Search Documents

By T. L. Tanton

Introduction Sturgeon River area, on the east side of lake Nipigon, Ontario, was the scene of a gold rush in 1934. According to press reports, the active staking during the latter part of the summer spread out rapidly from the early holdings until it embraced practically all of the lower basin of Sturgeon river in a belt up to ten miles wide extending west from Kinghorn for 35 miles to lake Nipigon. And, before winter set in, active prospecting and claim staking reached beyond lake Nipigon to areas where belts of ancient schists were known, notably west of Obonga lake. The writer's familiarity in past years with the areas to which attention has been directed admits of some observations on means of access in the field, the general geology, and the progress that has been made in identifying formations favourable for the occurrence of gold. Canoe Routes From the writer's observations in Sturgeon River area in 1917 and in the Obonga Lake area in 1933, it is recalled that there is, locally, a striking dif~ ference in the accessibility of the two areas by travel along canoe routes. Sturgeon River area is easily accessible from Kinghorn or Jellicoe stations on the Canadian National railways. Many small lakes, commonly of the linear type and with elongations east and west, occur among the forested rocky ridges near Jellicoe (Figure 1) and to the east and west along, or adjacent to, Sturgeon river. This stream has long stretches with gentle current between the falls and rapids. The drainage system provides excellent canoe routes (Figure 2), and the interruptions to travel (Figure 3) are remembered .as scenic features that were passed by portages with firm footing. West of Obonga lake, the streams flowing easterly to lake Nipigon may be followed through scenic canyons to a plateau of law relief characterized by extensive muskegs and shallow, brown-water lakes; and along small streams, where beaver dams have been destroyed, there are muck ponds where the usual alternatives of paddling or portaging can be dismissed in favour of the 'moosing' method of progress with the canoe (Figure 4).

Jan 1, 1935

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province's resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive' ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson's Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

By D. V. Krefting, D. R. Bennett

"The Cyprus Anvil Mining Corporation established a lead-zinc mine and concentrating plant at Faro in Yukon Territory in 1969. Following some 12 years of continuous operation from a single pit adjacent to the concentrator, the company decided to expand operations into two additional areas on the Vangorda Plateau. The two new deposits, known as Grum and Vangorda, are located some 15 kilometres from the existing concentrator.Confirmation of mining feasibility was followed by determination of the most practical and economical method of transporting the raw ore from the new mine sites to the existing concentrator. This analysis was carried out in two phases. The first phase reviewed the feasibility of alternative transportation systems on an 'order-of-magnitude' cost basis. This work identified systems worthy of more detailed examination. The second phase examined the preferred alternatives in greater detail.Initially, operating principles and parameters were established and catalogued. Then, based on these criteria, complete systems were developed utilizing alternative modes of transportation . In the overview analysis, some transportation modes were judged impractical and discarded, 'order-o f-magnitude' costs were developed for other systems and the most costly were eliminated . In the detailed study, the favourable systems were examined in depth which required development of accurate capital and operating costs, consideration of environ- mental impacts and an assessment of intangibles associated with the operation of a new development."

Jan 1, 1984

By Tobias Riedel, Peter Ay, University of Applied Sciences, Bianka Bade, Nicole Pausch, Bernhard Gemende, Florian Logsch, Matthias Leiker, Satyanarayana Narra, Claudia Glaser

This study focusses on the production of micro-structured agglomerates with high porosity from iron (III)-hydroxide-containing materials as adsorbent. A fractal-like structure of the agglomerates was created through a two-stage agglomeration process. Developing porous structures was necessary to increase the adsorption capacity. Various materials were used for the agglomeration experiments: i) filter cake (dry matter content 23 to 27 wt.-%); ii) FerroSorp®DGµ, a product which is already being used commercially for various applications in water cleaning. These materials in the pristine state have different characteristics such as dry matter content and particle size distribution. The desired optimised agglomerates can be achieved with the help of additives or binders, respectively. Additionally, the agglomeration process parameters play a vital role. In order to produce agglomerates with high porosity, the process was carried out in two steps. Firstly, FerroSorp®DGµ (d90 < 30 µm) was agglomerated jointly with the aforementioned filter cake in an Eirich intensive mixer (particle size range 125 µm < d90 < 500 µm). The second agglomeration step post drying was carried out in a pelletisation disc or in an Eirich intensive mixer with the addition of polymeric binders (up to particle sizes ranging from 2 to 4 mm). Agglomerates were characterised both in short and long term loading tests using phosphate as model ion. Contact times were less than 10 min, similar to practical application in percolation columns, or more than 7 days, respectively. The results show that the agglomerates produced in the two-stage pelletisation process have more advantageous properties like better accessibility of the active sites obtained by specificly influencing the particle size distribution during the two-stage pelletisation process.

Jan 1, 2016

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By J. D. Stewart

One of the first important questions that should be settled on the opening of a mine or the development of a new deep is the system of haulage to be used, since the layout of the haulage-ways at the pit bottom, or, in case of a slope mine, the arrangement of the surface works, depends largely upon the type selected. Should it later become desirable to install a system of haulage of a type other than that for which the mine roadways were originally laid out, considerable difficulty would likely be encountered in its installation and with the result that it would in all probability be most unsatisfactory and expensive in its operations. It therefore becomes very necessary that full consideration be given the haulage problem at an early date in order that the type best suited to the mine conditions and the required outputs can be intelligently planned for. It is sometimes found, however, that no matter how well the mining engineer explores the seam to be developed, or how accurately he anticipates its eccentricities, there will still remain some unrevealed or unsuspected conditions, or shall we say obstacles, placed by Nature to prevent the too easy winning of her treasures and incidentally to frustrate or modify the application of the plan so painstakingly laid down on paper, and to adversely affect the cost estimate.

Jan 1, 1928

By Ali Roshanfekr

Linear mine-waste dumps at open-pit mine sites essentially represent expedient places to deposit large quantities of waste rock. Being in valleys in most cases, the effect of the water flowing through and out of the deposit often raises questions about their hydraulic behaviour and geotechnical stability, especially the zone of the downstream toe. In order to provide better tools to assess the behaviour of these dumps a laboratory and analytical study was conducted. Firstly, physical models were built to assess the flow capacity and hydraulics associated with the linear growth of such dumps. It was found that the elevation of the point of first-emergence on the downstream side becomes constant after the dump grows to a certain length, but that the upstream depth concurrently increases. The limits of applicability of the theories of Hansen et al. (1995, 2005) are discussed in this regard. Secondly, in analysing the seepageface downstream, two approaches for solving this spatially varied flow (SVF) problem were undertaken. Under one of the approaches links to SVF depths were merely made to the hydraulic heads of the body (interior) and flux was calculated using conventional surficial nodes after the fact, Under the other approach flux nodes were used to link the SVF algorithm to the hydraulic heads further ?inside? the body of the rockfill. Although there are inherent uncertainties, it was found that these two methods can be made to perform equally well. Research continues but it appears that a linear variation in depth can be assumed without inducing any unrealistic exit gradients in the zone of primary concern with respect to unravelling.

May 1, 2011

By Hongyan Qu, Lihui Zheng

"Horizontal wells in coal seams, Qinshui basin, China are prone to wellbore instability problems induced by drilling, completion and production operations due to the presence of natural cleat network, anisotropy with regard to permeability, brittleness and mechanically weak property of the coal rock. The mechanism of wellbore instability in coal seams is very different from that in conventional formations, the traditional wellbore stability study methods therefore, are not proper for wellbore stability analysis in coal.In this study, the mechanism and controlling of wellbore stability of coal seams in the Qinshui basin was investigated through theoretical modeling, laboratory experiment and field operation. Firstly, a new physical model of wellbore stability for highly-cleated coalbed was proposed, considering the combined effect of mechanical mechanism and reservoir characteristics, specifically, taking the effect of reservoir pore pressure in the vicinity of the wellbore on the wellbore stability into account. Then experiments on the triaxial stress evaluation were conducted at laboratory where rock mechanical parameters such as Poisson's ratio, Young's modulus, compressive strength, tensile strength, angle of internal friction and cohesion ability were measured respectively. The in situ stress at different depths in four wells of Zheng 1-303, Zheng 1-308, Zheng 1-309, and Zheng 1-310 in the Zhengzhuang were calculated, and the collapse pressure and formation breakdown pressure were predicted through the theoretical model we developed. Finally, by comparing the maximum collapse pressure and minimum breakdown pressure of the four wells in the coal as well as in the roof and floor of the coal seams, the fluid weight window for safe drilling in each coal seams was determined, and appropriate approaches against anti-sloughing in coal seams, Qinshui basin were applied in the field operation.The wellbore stability was found not only related to the wellbore pressure, but also affected by the pressure in the reservoir through the theoretical model. The fluid weight window for safe drilling in each coal seams varies with the coefficient of wellbore stability in the model. The laboratory experiment results indicate that the roof and floor of 3 # coal in Qinshui basin has high breaking strength, high heterogeneity, and are easy to collapse and breakdown. In addition, the whole rock mineral analysis shows that 3 # coal in the Duanshi block has high clay content, resulting in the phenomenon of hydration swelling as clay encountered water, and leading to unstable coal and extreme large drilling uncertainties. Due to the effect of the unstable rock mechanical properties of the roof and floor formation on the wellbore stabilizing, drilling parameters, drilling fluid performance and BHA were optimized during the drilling process according to the formation properties, rock mechanical properties and drilling techniques in the field operation."

Jan 1, 2015

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Jas. E. Thomson

PUBLIC attention was first attracted to the Crow River area of north-western Ontario by the discovery of gold in 1928. The first three discoveries were eventually developed into Central Patricia, Pickle Crow, and Albany River mines. In 1929, preliminary developments were carried out at the Howell vein on N.A.M.E. (later Pickle Crow) claims, and in 1929 and 1930 surface and underground work indicated an ore-body at Central Patricia mine. However, due to the financial depression and the distance of these properties from the railway, it was not until 1934 and 1935 that, benefitted by the revaluation of gold, the real potentialities of these two properties began to be realized. Their immediate success led to a resumption of activity on neighbouring properties throughout the area in 1936 and 1937. Preliminary prospecting in the earlier period had been limited by the scarcity of rock exposures in the country. The procedure in the recent programme of intensive exploration has been along similar lines at most properties and has consisted lf detailed geological mapping accompanied by geophysical surveys and followed by systematic drilling of favourable zones. The present importance of the camp may be judged by the fact that, in 1937, Central Patricia and Pickle Crow mines together produced bullion valued at $3,662,953, and paid $1,450,000 in dividends. In addition, there were pro-mising gold developments at Albany River mine. During the past two seasons, the Geological Branch of the Ontario Department of Mines has been making a fairly detailed study of the geology and mineral deposits in the Crow River area. It is the purpose of this paper to present a brief statement of some of the structural features of these deposits; a summary of other geological information essential for the understanding of the main topic is included. A more detailed report on the area will be published shortly by the Ontario Department of Mines. It is impossible to make full acknowledgment here for all help received, for the writer is in-debted to the management, staff, and consultants of every Company in the camp for generous co-operation in the field and for information, plans, maps, and records placed at his disposal. Reports and articles on properties in the area have been written by Hurst (1), Cormie (2), Reid (3), and the staff of Pickle Crow Gold Mines ( 4).

Jan 1, 1938

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant&apos;s operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By R. Bonifaz, R. Subiabre

The Chagres Smelter, part of the Anglo American plc group, situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant review of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studied various options for investment that will yield a suitably profitable business to benefit both Anglo American and Chile. The most relevant technical indicators are: energy consumption=6,3 GJ/ton fine copper (1st in the world), intensity of smelting rate in Flash Smelting unit of 6,900 ton of copper concentrate/m2 of furnace area (1st in the world) and to be one of the top five smelters in achieving the lowest direct cash cost .

Jan 1, 2007