Search Documents

By D. Nikols, G. Caraghiaur, P. C. Roxburgh

"IntroductionThe Highvale Mine is located 70 km west of Edmonton , Alberta on the south side of Lake Wabamun. It has been developed by TransAlta Utilities Corporation as a captive mine to supply fuel to two genera ting power plant s. The mine is owned by TransAlta and operated under contract by Manalta Coal. Within the mine permit area, TransAlta own s the right to mine 80% of the recoverable surface mineable coal.The planning process starts with the annually produced 25-year energy forecast which is provided by the Electric Utility Planning Council (EUPC). A 1983 forecast predicts an average annual increase in energy requirements of 4% over the next 25 years. Put another way, the requirement will double before the end of the century. A lar ge part of the base load generation of the Province of Alberta is provided by th e plants fueled from Highvale Mine. The Highvale Mine is therefore expected to maintain a high output over a long period of time.Mine PlanningMine planning is an ongoing, interative process that draws from many sources. All levels of planning draw from the same sources but du e to the different processes and objectives of each planning class, the degree of influence may differ. The planner becomes then a coordinator bringing together data and excerpts from several disciplines in groups. Generally, there are four classes of mining plan s; these are all used at the Highvale Mine (Table I)."

Jan 1, 1986

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By W. G. Schultz

"Sylvite's potash mine, which produces 8,000 tons of ore per day, probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hour production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tons per hour. The ore is produced by two Marietta miners weighing 258 tons, the largest and heaviest pieces of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000-ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground. Because Sylvite's mine is a new operation with equipment of a new design, the full potential of the operation has not yet been realized. The ultimate capability is clearly evident from the success Sylvite has had over the past year as the average mining capability has risen from 100 tons per hour to 600 tons per hour."

Jan 1, 1973

By Fidelis T. Suorineni

HydraboltTM is a Swellex-type dowel support element developed and manufactured by New Concept Mining in South Africa. Like Swellex, the HydraboltTM is a folded tube which can be inserted into a larger diameter hole without pushing. It is then activated by injection of high pressure water which inflates the folded tube to intimate contact with the walls of the borehole at a set pressure, normally 25 MPa. Unlike Swellex however, the set water pressure at the end of the inflation is maintained throughout the life of the dowel. An integral non-return valve makes this possible. The HydraboltTM is being investigated as a possible stress change measuring cell. This paper presents the results of closed form solutions, numerical modeling and laboratory test to date. Preliminary results indicate that the HydraboltTM can be used as a stress change monitoring cell in addition to its conventional role as a rock mass reinforcing element. If successful, the HydraboltTM will supplement microseismic monitoring systems in rockburst-prone ground conditions where they will give quantitative stress change data for both mine design model calibrations and means for proactive safety measures.

Oct 1, 2010

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By Tony B. Szwilski

"The efficiency of operation and life of an advancing longwall coalface depends, to a great extent. on the face-end roof strata conditions and the stability of the gateroads. The factors that influence the rate of closure of gateroads are examined, in particular the gateside pack and the coal rib (crush) pillars. The performance of mechanized packing systems is briefly discussed. Gateroad deformation surveys were carried out at two coal mines to determine the influence of the rib pillar width on gateroad stability; also, the influence of the gateside pack on the immediate roof and floor strata is analyzed based on strata bed displacement measurements from instruments installed in the gateroad and pack-hole of a longwall advancing face operating in a thick seam (7.55 m). Concluding, an evaluation of the fac e-end systems examined is given and recommendations made f or the most suitable rib pillar width. face-end geometry and roof strata reinforcement.IntroductionKevword s: Coal mining, Pillars, Rib pillars, Ground control, Longwall mining, Gateroads , Packing systems, Roof control. The face-end region of a longwall advancing face is the center of mining activity, being the turn-around point for the coal cutting machine. and the place of gateroad formation and movement of special face-end supports. The design of face-end layouts can be aided by knowledge of strata control parameters, such as the effective loading of the immediate roof strata , convergence of the roof and floor, magnitude and distribution of fractures in the roof strata around the face-end , optimum placement of supports, coal seam thickness and strength characteristics, geometry of layout and interaction from neighbouring workings. Generally, the gateroad is formed by one of three face-end methods: (a) advanced headings, (b) in-line system (gateroad formed at the face) or (c) conventional ripping with or without stable elimination (also halfheading). The quality of gateroad is influenced principally by the face-end system employed, standard of gateside pack and width of pillar. A good standard of gateroad is generally achieved by employing the half-heading face-end system, the gateside pack and coal rib pillar having comparative support/ yield (stiffness factor) characteristics. However, the halfheading is often not favoured due to face operation restrictions."

Jan 1, 1981

By J. F. K. Brown

MR. T. L. McCALL: Planning ahead in coal-mining is essential, but the question may be raised, just how far ahead can we plan. You can overdo it: chat is, you can get in a rut. Never let planning get a hold on you to chat extent. You must be prepared to deal intelligently with any new conditions that arise, and to apply new discoveries. It may become necessary to abandon ? .your plan, make the best you can of the ground you have developed, and start again, with a new plan. So far as the submarine workings of the Dominion Steel and Coal Company are concerned, we cannot know definitely what lies ahead of us under the sea: we must ?base our tentative plans on assumptions, and, as we meet changing conditions, we must change our plans. In the case of inland mines it is possible to bore in advance, and consequently it is generally possible to set out your plans in advance, block out a section of the mine, and develop to obtain a uniform product for a whole year, or perhaps even longer. MR. J. B. MORROW: While planning in coal mining, we must bear in mind chat the consumer also is planning ahead. Some people will tell you that, in ten years time, the demand is going to be all for pulverized co al; others believe that the field for such fuel is limited. Needless to state, planning for a pulverized-coal market is quite a different matter to planning for a general grade, ore stoker, market. In planning, therefore, our endeavour must be to keep a jump ahead of the work being undertaken by the anthracite producers. This year, they are spending about two million dollars-money contributed, not by the Government, but by the industry itself-in the study and promotion of new and improved ways of burning anthracite. For example, they are perfecting small hot-water heaters, and one they have brought out weighs only about ten pounds. I feel that research of this type must be regarded as an essential part of planning in coal mining. We, in the soft-coal industry, are also planning types of more efficient burning equipment and doing other investigational work.

Jan 1, 1937

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By Stanley G. Butcher

Predictions of coal cleaning plant performance from the washability data are traditionally used at the conceptual design stage of a coal preparation plant to confirm process selection. The development of computer programs which simulate the operation of a plant facilitates the optimization of product yield and quality, and ultimately proceeds. It is shown that the optimum is sensitive to changes in mine operations and market price structure. A computerized review of operations is thus recommended as an on-going activity .

Jan 1, 1979

By S. Asano

Hydrometallurgical processes for treating copper sulfide concentrates have attracted considerable attention over thirty years and many processes have been developed. However there have been still problems in those processes because of difficulties of iron removal and high purity copper production with low operating cost. Although SX-EW is highly cost effective method, it is difficult to process the chalcopyrite. Sumitomo Metal Mining Co., Ltd. (SMM) conducted a review of hydrometallurgical copper concentrate processing and has successfully developed a novel process for the hydrometallurgical production of copper from copper concentrate. In this process, copper sulfide is leached by chlorine gas under atmospheric pressure. Most of hydro metallurgical processes can leach only some of chalcopyrite under atmospheric pressure then they need high pressure leaching facility like autoclave. In this process, copper in chalcopyrite can be leached completely by controlling oxidation reduction potential and chloride ion concentration. Cu(I) ion in leached liquor is separated from Fe(I!) ion by SX using TBP then pure copper powder is produced by electrowinning. Results in batch and continuous testworks and pilot plant tests at Niihama Research Laboratories are presented in this paper. Cu2007

Jan 1, 2007

By S. F. Dudka, T. Dang, M. L. Wong

Abstract - The Nui Phao W-F-Cu-Au-Bi deposit is located in one of the poorest regions of northern Vietnam. The deposit is currently undergoing a pre-feasibility study by Tiberon Minerals Ltd., with a view to developing what would be the largest WO3 mine and one of the five largest fluorite mines in the world. The project is being planned in close compliance with World Bank and national guidelines for environmental and social protection. Development of the mine is anticipated to bring the following benefits: remediation of serious pre-existing environmental conditions (natural and anthropogenic heavy metal contamination and acid rock drainage); provision of employment and training, and thereby wealth, to local communities; significant tax and royalty payments to government, which will be reinvested as social spending; and development of municipal and industrial infrastructure to build sustainable post-mining communities. The role of governments at all levels is critical in guiding and facilitating this process. This paper was written prior to development of the mine, and relays the intentions of the developers. Future studies will be needed to evaluate the degree of attainment of sustainable development objectives, both during mine operation and after closure.

Jan 1, 2003

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By C. Díaz, A. D. Dalvi, C. E. O'Neill

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur- deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters.

Jan 1, 1994

By Paul G. Dunn

Safe rapid drift development results principally in reducing exposure of underground workers to the working face. This reduction in exposure is not achieved until either the rock walls have been suitably scaled or sufficient support has been put in place. Rapid drifting enables quicker access to orebodies (increasing returns), higher production rates and a resultant lower cost of mining. The Mining Innovation, Rehabilitation And Applied Research Corporation (MIRARCO) has been developing technology and a methodology for safe rapid drift development within the underground metalliferous mining industry. In terms of rock scaling for underground metal mines, there is still considerable use of manual and mechanical impact rock scaling techniques. Two main issues result from this approach. The first is that in highly stressed or highly fractured ground, a decision has to be made as to when sufficient scaling has taken place. This is not always easy to do and hence operator judgment is a crucial element in this approach. During a baseline study of current rock scaling practices, a wide range of scaling practices were observed within five different underground mining operations; this demonstrates the difficulty inherent in the rock scaling quality decision making process. The second issue is related to the exposure of workers to freshly created rock surfaces. In manual scaling techniques this is unavoidable and despite the best scaling practices, accidents still occur. In an attempt to provide an alternative scaling technology, MIRARCO has been investigating highpressure water jet scaling for removing loose rock as part of the drift advance process. This technology not only provides a means by which scaling practices can be engineered (remove the loose material you want to in a given rock mass condition), it is also quicker and easily automated. Automating the scaling process removes workers from exposure to freshly created rock surfaces and also enhances the application of spray-on liners through improved adhesion of these support types to the rock surface. This paper describes the water jet scaling technology research and methodology for safe rapid drifting within the underground metaliferous mining industry and highlights the key issues and major drivers behind their continued development at MIRARCO.

May 1, 2004

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004