Search Documents

By Zorigtkhuu Davaanyam, Bern Klein, Stefan Nadolski, Amit Kumar

"The High Pressure Grinding Rolls (HPGR) is a relatively new comminution technology that has been shown to be more energy efficient compared to semi-autogeneous (SAG) mills. Full and fair consideration cannot be given to HPGR-based comminution circuits in early stage projects, because presently pilot scale testing is required for assessing and sizing; pilot scale testing requires bulk samples weighing more than one tonne. A CAMIRO research program was conducted at the University of British Columbia to develop bench scale tests that would reduce the quantity of sample required to assess HPGR.Three test procedures were developed.1. The Direct Calibration Methodology calibrates piston press test results to pilot scale test results such that piston press tests can then be used to determine the energy–size reduction relationship for a range of ore types.2. The Database Calibrated Methodology, which is similar to the Direct Calibration Methodology except that it calibrates piston press tests against a database of pilot scale and piston press tests.3. The Semi-Mechanistic Methodology was developed to use piston press test results as an input for an HPGR based energy-size reduction performance model.Through utilization of these methodologies, the energy–size reduction performance of an HPGR can be predicted with minimal sample requirement. In addition, piston press testing is far more cost effective, faster, and accessible than pilot-scale HPGR testing.IntroductionOne could argue that in the future, decisions regarding selection of comminution circuits will be made primarily on the basis of energy consumption. The following facts and predictions support the argument:"

Jan 1, 2015

By Heikki Laurila, Sirkka-Liisa Jämsä-Jounela, Jarkko Karesvuori

"Artificial Intelligence includes excellent tools for the control and supervision of industrial processes. Several thousand industrial applications have been reported worldwide. Recently, the designers of the A1 systems have begun to hybridize the intelligent techniques, expert systems, fuzzy logic and neural networks, to enhance the capability of the A1 systems. Expert systems have proved to be ideal candidates especially for the control of mineral processes.As successful case projects, an expert system based on on-line classification of the feed type using neural data analysis is described in this paper. The essential feature of this expert system is the classification of different feed types and their distinct control strategies at the plant. In addition to the classification, the expert system has a database containing information about how to handle the determined feed type. This self-leaming database scans historical process data to suggest the best treatment for the ore type under processing. The system has been tested in the Outokumpu Finnmines Oy, Hitura mine. Other projects have been reported to be in progress.INTRODUCTIONIn the past ten years considerable researches have been done in the application of artificial intelligent methods in process industry. The technologies of fuzzy logic, neural networks and expert systems have received several thousand applications worldwide: monitoring and analysis of process operations, fault diagnosis, supervisory control, feedback control and scheduling and planning of operations. Recently, the designers of these systems have begun to hybridize these intelligent techniques to enhance the current capability of expert system. Complex signal processing, neural networks, fuzzy logic and rule-based systems are also implemented to develop new so-called smart or intelligent sensors, actuators or components. Field buses are playing a more and more important role in automation systems and in imbedded systems. The development of field buses has allowed the distribution of smart components over networks."

Jan 1, 2000

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By Réjean Lévesque

SIDBEC-NORMINES a été incorporée en 1976. Depuis la fin de 1977, ses activités comprennent outre la concentration au lac Jeannine, près de Gagnon, du minerai de fer extrait du gisement du lac Fire, I'exploitation d'un atelier d 'enrichissement secondaire et une usine de bouletage à Port Cartier. L 'objectif principal de SIDBEC-NORMINES est de produire six millions de tonnes de boulettes d'oxyde de fer par année, dont trois millions auront une faible teneur en silice afin de répondre aux exigences de la réduction directe. Les installations de SIDBEC-NORMINES sont adjacentes aux installations portuaires de la Compagnie Minière Québec Cartier, à l'est de la ville de Port-Cartier. L 'ensemble est conçu pour produire les deux types de boulettes avec deux circuits d'agglomération installes en parallèle. La production de concentré enrichi (68% Fe et plus) est obtenue dans une usine d'enrichissement utilisant le precédé de séparation magnétique hum ide ahaute intensite (separateurs Jones). À l'usine de bouletage proprement dite, on effectue Ie broyage du concentré et sa mise en boulettes sur disques; l'in duration des deux types de boulettes est obtenue sur deux chaînes d'agglomération Dravo dont chacune a une capacité annuelle nominale de trois millions de tonnes.

Jan 1, 1979

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By R. Clarkson

"The Yukon's numerous (185) placer gold mines are still a major social and economic force in this developing economy. Gold recovery at each of the various sluiceboxes is not optimized due to extremely difficult sampling logistics and a shortage of technical expertise and industrial research.At each of six operating placer mines, numerous sluicebox tailings samples were collected with hand held sample cutters and combined into large (2-7 cubic yards) duplicate samples. The entire sample volumes were screened and processed on a shaking table to determine gold losses. The existing and potential gold recoveries and recommended sluicebox design and operating parameters are presented.2 ACKNOWLEDGMENTSThe Project Manager gratefully acknowledges the following support for this placer research program:The funding received from the National Research Council's Industrial Research Program, the Canada/Yukon Economic Development Agreement and the Canada Center for Minerals and Energy Technology (CANMET): andThe technical advice provided by Tad Cienski (CANMET), Ron Johnson (KPMA), George Poling (University of B.C.) and Dan Walsh (University of Alaska).3 OBJECTIVESThe objectives of the Gold Recovery Project are to: evaluate gold losses with statistically based sampling programs; determine how to improve gold recovery; assist miners with the recommended technology and make this information available to the entire placer industry."

Jan 1, 1990

By H. Sahay

This paper summarizes the history and ore-grade statistics of mining the Ming orebody, and then details the mining methods. Included are raising, stoping, drilling and blasting techniques. Particular attention is paid to ground support, ventilation and pumping requirements.

Jan 1, 1979

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By D. W. McDonald, L. M. Heaman, R. A. Creaser, T. Davies, T. Chacko, A. Simonetti

"The Three Bluffs gold deposit is located in the Committee Bay greenstone belt, which forms part of the Rae domain of the western Churchill province, Nunavut, Canada. Gold mineralization is hosted by iron formation of the Neoarchean volcanosedimentary Prince Albert Group, and is associated with silicification (quartz veining) and sulfidation of magnetite and other Fe-rich minerals. Conventional U-Pb zircon dating of a conformable dacite unit within the volcanosedimentary host-rock sequence and a crosscutting diorite intrusion confirm a ~2.7 Ga age for deposition of the supracrustal package. U-Pb monazite dates and Pb isotopic analyses of sulfides were obtained by laser ablation-multicollector-inductively coupled plasma-mass spectrometry (LA-MC-ICP-MS). A subset of U-Pb monazite (1813.8 ± 8.7 Ma) and Re-Os arsenopyrite (1822 ± 21 Ma) dates, combined with a Pb-Pb secondary errorchron age for pyrite and arsenopyrite (1829 ± 77 Ma), suggest that gold mineralization associated with sulfidation of the iron formation occurred at ~1815 Ma, prior to high-grade (upper amphibolite facies) tectonometamorphism in the Three Bluffs area (D2TB/(M2TB). An ~1815 Ma age for deposit formation is broadly consistent with evidence from elsewhere in the western Churchill province and to the southwest in Manitoba and Saskatchewan for a late Trans-Hudson (1.9-1.8 Ga) gold mineralizing event. The majority of U-Pb monazite ages form a second population at 1780.6 ± 4.2 Ma, similar to the age of the majority of Re-Os arsenopyrite analyses (1763 ± 11 Ma). These dates are thought to reflect the timing of peak M2TB metamorphism. 40Ar/39Ar dating of amphibole, biotite, and muscovite yielded plateau ages ranging from 1723.8 ± 9.0 Ma to 1710 ± 17 Ma, which are interpreted to record the timing of postpeak metamorphic cooling to below the respective closure temperatures for Ar diffusion in these minerals. Le gîte aurifère de Three Bluffs est situé dans la ceinture de roches vertes de Committee Bay, laquelle appartient au domaine de Rae dans l’ouest de la province de Churchill, au Nunavut, Canada. La minéralisation aurifère est encaissée par des formations de fer d’âge Néoarchéen appartenant aux roches volcanosédimentaire du Groupe de Prince Albert; la minéralisation est associée à de la silicification (veines de quartz) ainsi qu’à la sulfidation de la magnétite et d’autre minéraux riches en Fe.Les résultats de la géochronologie U-Pb conventionnelle sur une unité de dacite concordante au sein de la séquence volcanosédimentaire ainsi que d’une intrusion de diorite qui les recoupe indiquent que ces roches supracrustales ont un âge de ~2.7 Ga. Les âges U-Pb de la monazite ainsi que les analyses des isotopes du plomb des sulfures ont été obtenus par ablation laser (LA-MC-ICP-MS). Certains des âges U-Pb obtenus à partir de la monazite (1813.8 ± 8.7 Ma) et des âges Re-Os retournés par l’arsénopyrite (1822 ± 21 Ma), en association avec l’âge indiqué par une isochrone à données dispersées « errochron » secondaire Pb-Pb pour la pyrite et l’arsénopyrite (1829 ± 77 Ma), suggèrent que la minéralisation aurifère associée à la sulfidation de la formation de fer s’est formée vers ~1815 Ma, avant que l’événement tectonométamorphique (D2TB/(M2TB) de niveau élevé (faciès des amphibolites supérieures) affecte le secteur de Three Bluffs. Un âge de mise en place de ~1815 Ma pour ce gîte est compatible avec les données en provenance de l’ouest de la province de Churchill ainsi que plus au sud-ouest au Manitoba et en Saskatchewan qui indiquent la mise en place de minéralisations aurifères à la fin de l’orogénèse Trans-Hudsonienne (1.9-1.8 Ga).La majorité des âges U-Pb de la monazite constituent une seconde population formée à 1780.6 ± 4.2 Ma, ce qui est similaireLà l’âge obtenu pour la plupart des analyses Re-Os sur l’arsénopyrite (1763 ± 11 Ma). Ces âges reflètent probablement l’atteinte du pic métamorphique M2TB.La géochronologie 40Ar/39Ar de l’amphibole, de la bio"

Jan 1, 2009

By Sylvie Brassard

Available information ?? InfoMine: mineral properties ?? Metals Economics Group: budgeted exploration expenses ?? MineScan: Canadian and American Mining Companies ?? Statistics Canada: Canadian Direct Investment Abroad, by Sector in the world OR all sectors by Country

May 1, 2008

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By B. Hilscher, P. Nayak, N. Yoon

"The mining industry is currently facing challenges with declining feed grades and is struggling to find solutions to improve the project’s economic value. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed.This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include two underground and two open pit mines that are base metal and precioius metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed.The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include, X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS).IntroductionOre sorting is a sensor-based sorting technique introduced between the excavation stage and processing stage, where the unwanted waste is diverted to the waste dump and only the ore is sent to the mill for further processing. As a result, the quality of the material entering the mill is improved and the dilution of the ore is reduced. In greenfield projects, sensor-based ore sorting provides an opportunity to reduce the capital cost of the project and increase the return on investment (ROI). With most operations currently facing the challenge of finding a high grade deposit, having a sorting unit provides several advantages while keeping the cost at minimum."

Jan 1, 2017

By P. Keating, J. Goutier, J. Ayer

"New, high-resolution geophysical surveys were undertaken over parts of the Abitibi Subprovince, Canada, to help with geological mapping and to promote mineral exploration. Gravity surveys in the Rouyn-Noranda and Matagami areas (Québec) allowed better 3-D mapping of important geological structures, and a multiscale edge analysis of ground gravity data over the Blake River Group confirms that major faults behave at depth as predicted by surface geology. Airborne gravimetry west of Matagami (Québec) helped to identify a new trend south of Lake Grasset that is almost perpendicular to the assumed geological trend of the area. Electromagnetic (EM) surveys, flown in the Chibougamau (Québec) and Bartlett Dome (Ontario) areas, allowed new conductors to be identified at greater depths than were achievable with previously used EM systems. Airborne magnetic surveys were flown in the Burntbush area (Ontario), and other available high-resolution magnetic data were compiled to produce a continuous and homogenous magnetic grid of the Abitibi region.The resulting compilation map clearly shows the locations of dikes, faults, and shears zones, and reveals some fault extensions in areas of extensive overburden. This grid also allows the computation of enhanced maps, such as vertical derivative and tilt maps (e.g., a tilt map shows subtle magnetic features in the Blake River Group that are difficult to see in the total magnetic field or its first derivative). Results from these new surveys show there is considerable value in (1) resurveying areas covered by older surveys, and (2) recompiling data sets from these older surveys."

Jan 1, 2012

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005