Search Documents

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By H. G. Warrington

Abstract As part of the active development programme pursued by Dominion Magnesium Limited since 1945, a modern extrusion plant was erected and has been in operation for about twelve months. The only source of nigh purity magnesium in the world, Canadian metal is produced by metallurgical processes within the frame-work of the mining industry, which gives a different viewpoint to every phase of production from other world suppliers of commercial grade metal whose operations are based on chemical industries and techniques. The superior properties of corrosion resistance and grain refinement have aided a programme of standardization, reducing the number of alloys supplied in extruded form from seven to four as an aid to economic production. The first big step was the development of a general purpose alloy known as AZ?21x covering all decorative and medium stressed applications, which will supersede two older alloys. Sales approaching a million feet in this alloy show that it bids fair to become the 'mild steel' of the magnesium industry, its applications ranging from terrazzo floor strip to textile machinery and television mast components. In the high stressed field, metallurgical features preclude low-cost extrusion of the older high-strength alloys, but recent development of a magnesium alloy containing zirconium promises an easily workable metal. Hitherto produced by expensive chemical additions, research now shows that the alloy can be produced by metallurgical means, which may make this alloy available for a wide range of commercial applications. Thus the future development programme for extruded products in the form of tube, bars, shapes, and structural angles and channels may evolve two alloys to cover all applications for strengths up to 52,000 lb. per sq. in. Such standardization is the result of taking advantage of the physical and metallurgical properties of high-purity magnesium instead of accepting techniques based on metal produced by older processes.

Jan 1, 1951

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Peter Heine

Diavik Diamond Mines Inc. (DDMI) has treated systems development as an integral part of the construction project when it built Canada?s second diamond mine. Fully aware that the proper collection and processing of operational data is needed to drive business decisions during production and planning, key Performance Indicators (KPIs) were defined to effectively manage operations when the mine went into production. The Production Information Management System (PIMS) allows KPIs to be measured, reported, and transferred to other systems in a reliable and convenient manner. PIMS provides a mechanism to collect real time production data from the various control systems around the site and acts as a tool to ?drill-down? and establish the important cause-effect relationships that impact the value of a KPI. Thus PIMS provides a data collection, storage, management, and an environment in which cause-effect relationships can be analysed and statistically verified. This understanding of the real cause-effect relationships, close to the source of the data and in the context of the operation, can be used to improve both operations and maintenance performance. The PIMS includes the PI Database implementation, its associated external interfaces with the various Control Systems, Cleaning Packaging Weighing System, Environmental System, Enterprise Asset Management (EAM) System, and Diamond Tracking System (DTS), as well as laboratory data collection, custom applications (downtime tracking, data reconciliation) and user clients. The interface with the EAM system provides material flow quantities and equipment availability on which the plant performance reports are based. The transfer of equipment usage to the EAM system is fed into the maintenance notifications and work orders functionality in the EAM. The environmental system interface provides the mechanism for capturing water consumption data required to generate the various regulatory reports. The interface to the cleaning-packaging-weighing system provides the mechanism for capturing batch data for transfer to the DTS for diamond product tracking at the production splitting facility in Yellowknife. The PIMS lab application provides a means of getting sample data into the system for critical metallurgical metrics, and the data reconciliation application provides a means of manually verifying the data before it is published or passed onto other systems.

May 1, 2003

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d'or"" analyse, dans une approche systémique, les travaux d'évaluation et de mise en valeur des gisements minéraux dans l'axe de la géologie, dans l'axée l'ingénierie et dans I ‘axe de l'économique. L’objectif est d'identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l'évaluation et de l'exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d'investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d'inventorie et de classification des réserves aux méthodes d'évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s'étendent qu’à l'axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l'information dans les axes de la géologie, de l'ingénierie et de l'économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d'évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s'inspire du Code australasien, peut facilement et rapidement s'intégrer dans les pratiques de l'industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l'échelle internationale. La proposition d'utiliser les marges d'erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu'une période de rodage."

Jan 1, 1992

By O. Herstad, J. M. Toguri, K. Grjotheim

DURING the last three years, investigations on the aluminum reduction of magnesium-bearing compounds have been initiated at the Institute of Inorganic Chemistry, The Technical University of Norway. The results of these investigations are reported in this paper. Very little information exists in the literature on the reaction between magnesium compounds and metallic aluminum. The available information itself is conflicting, and, to clarify the existing discrepancy, the reactions between aluminum and magnesium oxide (MgO), caJcined dolomite (CaO . MgO) and olivine (Mg2SiO.) were studied. The logical approach for the study of these reactions between condensed states with the formation of a gaseous phase is, ( 1) the measurement of the equilibrium vapour pressure of the gas, in this case magnesium, associated with the respective reactions and, (2) the identification of the end products of the reaction in order to establish the re-action scheme.

Jan 1, 1962

By L. Tong

The nickel laterite ore is composed of soft and hard minerals, and nickel distributes preferentially into the soft mineral rather than in the hard. Selective comminution of saprolitic and goethitic nickel laterites is investigated to upgrade nickel into the fine fraction using stirred milling. The optimal selective grinding conditions were determined through a kinetic study and the limit of selective grinding and nickel upgrade was analyzed. The breakage rates of minerals, grinding time, and the weight ratio of soft and hard minerals in the feed play an important role in selective grinding. A small breakage rate on hard minerals and a large breakage rate difference between the minerals are optimum for selective grinding. The soft mineral grade decreases with grinding time and the optimum grinding time is a trade-off of the soft mineral upgrade and recovery. The minerals weight ratio determines the limit of selective grinding. The effect of nickel upgrade is determined by both the conditions that influence selective comminution and the nickel grades in both the soft and hard minerals. The nickel grade in the soft mineral determines the limit of nickel upgrade.

Jan 1, 2015

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

By D. J. Zuliani

A mass and energy balance for a modern electric arc furnace ("EAF") indicates that about 70% of the process energy losses are contained in the off-gas as chemical energy in the form of uncombusted CO and H2 and as thermal energy. Given the magnitude of the off-gas energy losses, improved EAF energy efficiency needs to focus first on controlling furnace practice to maximize "in-EAF" energy utilization and second, on recovering residual energy in the off-gas existing in the fume system. This paper focuses on the application of off-gas analyzers, sensors and process models to control and optimize "in-EAF" energy utilization efficiency. The paper will also discuss the application of heat recovery technology to EAF steelmaking.

Jan 1, 2015

By R. E. Martin

"The Westerose Leduc (D-3) pool, a Devonian reef reservoir situated in Central Alberta, Canada, has now been producing for over seven years. As a unit operation, the pool pro-vides an interesting example of the full exploitation of gravity segregation tendencies. The reef has a 238-foot oil column, underlain •by bottom water and over-lain by a substantial gas cap. The original hydrocarbons in place were 147.96 million STB oil and 94.4 MMMCF of Taw gas cap gas. Nine-teen producing wells on 80-acre spacing have been completed, most of which are highly productive. Gas injection operations return solution gas to the gas cap. A study of the rock and fluid properties of the pool show it to be conducive to production by gravity segregation at high rates. Monthly average producing rates have varied between 800 B/D and 8,000 B/D and have recently totalled 3,000 BID to 5,000 B /D. Recovery and performance predictions under partial pres-sure maintenance at 10,000 BID indicate an ultimate recovery of 66 per cent of the original oil in place. In the absence of pressure maintenance, recovery would be only slightly less."

Jan 1, 1960

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By Peter Clevenstine

Minnesota Iron Ore Trifecta 1. World Demand 2. Industry Consolidation 3. Competitive Advantages

May 1, 2011

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956