Search Documents

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

"Batch flotation testwork demonstrated that a low-grade chromite ore from Bird River, Manitoba, was best floated at pH 2 using Armac C (coco amine acetate) collector and sulphuric acid as pH modifier. A grind of 100% minus 150 um was necessary for liberation, and flotation selectivity was greatly enhanced by prior desliming. A concentrate analyzing 24.2% Cr203 with a recovery of 90.2% was obtained, after three cleaning stages, from ore grading 6.05% Cr203. Total rougher collector concentration was 500 g/t and cleaner collector concentration 380 g/t. Similar grade and recovery were obtained during the pitot-plant evalualion, when a concentrate analy zing 22.3% Cr203 with a recovery of 93% (based on deslimed feed) was obtained for a total collector addition of 630 g/t.Selective flotation in a region of positive surf ace charge implies anionic activation, and a possible flotation mechanism is suggested.IntroductionIn an earlier study(1) of the beneficiation of chromite ore from Bird River, Manitoba, several methods of beneficiation were explored. These included ore sorting, heavy-media separation, and gravity concentration with flotation using Armac C (coco amine acetate) collector at pH 2, and sulphuric acid as pH modifier. Because flotation was not fully evaluated, a laboratory study was undertaken to determine the optimum parameters of chromite flotation. Optimization of parameters was established first on a laboratory scale followed by confirmation a t the pilot -plant level. Flotation of chromite using Armac C and sulphuric acid as a pH modifier has been reported as being selective for low-grade chromite ores(2)."

Jan 1, 1990

By Yuki Soma, Tsutomu Ogawa, Jae Hyung Hong, Toshihiro Nagato

The Saganoseki flash furnace was built in 1973. The steel frames of the flash furnace were designed to absorb the expansion of refractories and contain expansion-absorbing materials between their frames and the skin plate. Expansion and deformation resulted in the furnace settler because of the repeated increase and decrease in temperature from more than 30 maintenance shutdowns. Preliminary investigations were conducted to confirm the condition of the settler, and it was found that partial cracks accompanied the expansion in the lower layer of the refractories. As a result, the risk of molten-matte leakage increased. Based on the above investigation, it was decided that the entire settler should be replaced by introducing a spring-displacement structure that was capable of maintaining the furnace integrity over an extended period. The difficult redesign and rebuilding of the Saganoseki flash furnace was accomplished successfully and safely in 76 days from September to December 2017, as planned. Because of various redesigns, the furnace was changed to a flash-smelting furnace that can withstand higher thermal loads based on recent trends of copper concentrate with increased sulfur and reduced copper. The new furnace is operating smoothly at present. INTRODUCTION The flash-smelting furnace of Pan Pacific Copper Co., Ltd. Saganoseki Smelting & Refinary commenced operation in 1973, with an original designed feeding rate of 71 t/h. As a result of facility remodeling and operational improvements, shown in Figure 1, the feeding rate was increased to 215 t/h in recent years. After more than 40 years of operation, the original settler in the melt holding section of the flash furnace underwent significant expansion and deformation.

Jan 1, 2019

By N. M. Steven, J. M. Moore, J. L. Kuyper

Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, Iargelyensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegrnatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphic order of host rock): (1) thin (5 cm to 2 meter) quartz+plagioclase+diopside ± scapolite calc-silicate granofels with fmely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the calc-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); (2) gamet+pyroxene± vesuvianite+scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unrnineralized leucogranites; (3) metaturbidite-hosted scheelite- (and possibly wolframite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; (4) scheelite-bearing vesuvianite+quartz+garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt5 WO3 and 8 wt% CaF2•

Jan 1, 1994

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By É. Poulin, J. Bouchard, E. M. Pérez-García

Process control and optimization have always been crucial aspects in the mineral processing industry, and expectations constantly increase to cope with more stringent security, quality, efficiency, and environmental performances. The main challenges to reduce variability of key process variables, and steer profits to higher values while maintaining sustainability indexes within acceptable ranges come from nonlinear responses and circulating loads. The most commonly implemented control strategies rely on simple PID controllers for practical implementation and maintenance considerations. If arguably good performances are accomplished when these are adequately set up, there is also room for further gains by using more advanced methods such as model-based techniques. There is thus a need for more realistic process and equipment models. Based on advances of the past few decades, this paper introduces an autogenous/semi-autogenous mill (AG/SAG) model to be included in a modular comminution circuit simulation toolbox comprising ball/rod mills, material handling, and classification devices. The proposed mill model incorporates a modified version of the classic comminution equation that makes grinding rates proportional to the energy input. It requires the determination of a selection function (fragmentation rates) and a breaking function (fragments distribution). The former is modelled with an S-shaped curve characteristic of AG/SAG processes and the latter is a size-relative distribution of the produced fragments. The power draw is predicted employing the empirical equation of Austin. The paper also develops a case study to illustrate how the proposed simulation framework can capture the behaviour of an actual plant. Model calibration consists in an optimization problem that search the global minimum of the difference between predicted and measured/estimated size distributions, power draw, solid fractions, etc. Results demonstrate that the mill simulator can mimic an actual process in its operation conditions. INTRODUCTION Comminution is a key stage in the mineral processing industry, obviously because the phases of interest must be liberated to be able to recover them. In general terms, the global performance of a plant depends largely on the efficiency of the grinding circuit and on the material properties such as its grindability, density, and mineral grades. The subject has vastly been studied since as early as the 19th century, when Rittinger (1867) and Kick (1883) developed some of the first empirical models to relate grinding and energy input. The great interest in the subject comes from the fact that this operation is costly and, probably most concerning, highly inefficient. Buckingham et al. (2011) estimated that ore comminution can represent up to 60% of the overall plant power draw. Moreover, only a modest fraction of the power draw effectively translates into rock fragmentation. For grinding, estimates range between 1% and 25%, depending on the reference used, while the rest is mainly lost as heath (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002; Bouchard et al., 2017).

Jan 1, 2019

By J. Oliver, B. Wilson, 10

"Red Dog is one of the world’s largest zinc producing mines and a significant producer of lead and silver. While some of the operational challenges relate to the mine’s location in a remote part of Alaska, there are also challenges in the mineral separation process. Recent processing upgrades have included the installation of two M5000 IsaMills to improve the zinc regrind circuit and of one Jameson Cell to improve the pre-flotation circuit. Relatively fine grinding is required to achieve efficient mineral separation at Red Dog, but while fine grinding aids in the production of high grade concentrates, it also creates challenges in the efficient recovery of fine minerals. Over half of the lead lost to the lead circuit tailings, as well as almost half of the zinc lost to the final tailings, is in the finer size fractions (<10 µm). The high pulp density experienced in the pre-flotation and lead rougher circuits also causes significant entrainment loss of lead and zinc to the pre-flotation concentrate and of zinc to the lead concentrate. To help improve fine mineral recovery, Red Dog has recently plant tested and installed magnetic conditioning technology in the flotation circuits. The equipment aggregates fine paramagnetic sulphides and selectively increases their flotation recovery. This paper outlines the testing and positive results at Red Dog.INTRODUCTIONRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine. Red Dog Ore and Mineralogy The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The main minerals present in order of abundance are: quartz, sphalerite, pyrite, barite and galena. Production began in 1989 with mining of the Main deposit. Between 1989 and 2012, approximately 55.6 million tonnes of ore with an average grade of 20.5% Zn, 5.6% Pb, and 97 g/t Ag was mined from the Main deposit. Subsequent to the development of the Main pit reserve, two additional open pit deposits were discovered: Aqqaluk and Qanaiyaq. The first blast in Aqqaluk occurred on June 4, 2010. As of December 31, 2014, the Aqqaluk deposit reserve is an estimated 45.7 million tonnes of ore with an average grade of 15.1% Zn, 3.9% Pb and 71 g/t Ag."

Jan 1, 2016

By Xuanxue Mo, Kaihui Yang

"The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Early Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry. The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affInities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental microplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820/0 Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 glt) and recoverable amounts of Au, n, Gd, Ga, Ge, In. A massive sulfide zone, in which lenticular and stratiform orebodies are localized in a sulfide-<:arbonate-silica shale unit or sulfidic tuffIte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulfide zone developed in a subvolcanic intrusion or volcanic sequence. The sulfIde mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite - chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerals occur rarely in the massive ores. The massive ores are generally fme-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and displacement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two distinctive alteration zones have been identifIed: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, tremolite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive model of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016

By Javier Ramirez

"Recent R&D pilot plant testing was done to validate a full industrial scale system for recovering residual magnetite from the tails of an iron ore concentration plant. The recovery system is based on an autogenous heavy media separator treating a tailings slurry at 0.45% solids by weight. A 3,100 m3/h capacity concentrator was installed based on the testing findings. Excellent metallurgical results have been observed in two years of continuous operation. This experience is the basis for the proposal of a novel process consisting of the preconcentration of base metals ores; the idea being to obtain a heavy bulk concentrate of the polymetallic minerals and discarding in one step the light gangue mineral components. The bulk concentrate then proceeds to conventional froth flotation. The reduced volumetric flow of the bulk concentrate allows a reduction in the size of the subsequent flotation circuit. A prerequisite for the heavy media separation is a fine size grinding of the ore and a correspondingly high degree of liberation of the mineral species to be recovered. A process scheme is also presented in which the gravity concentrator works in conjunction with a companion tailings thickener for process water recovery. The underflow from this thickener, having paste consistency, can be sent to a tailings dam or mixed with Portland cement for mine backfill. The process water in the system is managed at an estimated recovery in excess of 98%. Additional R&D work using this novel approach is being considered by a large iron ore concentrator for removal of liberated silica from the final concentrate; and for upgrading 3.5 million tons of a marginal hematite reserve owned by the mining company.INTRODUCTIONGravity preconcentration (static and dynamic) of sulphides prior to froth flotation has been and is being practiced at various concentrator plants (Asarco´s Young Mill: heavy media cone; Mount Isa: DSM cyclone; Afton Mines: Denver jigs; Tsumeb Mine: Reichert cone) (Burt, 1984). The idea behind installing preconcentration equipment is to reduce the volume of feed processed on flotation, thus requiring smaller flotation plants although other advantages may be of importance, such as obtaining richer concentrates due to higher grade feed, better process water and energy management, and reduced flotation reagent consumption.The SedconTM solid/liquid separator is a versatile process unit patented in Mexico (MX/u/2007/000305). As a gravity device, it may be classified as an autogenous heavy media dynamic concentrator. Figure 1 depicts the Sedcon (Sedimentador de conos) separator. The four main components are as follows: the feedwell for efficient mixing of the pulp with dilution water and flocculant (and coagulant for water clarification); the inner cones (passive elements for solid/liquid separation); the discharge underflow cone; and the scraper mechanism. The standard discharge cone is a 60° inclined cone for general applications. For paste tailings thickening applications, a deep cone with a 69° inclined cone is used."

Jan 1, 2016

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By P. Garritsen, J .. A. Blanco, M. C. Bell

"By 1994, Inco Limited will lower sulphur dioxide emissions from the Copper Cliffsmelter by 60% to 265 000 tonnes/year, primarily through implementing two key process changes. First, new milling technology will permit economic rejection of additonal pyrrhotite prior to smelting. Second, a bulk coppernickel concentrate will be oxygen flash-smelted, thereby eliminating the existing multi-hearth roasters and reverberatory furnaces . All copper will be recovered in the matte separation plant as a nickeliferous chalcocite, and will be oxygen flash-smelted for blister production. This paper outlines the development of the project and describes the process, including the flash furnaces, new sulphuric acid plant and additional oxygen plant.IntroductionInco &apos;s SO2 Abatement Program will lower sulphur dioxide emissions at Sudbury from the current levels of 685 000 tonnes per year to 265 000 tonnes per year by 1994 as required by Ontario&apos; s countdown on acid rain regulations.It is the high tonnage of sulphur mined that creates the magnitude of the SO2 emission problem at Sudbury. At a production rate of 240 million pounds of nickel per year, Inco mines 12 million tonnes of ore. At 10% sulphur it mines 1.2 million tonnes per year of sulphur. If Inco did not fix any of this sulphur it would be emitting 2.4 million tonnes per year of sulphur dioxide-about as much as all other Canadian emissions. Today, however, Inco is already fixing 70% of the SO2 in ore, in several ways : mostly as sulphur in pyrrhotite rejected to tailings in the milling operations; as acid from the roasting of pyrrhotite and some nickel concentrate at the Iron Ore Recovery Plant (lORP) and some as liquid S02 from the copper flash smelting furnace. By fixing 70% of the sulphur the current allowable SO2 emission levels of 685 000 tonnes per year is met. Total sulphuric acid production is currently 450 000 tonnes per year and in fact, the 10RP operation is being continued only to maintain established acid markets.Historically emissions have been reduced from the 2 000 000 tonne per year level to the current level of 685 000 tonnes per year by rejecting pyrrhotite from the smelter feed, and 70% of the SO2 containment problem at Sudbury has already been addressed.While Inco&apos;s profits are large at current nickel prices, most people have forgotten that back in 1982 Inco was losing a million dollars a day. Inco did make a dramatic response to this economic stimulus. The Ontario Division increased productivity by 65% and lowered costs to become the lowest cost nickel producer."

Jan 1, 1990

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

By C. Sist, J. Shannon, J. Fossenier, J. F. Adams

With the cleanest and easiest to treat copper concentrates dwindling and becoming harder to find, electrorefineries must deal with the reality of higher impurity anodes. There are well-known strategies for managing nickel, bismuth, antimony, etc. using bleeds (Ni, Bi, Sb, As) or arsenic control (Bi, Sb) or hydrometallurgical add-on circuits (IX, MRT, SX for As, Bi, Sb). However, for integrated copper producers and those producing other base metals it is often worth considering a more holistic, global approach. This paper will discuss both the well-known strategies as well as some global strategies and the role that hydrometallurgy can play in them. Examples will include atmospheric and pressure leaching, selective precipitation and impurity recycling or fixation. INTRODUCTION In the electrorefining of copper, impure copper anodes are electrically corroded, and pure copper is deposited on cathodes by passing DC current through an acidic copper sulphate solution. The anode copper impurities either settle to the cell bottom as insoluble components (anode slimes) or remain in solution with minimal deposition at the cathodes when correct operating parameters are maintained. Consideration of impurities is important in all copper electrorefineries. A typical impure anode contains 98.5–99.5% copper (Schlesinger et al., 2011). Table 1 shows the range of impurities reported for all copper anodes in the 2007 survey of operating refineries (Moats et al., 2007). Also shown is an approximate “limit” of anode compositions within which the majority of refineries operate without additional impurity removal capacity (beyond conventional liberator/bleed circuits). The column is somewhat subjective and meant to be an approximation only since there are many factors that influence impurity deportments and refinery impurity tolerances. More recent world survey data from 2013 show the averages for all impurities trending upward from 2003 to 2013 (Moats et al., 2013). With a competitive market for good concentrate and more copper recycling from electronics (which contain high levels of impurities such as nickel, lead and antimony), this trend is expected to continue through the coming years. The traditional primary method of impurity control is refinery bleed through liberator cells which are employed in the vast majority of refineries (Moats et al., 2013). These are used to control copper (primary liberators), nickel, arsenic, antimony and bismuth (secondary and tertiary liberators). Other methods of impurity control include arsenic addition (upstream in the smelter deporting to anode or directly to electrolyte) to control antimony and bismuth (Kamath et al., 2003), ion exchange or molecular recognition technology (Hur et al., 2005; Navarro et al., 2012) for antimony and bismuth. Many refineries also operate nickel evaporators to remove nickel sulphate before recycling back acid. Some use, or are contemplating using, acid purification units to recycle acid and arsenic without nickel and making nickel carbonate (Kamath et al., 2003; Sheedy et al., 2006).

Jan 1, 2019

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October, 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are cap1ble of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadi11gs. Final capital expenditures for the project will approach $10 million and annual operating costs are estimated at $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described."

Jan 1, 1980

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Maurice Hall Haycock

ONE result of the higher price of gold has been the exploitation of many low-grade deposits, the successful treatment of which depends upon obtaining high recovery of the contained gold. Modern methods have made it possible to recover gold from many ores formerly regarded as impossible to treat economically, but in order to apply these methods efficiently it has become desirable, and indeed in many cases indispensable, to gain precise information concerning their mineralogical and physical character. The most successful means of doing this is the use of the reflecting microscope. Reflecting microscopes had long been employed by metallurgists for studying polished surfaces of iron and steel when, thirty years ago, Dr. W. Campbell, of Columbia University, advanced the idea of using similar methods for studying opaque minerals (1). The immediate result was the completion of two microscopic studies, the first on Cobalt silver ores (2) and the second on Sudbury nickel ores (3). The idea was surprisingly slow in being adopted, and not until 1911 did it begin to spread through the universities of this continent. From then on, ore microscopy, or &apos;mineragraphy&apos;, made rapid progress, and, during the next fifteen years, research in universities of North America and Europe led to the development of somewhat specialized apparatus and technique. This phase of development, which resulted largely in contributions of a descriptive nature, furnished a mass of data from which the possibility of economic applications was soon recognized. Ore microscopy became an aid to the mining geologist in solving many problems of ore deposition. This soon led to its application in the study of ores and mill products in connection with their treatment. Its usefulness in this latter field has been very marked and has led to its widespread adoption by the mining industry.

Jan 1, 1937