Search Documents

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992

By A. Ghahreman

Activated carbon is proven to be able to catalyze arsenic oxidation in aqueous solution under acidic conditions. A commercially available granular coconut shell based activated carbon (AC) has been evaluated for catalysis of arsenic oxidation in this study. The rapid small-scale column test (RSSCT) has been developed to simulate and predict the performance of a carbon-based arsenic treatment system in a pilot scale reactor. Effects of residence time, aeration rate, and initial arsenic concentration in the influent solution on the AC catalysis of arsenic oxidation under dynamic and continuous conditions were studied by manipulating these parameters during RSSCTs. The effectiveness of the AC on arsenic oxidation was examined over the course of constant diffusivity based RSSCT operation. Residence time and initial arsenite concentration are proven to be the most effective impacting parameters on the arsenic oxidation process. For the 218 min residence time, the highest steady-state arsenic oxidation efficiency achieved was 98% with 1 g/L As(III) being treated at pH=1 under 0.05 L/min oxygen aeration. In a long-running RSSCT, the oxidation efficiency did not seem to deteriorate over a course of 666 hours operation, corresponding to 13986 mL total influent throughput volume. INTRODUCTION Arsenic is toxic to both animals and plants and inorganic arsenicals are proven carcinogens in humans. The increased extraction of low grade and complex mineral resources has introduced high ratios of arsenic into metallurgical processes. Discharge of arsenic by acid mine drainage resulting from mining activities has added intensive pressure on the need for proper treatment (Lawrence & Higgs, 1999). Since trivalent arsenite is more toxic and has lower affinity to solid surfaces for adsorption, many treatment systems initiate with an oxidation step to convert arsenite to arsenate and reach the ultimate immobilization of arsenic by the following precipitation of arsenate (Nazari, Radzinski, & Ghahreman, 2016). Scorodite precipitation has been studied extensively as a means of arsenic immobilization due to its high stability and negligible potential of releasing arsenic (Filippou & Demopoulos, 1997). As a stable ferric arsenate mineral, crystalline scorodite can contain up to 30 wt% arsenic (Paktunc, Dutrizac, & Gertsman, 2008). Arsenic must be in its pentavalent oxidation state in order for scorodite to be precipitated via oxidizing ferrous ions (Clancy, Hayes, & Raskin, 2013).

Jan 1, 2019

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By R. E. Whitehead

"The earliest gold-mining operations in Ontario included the Cordova, Deloro, and Sophia mines north of Lake Ontario (see for example, Miller and Knight, 1914). The Cordova deposit, worked intermittently between 1891 and 1940, is reported to have yielded 22 774 oz of gold from 127 670 tons of ore averaging 0.19 oz/ton Au (Gordon et al., 1979). The property remained inactive for many years. In 1988, Gunnar Gold Inc. and Mill City Gold Inc. conducted a drilling program along the main Cordova vein. The present study is based on core from three drill holes through the Cordova gabbro (Fig. 1) and the carbonate alteration zones enveloping the quartz-carbonate veins. The relatively narrow width of the alteration zone and the availability of continuous sections of core provided an opportunity to conduct a compact mineralogical-chemical study of carbonate alteration and its effect on the redistribution of rare earth elements (REEs). Although the Cordova deposit is not of great economic importance, this study has revealed a number of interesting features which are interpreted as resulting from processes that may be applicable to gold-bearing quartz vein deposits elsewhere.The Cordova gabbro is layered in places, varying from fine-to coarse-grained and in color from light gray (feldspathic) to dark gray-green (amphibolitic). However, layering within the section of the gabbro considered here and which hosts the Cordova gold deposit is mainly textural rather than compositional. Samples of unaltered gabbro selected for analyses were medium- to coarse-grained; amphibolitic and anorthositic phases were avoided as being less representative of the general chemical composition of the gabbro.The Cordova intrusion has undergone regional metamorphism and consists dominantly of actinolite and saussuritized plagioclase with smaller amounts of granular clinozoisite and flaky chlorite; minor quartz, ilmenite, titanite, apatite, and calcite are typically present. Some actinolite grains have irregular rims of pleochroic green hornblende that is optically continuous with the actinolite. Both chlorite and clinozoisite occur in two modes. Chlorite occurs as an alteration product of actinolite and as separate grains in the groundmass. Clinozoisite and albite occur together as regional metamorphic alteration products of original plagioclase crystals and as discrete grains in the matrix.The main gold-bearing quartz-carbonate occurrence occupies an easterly trending, steeply southward-dipping carbonatized shear zone up to 15 m wide and 700 m long. The gold occurs principally in irregular lenses and veins of quartz-carbonate up to a foot thick occupying the lower part of the schistose shear zone within the gabbro. This zone consists of chlorite, biotite, and carbonate and is flanked on both sides by chlorite-carbonate schist lacking biotite. The chlorite-carbonate schist in turn grades into regionally metamorphosed actinolite-bearing undeformed gabbro.The dominant sulfide within the quartz-carbonate lenses and in the surrounding schist is pyrite which occurs mainly as small cubes (1 mm to 2 mm) generally making up less than 10% of the rock. Rare blebs of chalcopyrite are present. Magnetite is common throughout the schist."

Jan 1, 2001

By C. F. Harris

Following the initial development of the zinc-lead blast furnace, efforts have been directed both at increasing the scope of the process and increasing the cash return. The paper reviews the process developments which enable the process to smelt efficiently a range of material which encompasses high-grade zinc sulphide concentrates. mixed concentrates, Waelz oxide, zinc ashes and other materials blended to give a furnace feed ranging from 25 to 65% zinc and from 1 to 25% lead, with a copper-lead ratio exceeding 1 to 8. The paper also reviews the process developments which have enabled the capacity of a furnace and condenser system of standard size to be boosted from 30,000 to 80,000 tonnes/annum. The benefits achieved are used as a justification for continuation of the development of the zinc-lead blast furnace. Predictions are made of the benefits expected from further developments.

Jan 1, 1979

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract—Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O signature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2&apos; r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By T. L. Tanton

"The New Helen mine is 12 miles east of Michipicoten harbour on lake Superior. It is 2 miles east of Wawa station, on the Algoma Central railway, with which it is connected by a spur line railway and a highway.The mine was discovered by Ben Boyer in 1898 during the gold rush near Wawa lake, Ontario. The original discovery was of solid hematite ore extending to a height of 100 feet on a hill rising abruptly on the east side of Boyer lake. The property was acquired by the Algoma Steel Corporation and mining was commenced in 1899. The first iron ore was shipped in 1900. The mine was operated until 1918 when the hematite became exhausted at a depth of 800 feet below Boyer Lake level.Drilling at the Helen mine, after 1910, revealed a large body of siderite both below and to the east of the hematite. By 1913, the body was known to be about 200 feet wide, 3,000 feet long, and at least 2,200 feet deep. In this there was estimated to be 100,000,000 tons of proved and probable siderite ore. An adit was driven into this body in 1917, and in 1918 work was suspended. In 1937 the Algoma Steel Corporation proceeded with the development of the New Helen mine by open-cut mining, and the beneficiation of the ore by sintering. Production commenced in 1939 and has since been maintained at the rate of approximately 500,000 tons a year.From 1900 to 1918, inclusive, the total production from the Helen mine was 2,823,369 tons of hematite ore and 51,930 tons of pyrite. From 1939 to the end of 1945 the total production from the New Helen mine was 3,921,455 gross tons of siderite ore.GEOLOGYThe Helen property is underlain by rocks of Precambrian age. For general description, and a statement on the structure of the iron deposits, the map-units are those shown in Fig. 1.The oldest rocks occur in a complex that lies north and south of an east-west trending zone, 1 ½ miles long and ¼ mile wide, in which the iron deposits occur. That part of the complex lying south of the iron deposits includes small masses of altered conglomerate and slate, and greenstones and pyroclastics. Other fairly abundant rocks are sericitic, chloritic, ottrelitic, and carbonatized schists of doubtful origin, and almost massive metamorphic rocks in which a development of carbonate, ottrelite, quartz, and other minerals has obscured a pre-existing schistose structure. Felsite and quartz porphyry are· prominently exposed south of the iron deposits."

Jan 1, 1954

By Euler M. De Souza

"This paper presents a study developed to assess the potential use of salt tailings as backfill to control surface subsidence and as a mine bulkhead used to isolate areas of potential brine inflows. A series of index tests, centrifuge model tests and quasi-static creep consolidation tests were performed to evaluate the creep and consolidation properties of salt backfl1l and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. The centrifuge models were specifically designed to study the mechanical behaviour of salt backfill under the influence of brine inflow and long-term creep. Test results indicated that salt tailings could be applied underground as a bulkhead to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. It is hoped that this study will assist mine planners to develop contingency plans to control brine inflow occurrences. IntroductionThe use of salt tailings as backfill is a technique that would assist in the control of potential brine inflows and surface subsidence, and would have a very positive impact on the long term adverse environmental effects associated with surface salt tailings disposal. A centrifuge testing program was designed to evaluate the behaviour of salt tailings as backfill; the effectiveness of salt backfill as a bulkhead used to isolate areas of potential brine inflow and the potential use of salt backfill to control surface subsidence. The testing program was also used to evaluate the creep-consolidation properties of salt backfill and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. This paper presents the results of the experimental centrifuge testing program and a comparison of results with models tested under I g using an electrohydraulic servo-controlled loading frame (MTS) and a creep consolidation cell. Applicability of the results to practical underground soft rock mining is also discussed.The centrifuge model tests indicated that salt tailings could be applied underground as bulkheads to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. Because the applied stresses (1.2 MPa) and fill consolidation were relatively low, the centrifuge simulated bulkhead did not retain all of the inflow brine. At typical field stresses it is expected that the fill would be able to seal off panels with brine inflows. Further testing at higher stresses are suggested to determine the consolidation and stress levels at which the fill would completely retain any potential brine inflow head and positively act as mine bulkhead."

Jan 1, 1994

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By Herbert D. Drechsler

"THE FOLLOWING are some comments on the article, ""International Trade in Minerals and Economic Development"", by M. Sengupta, published in the October 1976 issue of the CIM Bulletin.Sengupta says in the introduction that ""The mechanism through which this growth (economic development) has occurred is basic ally straight forward"". His statement is quite misleading and perhaps it is better to quote Gerald Meier:""Development economists must operate in an imperfect second-best world, away from the simplified premises of neoclassical economics. Their subject matter is therefore not yet a coherent or self-contained discipline. Denied recourse to a set of general principles, perhaps the student's most sensible introduction to economic development is through a study of 'leading issues' that are at the time a major preoccupation of the development economist and development practitioner"" .Sengupta quotes an authority who wrote 18 years ago. Academic and operating development economists today know full well that existing theory is quite deficient. Sociologists, political scientists and engineers in this field also know that economic, social, political and technical development involves all academic disciplines.Sengupta indicates that tariffs in developed countries prevent less developed countries from supplying refined metal, or manufactured and semi-manufactured products. He lists Zambia, Chile and Zaire as examples of copper concentrate exporters, as inadequately shown in Table 1. He is wrong."

Jan 1, 1977

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014