Search Documents

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By Jean-Yve Tremblay, Michel Prud'homme

"IntroductionIndustrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors.At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2.Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties.The Industrial Minerals Industry in CanadaCanada has a large industrial minerals base and is a world leader in the production of some of them. The total value of product ion of these minerals has grown by 115% over the last 10 years despite the misfortune of asbestos.Industrial minerals have shown remarkable growth in the past 20 years at an average annual rate of 9.2%, compared to 7.8% for metallic minerals. In 1986, the value of industrial minerals rose to $4.9 billion, or 14% share of the Canadian mineral production. Figure I shows the value of production of the mineral industry for the period 1966-1986.The leading segment in industrial minerals segment since 1976 is the chemicals and agro-chemicals sector which has an average annual growth rate of 5.75 % in terms of value of production. During the same period, the growth rate for the whole Canadian mining industry was 1.37% per annum. The chemicals and agro-chemical s sector increased its contribution to the total value of production of 2% to 6070 despite the growing share of fuel minerals with 59%."

Jan 1, 1988

At 14%, the representation of women working in the mining industry is the lowest among primary industry categories in Canada1. With reference to mining operations and senior leadership, the gap in the industry is even more pronounced. In an effort to narrow the gender gap, recent industry, education, and policy efforts have been made to increase the number of women entering the industry through career awareness and early career recruitment strategies. These strategies implied that by increasing the numbers of women entering the industry there would be a natural progression of women into the hierarchies of organizations. Efforts to retain women in the industry have focused around removing career barriers such as reviewing flexible work practices and programs directed at work life balance. At this time, these efforts have resulted in negligible fluctuations to the gender gap within the industry. This research investigates the under-representation of Highly Qualified Women (HQW), and the interaction of workplace culture on their career advancement and retention within the industry. HQW (women with a bachelor?s degree or higher) are the focus of the work as they represent an essential source of leadership and technical capacity for mining organizations. This paper is based on the results of a survey of 170 HQW working in the Canadian mining sector. The findings from this research suggest that HQWs careers in mining are stalled, despite a strong indication by respondents of interest in their professional career advancement. With regards to workplace culture, respondents indicated that blatant forms of gender discrimination have been reduced in mining workplaces; however, exclusion from informal networks, implicit bias and subtler forms of workplace discrimination persist. Utilizing a framework to assess the workplace culture for women in attracting and retaining their employment, respondents provided detailed information on the aspects of workplace culture that are most problematic in relation to women?s career development in mining. Women consistently identified problematic workplace culture as a significant barrier to the career advancement and retention of women within the industry. The representation of women within the labour force will likely remain stagnant until the industry addresses workplace culture within the industry, and makes strategic efforts to develop inclusive cultures throughout mining and supportive organizations.

Aug 1, 2013

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By P. Ramirez

"To achieve an optimal metallurgical performance in the flotation process the bubble diameter should be between 0.5 and 2.5 mm. To control bubble size, frothers are added, reducing bubble size and conferring bubble stability against coalescence. However, the bubble generation mechanism determines predominantly the bubble size distribution produced. In mechanical flotation cells, bubbles are produced by the shear stress generated by a rotating blade on a gas stream. This mechanism produces a log normal bubble size distribution. In contrast, in column flotation, jetting gas injectors are commonly used in Chile and the bubble size distribution is bimodal with small and large bubbles. Bubbles larger than 2.5 mm mean a loss in surface area, while bubbles smaller than 0.5 mm move with the pulp stream and therefore collide less frequently with particles. In this paper, a new device based on a jetting sparger and a deflector disc (impinging jetting) is evaluated as an alternative sparger for column flotation.The new device was tested in a rectangular acrylic cell 1 m × 0.5 m × 3 m. High-speed cinematography was used to compare bubble generation with jetting and impinging jetting at different gas velocity in the nozzle (5–50 m/s). From the image analysis, it was observed that the deflector induces a shear stress, in analogy to a rotating blade but in this case the shear results from a high velocity gas hitting a static surface. The device was evaluated in a 0.5 m diameter 3 m high column. The McGill bubble viewer technique was used to compare the bubble size generated by jetting and impinging jetting. It was found that the Sauter mean bubble diameter reduced from 7.4 mm to 2.8 mm, when the jetting sparger was modified with the deflector. In the case of the impinging jetting sparger, 70% of the bubbles were in the effective range for flotation, while for the jetting sparger, only 10% were in the effective range."

Jan 1, 2016

By R. S. Jr. Stronach

"IntroductionThe property of Campbell Red Lake Mines, Limited, is in Balmer township, Red Lake area, Patricia portion of Kenora district, Ontario. It consists of a group of twelve claims which had been staked and re-staked a number of times before George W. and Colin A. Campbell staked them in 1944. Messrs. Brewis and White incorporated Campbell Red Lake Mines, Limited, in July, 1944, to acquire these claims from the Campbell brothers, and in November of the same year re-assigned their option on the controlling interest of the treasury shares to the Dome Exploration Company (Quebec), Limited, a wholly owned subsidiary of Dome Mines, Limited.A long known exposure of sulphides on the northeasterly portion of the property, which returned low gold assays, on sampling, was the only showing of interest at this time. However, Dr. H. C. Horwood's report and map of the district had recently been published and favourable structure W3.S indicated in Balmer township. It was on the strength of this showing and Dr. Horwood's report that Dome Exploration became interested in the property.Between. January, 1945, and April, 1946, a diamond drilling programme was carried out, with completion of sixty-one holes. Five holes proved the surface showing to hold no commercial interest, so routine cross-sectioning of the property from north to south was started. The fourth hole of the series returned excellent ore intersections and from that time on the programme changed to one of extending these values. The final results of the drilling showed that what is now known as the A zone has a continuous length of some 1,200 feet, a width of 4½ feet, and an overall grade of about 0.5 oz. gold per ton. There were many other intersections of ore grade outside this A zone which could not be successfully correlated .at that time, but underground work has opened many of them. It may be said here that practically all the work to date has been confined to the southeast claims of the property."

Jan 1, 1950

By W. W. Weber

"The Mine property comprises some 700 acres in ranges VI and VII, Barraute township, about thirty-seven miles due north of Val d'Or in northwestern Quebec.The transformation of a small farming community into the youngest and largest zinc producer in eastern Canada began late in the autumn of 1950. At this time, a geological survey party of the Quebec Department of Mines discovered sphalerite-pyrite mineralization in a strong regional shear structure crossing range VII of Barraute township. Diamond drilling commenced in November 1950, and by June 1951 a total of more than 63,000 feet of drilling, at fifty-foot intervals, had explored an ore zone 2,500 feet in length and 102 feet in average width to a depth of 700 feet, the deepest ore intersection.Production started late in 1952, and is at present in excess of 4,000 tons per day. Production in 1954 of77,790, 166 lbs. of zinc and 989,610 oz. of silver, from 1,525,284 tons of ore, makes this mine the largest zinc producer in eastern Canada.General GeologyAll the consolidated rocks of the area are Precambrian, and most of them are volcanic. They consist mainly of subsiliceous Javas, with smaller amounts of siliceous to intermediate lavas and pyroclastic rocks. The lavas have been intruded contemporaneously by many sill-like bodies of coarser-grained diorite and gabbro. There are no sedimentary rocks within ten miles of the mine.A period of major folding and faulting was followed by intrusion of granite. The volcanic rocks have been compressed into isoclinal folds trending roughly east-west, and the granitic batholiths also show a rude lineal alignment in the same direction. The granitic masses vary consider-ably in composition, ranging from the potassic LaCorne granite, ten miles south of the mine, to the sodic Duverny mass, ten miles west. In addition there is a variation from a general granitic core to dioritic and gabbroic phases on the margins and in satellitic intrusions."

Jan 1, 1949

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers' requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today's mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer' s changing requirements, government regulation s and increased manufacturer' s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979

By K. MacMaster

"This paper deals with the history, development, present and future of the Employee Assistance Programs in place at the Inco Ltd. operations in Thompson, Manitoba. It should be noted that, although many similar programs exist in various industries and jurisdictions, these programs had to be fine-tuned to meet the needs of Inco employees, having in mind the helping professional resources available in Thompson and its geographic location. IntroductionIn the late 70s, many Canadian industries and the Canadian Labour Congress and their affiliates commenced discussions on the value of the Employee Assistance Program (E .A.P.) philosophy to both management and labour.In the contract signed between Inco Ltd., Manitoba Division and Local 6166, U.S.W .A. in 1981, a commitment was made to establish a joint E.A.P. for the hourly workforce in Thompson, Manitoba. With this background and sequence of events in mind, it is appropriate to explain the methodology and the steps that were taken for the implementation of the hourly program. Development of Hourly ProgramIt was agreed by the company and the union that the committee to develop the program should consist of equal numbers from both sides: three active union members plus an advisor representing the Union and three supervisory personnel plus an advisor representing the Company; in addition, a person familiar with E.A.P.s from the Alcoholism Foundation of Manitoba was to act as a facilitator. The Union appointed a social worker who was working as a counsellor for union members as their advisor , and the company appointed a staff employee who had worked voluntarily in the field of alcohol and drug abuse for many years. The makeup of the committee was extremely important in order to give credibility to the entire process. The makeup of the committee is shown in Table 1.The facilitator selected from the Alcoholism Foundation of Manitoba was well known in the community and highly respected in his profession."

Jan 1, 1989

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By John Lamb

"The French Mine (formerly the Oregon) is 4 miles by road south of the Nickel Plate Mine. It lies on the steep eastern slope of the Similkameen River valley at elevation 4,000 feet, between Cahill and Winters Creeks.The property was discovered in .1901 and bought 4 years later by Messrs. French and Deardorf. It was developed in a modest way by the owners and by several companies until 1947, without success. The spectacular showings of bornite and chalcopyrite in the outcrop drew attention to its possibilities for copper rather than gold. Diamond drilling by the owners in 1947 yielded several high-grade gold intersections and created new interest. In 1949 the property was purchased by Kelowna Mines Hedley Limited. Exploration drilling and geological mapping outlined sufficient ore to commence production in 1950. Except for a few months each winter the operation has been continuous, and to the end of 1954 had produced almost 30,000 tons of high grade ore. The ore is crushed at the mine and hauled 8 miles by truck to the Company mill at Hedley, where it is treated together with the ore from Nickel Plate.Regional GeologyThe country rock consists of brown tuff, flows, limestone, and cherty formations belonging to the Nicola group (Rice 1947) of Triassic age. West of and just below the mine is a large mass of granodiorite which is part of the same body that underlies Nickel Plate Mountain. Bedding attitudes in the mine area are locally complicated, but dips are generally less than 45 degrees. To the south and below the mine the beds stand almost vertical, continuing downward with this attitude for 2,000 feet to Winters Creek. The main granodiorite contact is also steep, conforming to the sedimentary formations, whereas northward towards Nickel Plate it dips gently to the northwest, slightly flattter than the thick westerly dipping pile of sediments above it. The interpretation of this structure by Billingsley (1936) is that the French mine lies near the crest of the large northeasterly trending asymmetrical anticline which contains in its gently dipping western limb the Nickel Plate orebodies. The granodiorite body conforming roughly to this shape seems to occupy the core of the anticline. Sill-like prongs of granodiorite extend upward to the east from the main mass, outcropping over wide areas at the head of Winters Creek (Figure 1). There is a possibility that overthrusting from the west, similar to that on Nickel Plate Mountain, occurs not far below the French mine.An interesting feature of the granodiorite-sediment contact is that where it dips gently westward no alteration exists in the sediments, but where it has a steep front pronounced heat effects are indicated by the presence of a thousand-foot-wide zone of reddish garnet skarn."

Jan 1, 1949

By Avinash Kandalam, Markus Reuter, Jörg Kleeberg, Michael Stelter

The Top Submerged Lance (TSL) technology has obtained significant importance in the pyrometallurgy industry for nearly four decades. One of the advantages of TSL furnace is its high reaction rate, which is caused by splashing and turbulence of the melt. In contradiction, this phenomenon stands as a barrier for conducting experimental investigations to validate the simulation models. The highly turbulent and splashing environment in the TSL furnace is caused due to the immersion of the lance into the slag layer and thus the effect of the flame structure is directly related to the splashing, turbulence, reaction kinetics and life-span of the lance. Moreover, the material properties such as viscosity, density and the surface tension will also influence the flame structure. As a first step to understand the flame structure, attempts are made to generate a stable flame of the lance in an open environment. INTRODUCTION Top Submerged Lance (TSL) technology was invented during the 1970s at Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia by Floyd and Denholm. This technology was later commercialised and currently, there are about 100 TSL plants around the world commissioned by various licence holders such as AUSMELT (Outotec) and ISASMELT (Xstrata- Glencore Technology). Copper is the most produced non-ferrous metal followed by lead and zinc, see Hunt (2005). Today, a wide range of primary, secondary, and complex recycling materials are used as a feed material in the TSL, Alvear et al. (2010), Kaye et al. (2008). The working principle of TSL technology lies on inserting and submerging a lance from the top of a vertical cylindrical chamber into the slag layer. The lance is considered as the heart of the furnace, where the air and fuel are transported through two concentric tubes and are mixed in a combustion chamber, which is approximately 7 cm from the tip of the lance (considering the pilot-scale TSL furnace at the Institute for Nonferrous Metallurgy and Purest Materials - INEMET). The TSL furnace is very flexible with the type of fuel, feed material and the air input. The fuel can be natural gas/heating oil/fine coal particles and the air could be enriched with oxygen (Figure 1). The general mechanism of the TSL furnace lies on feeding the material from the top of the furnace and the material is pulled into the molten bath due to the high turbulent atmosphere, which results in high reaction rates. The thermocouples installed in the furnace (i.e. in the ceramic linings) allow the operator to know the temperature of the melt. For example, in the case of copper production the tapped material (i.e. matte/metal) can be transported to a settler for further processing or directly used.

Jan 1, 2019

By A. A. Ruitenberg, C. J. Morrissy

"The Lake George antimony deposit comprises a system of stibnite-bearing quartz veins that cut Silurian greywacke and slate. The stibnite-bearing ore zone is in part enveloped by a uraniferous zone.The ore-bearing quartz vein system occupies an easterly striking, gently north-dipping fracture system that cuts across north-northeasterly trending gently southwest-plunging, tight Acadian (early Middle Devonian) folds. This vein system continues at depth into a siliceous skarn zone intruded by altered granite porphyry dykes, which constitute probably a late phase of the Hawkshaw granitoid intrusion to the north.Most of the ore occurs in a northeast-plunging, trough shaped vein structure that formed where the vein system (gently north-dipping) intersects the axial surf ace zone (steeply northwest-dipping) of an Acadian synform. The trough shaped structure resulted from deflection of the fracture zone (containing the vein system) by competent beds.Emplacement of the quartz-stibnite veins was preceded by, and is in part penecontemporaneous with, the formation ofa micaceous-argillaceous alteration halo, which in turn intersects a patchy biotite alteration zone.The hypabyssal intrusions associated with the Lake George deposit probably represent a late phase (early Carboniferousr) of the nearby Hawkshaw intrusive granitoid complex. IntroductionThe Lake George Antimony Mine is situated 40 km southwest of Fredericton and 2.5 kin north of Lake George, New Brunswick (Fig. 1). The mine is owned by Consolidated Durham Mines and Resources Ltd.Shaw (1940) described the early history and development of the mine. In subsequent years, available drill cores were relogged by several geologists. Much new information became available when an extensive diamond drilling program (Kidd , 1970) was started by Consolidated Durham Mines and Resources Ltd. in 1970. A study of the geology and economic potential of the deposit was made by Glover (1973). Abbott and Watson (1975) made a study of the ore mineralogy. Available drill cores were relogged and a preliminary study of the fracture system in the mine was made by G.A. Pierce and A.A. Ruitenberg during 1976. Outcrops in the area sur rounding the mine are extremely sparse.Between 1976 and 1979 the present authors made a detailed study of the mine workings, available drill core and regional structure in the vicinity of the mine, with results set forth in this paper. The regional geologic setting of the deposit, the geometry and structural controls of the ore zones, and the mineral zonation and rock alteration are emphasized."

Jan 1, 1980

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By J. E. Dutrizac

A pyritic Zn-Pb-Cu ore waspercolation leached with acidified ferric sulphate solutions; zinc and copper were leached, lead was oxidized, but not dissolved, and pyrtte was essentially unattacked. High zinc extractions were achieved after a few months leaching, and substantial zinc solution concentrations could be produced by recycle of the oxidized solution. The leaching rate was generally controlled by the transport of the ferric sulphate oxidant. Zinc extractions increased with increasingferric ion concentration or flow rate, but were essentially independent of the concentrations of sulphuric acid, ferrous sulphate, cupric sulphate or chloride ion. The leaching rates were insensitive to the height of the ore column once a minimum height had been exceeded (0.8-1.0 m). Elemental sulphur was the principal sulphidic reaction product, but variations in the ratio of sulphur to sulphate produced anomalous temperature effects.

Jan 1, 1979

By Bian Xue, Wu Wenyuan

In order to recycle the iron and rare earth from the Baotou tailings, a roasting method was developed involving the addition of C, Ca(OH)2, and NaOH, designed to both decompose the rare earth minerals and convert haematite into magnetite and allow its recovery. The effect of various parameters such as roasting temperature, roasting time, C addition, Ca(OH)2 addition, and NaOH addition on the reduction ratio of haematite (iron sesquioxide) and decomposition ratio of rare earth were investigated. The results showed that the reduction ratio of haematite and the decomposition ratio of rare earth could be as high as 85% and 95% respectively when the roasting temperature was 650°C, roasting time was 60 min, Ca(OH)2 addition was 4%, NaOH addition was 3%, and C addition was 1.5%.

Jan 1, 2014

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004