -31.1%) and sulphur (4.9-7.8%) content. The wide variety of coal beneficiation studies and tests completed on New Brunswick coals have lead to the conclusion that a washed New Brunswick coal product could be expected with 10 to 12% ash, 5 to 6% sulphur, and 30,225 to 31,388 1/gm. Recoverable coal reserves, including those in the area licenced to N.B. Coal Ltd. and those licenced, although not yet in production, to both the St. Lawrence Cement Co. Ltd. and Provincial Holdings Ltd. at Lake Stream and Beersvil/e, total 60 million tonnes. At present, coal in New Brunswick is removed from prospecting and staking and all existing and future coal exploration and development will be administered by agreement under the Mining Act. Based on the results of a recently completed drilling project undertaken by the Department of Natural Resources, seventeen coal exploration blocks which carry minimum work commitments will be offered to the New Brunswick Electric Power Commission on a sixty-day first right ofrefusal basis. Those blocks not taken up by the Power Commission will be offered under the same commitments to the private sector."

Jan 1, 1985

By L. Magne, A. Pinto, M. Maldonado, J. A. Finch

Estimation of gas holdup from electrical conductivity measurements has been used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the electrical conductivity of the dispersed phase, continuous medium and the resulting mixture (dispersion). When applied to inferring the collection zone gas holdup in a three phase system and to facilitate real-time on-line measurement, the slurry is assumed to behave as the continuous medium and gas bubbles as a nonconducting dispersed phase. This article derives an equation for estimating gas holdup in a three phase system, eliminating the assumption that the slurry behaves as a continuous medium but rather as a dispersion of non-conducting solid particles in water. In this formulation only water behaves as the continuous medium in the sense of Maxwell, and gas holdup in a three phase system is then calculated from the application of the Maxwell model twice: (1) to determine solid content in a two-phase system, and (2) to determine solid plus gas holdup in a three phase system. To validate the new equation and quantify the errors incurred by assuming slurry is the continuous phase a laboratory flotation cell was instrumented to continuously measure the conductivity of two and three phase dispersions with known solids contents. As the amount of gas in a lab flotation machine is difficult to measure directly or by another indirect technique such as using pressure signals, 2.5 mm dielectric plastic spheres having a density of ca. 1.3 g/cm3 were used instead of air bubbles for validation. Experimental results demonstrated that the continuous medium assumption underestimates gas holdup and that the resulting bias error increases linearly with the solid content and decreases with the magnitude of gas holdup.

Jan 1, 2016

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By G. Van Weert, O. Wang

"As part of a general review of processing double refractory ores through Barrick Gold’s autoclaves / CIL facility at Goldstrike, blanking the preg robbing native carbon in the process solids with hard (m.p. 55 - 60 º C) paraffin wax was studied, specifically in relation to pressure oxidation. The improvement in CIL gold extraction was found to depend on the wax addition point, with hot, dry contacting of the ore in the presence of wax - prior to POX - yielding the largest, most consistent improvement in gold extraction.INTRODUCTIONDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including Carlin Trend, NV, deposits, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (Thomas, 1994). It is the latter route to which this paper refers.The second barrier refers to the actual gold recovery. Gold may be extracted from the pressure oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This is taken advantage of on a large scale by gold millers, who use manmade activated, i.e., graphitized carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold cyanide bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold. The second barrier becomes problematic when the ore naturally contains graphitic orcarbonaceous material, hereafter referred to as native carbon (versus the man-made activated carbon). This material may also adsorb gold cyanide in competition with the activated carbon. Since the native carbon is ground with the ore it is much smaller than the activated carbon. Any competition between the two carbons may produce a loss of gold from the pregnant leach liquor to the process tailings. This phenomenon is called “preg robbing”. Goldstrike ores come from the Carlin trend, which is known for the occurrence of native carbon (Adams & Burger, 1998; Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001; Tretbar, 2004)."

Jan 1, 2012

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By D. Virely, M. Gasc-Barbier, J. Guittard

"The valleys of the Dordogne and the Vézère (France) have been inhabited since prehistoric times, as evidenced by the famous site of Lascaux. A few miles away, the village of La Roque-Gageac is also a very popular tourist destination (about 1.5 million tourists per year): The village is sandwiched between a massive limestone cliff and the Dordogne river. The collapse of a cave roof high above the village in January 2010 led us to characterize instability together for the cave and the whole cliff and propose a adapted instrumentation to monitor the fracture openings in the rock mass that are linked to climatic variations. Measurements have been going on and been recorded for nearly 4 years. They point out the role of thermal stress fatigue in the breakdown of the rock mass. In this paper we describe the site under study, the instrumentation and its main results. INTRODUCTIONThe phenomenon of thermal fatigue has been very little studied as far as rocks are concerned, whereas it is rather well characterized for other types of materials: Elsevier published a journal dedicated to fatigue (International Journal of fatigue). In the case of rocks, thermal phenomena and their impacts on mechanical behavior have been analyzed from a micro-structural point of view, and it is now well-known that an increase in temperature causes a dilatation of crystals (Arnould et al., 2004; Berest & Weber, 1998). This dilatation may lead to the development of inter-granular traction and compression stresses, and if those stresses are greater than fracture strength, inter-granular and intra-granular cracks may take place. On the other hand, the fatigue phenomenon (cyclic repetition of a temperature variation which is less extreme than the one that may lead to this inter-granular or intra-granular fracture) is a phenomenon which has not been much studied.The principal studies on thermal fatigue on rocks come mainly from the field of geomorphology, particularly in connection with the analysis of the evolutions of past climate that can explain the present shapes of those landforms: those studies remained essentially qualitative and not quantitative. Le Ber & Oter Duthoit (1987) proposed a thermal and thermodynamic approach to analyse the disaggregation of rock masses. This analysis is dedicated to the study of paleoclimates and was implemented to better understand the formation of slope deposits in order to propose transfer models permitting the reconstruction of the climactic conditions contemporary to their appearance. Since deterioration in the cliff only appears after several cycles, it means that it is a gradual and irreversible deterioration which leads to an increase of the « disorder ». Seen from a macroscopic system point of view, this irreversible evolution is quantified by the internal creation of entropy."

Jan 1, 2015

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By D. Janney

Kennecott's Utah Smelter commenced operations in June 1995 utilizing Outokumpu Flash Smelting (FSF) and Kennecott-Outokumpu Flash Converting (FCF) technology. After some initial teething and equipment problems the smelter achieved its design capacity in mid-1997 and now processes over 1.0 million tonnes of copper concentrate per year with exceptional environmental performance. The smelting furnace has operated for 11 years and the converting furnace for 5 years without major shutdowns. The first major smelter shutdown commenced in September 2006 after extensive planning. The FSF was completely re-bricked and the latest above and below bath containment systems installed. The FCF was inspected and re-bricked with some improvements made to the above bath containment system. The FCF life is now anticipated to be the same as the FSF. Numerous improvements and modifications were made to the rest of smelter facility including extensive upgrades to the dry electrostatic precipitators. Production ramp-up was smooth with the smelter now frequently operating at acid plant capacity.

Jan 1, 2007