Search Documents

By Y. M. Shneerson, E. E. Zhmarin, E. M. Vigdorchik

One of the Gipronickel Institute activities is research and development of customized leaching technologies. The work is performed in several steps. Leaching kinetics are studied on a lab-scale according to a special procedure. Experimental data are processed using mathematical models of batch and continuous processes. Reliability of kinetic data and preliminary calculations is verified experimentally in laboratory reactors of various capacities. If necessary, certain parameters of the mathematical model are adjusted after pilot plant tests in continuous mode ( 4-reactor train, each with 25 L capacity). The specified kinetic characteristics along with the mathematical model are used for further development of industrial leaching technology.

Jan 1, 2005

By Ronald C. Schimmel

In 2006, the Corus IJmuiden pellet plant produced approximately 4.6 mln tonnes of pellets. Corus IJmuiden is about to increase its pig iron production to 6.4 mln tonne HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50% high basicity sinter and 50% acid pellets, both produced in-house. To enable an increased iron production, the capacity of the pellet plant needs to be raised to 5.0 mln tonne per annum. The capacity is increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

May 1, 2007

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Anthony Finch

Many mines combine open pit with underground mining, and on many occasions the underground mine is an extension of the open-pit. In these circumstances the decision about where the open-pit stops and the underground starts is crucial and driven by many factors. This paper looks at some of the ways that this cut-over can be calculated and specifically examines the calculation of it using modern mine optimization software. The paper provides a case study which will review various outcomes using these techniques, and demonstrates the influence of various factors on the optimal transition cut-over point. Biographies Mr Finch is a Divisional Manager and a Principal consultant at Snowden Mining Industry Consultants in Vancouver, Canada. At Snowden Mr Finch leads a team of engineers that perform mining engineering studies for projects around the world. Prior to joining Snowden Mr Finch was the Mining Manager at Barrick?s Henty mine in Tasmania Australia. Prior to that Mr Finch has held a variety of roles in both consulting and operations working for various organisations at various levels in the Asia Pacific region. Mr Finch gained a bachelor?s degree in Mining Engineering from the University of Queensland in 1986, and a bachelor?s degree in Economics from the University of Queensland in 1993. His expertise is in mine planning, mine optimisation and mine management. Dr Elkington is a Consultant at Snowden Mining Industry Consultants in Perth, Australia. He is responsible for the design and implementation of Snowden?s proprietary optimization software products. Prior to joining Snowden Dr Elkington completed his PhD in Mine Optimisation at The University of Western Australia, and bachelor?s degrees in Engineering (Hons) and Commerce from The University of Western Australia. He specialises in optimization and trade-off studies, and has consulted on projects across all major commodities and regions.

May 1, 2011

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By Peter Lighthall

What is an engineering firm?s role? ? The ideal situation is a life of mine service alliance with the owner ? Engineering firms are long term custodians of information ? Maintain consistency with established closure objectives, adjust closure plans to meet changing situations and technologies ? Develop range of solutions and present owners with risk profile The mine closure planning process ?new mines ? For metal mining, geochemistry is the issue ? The planning process: ?Sampling ?Waste characterization ?ARD prediction ?ARD control strategies ?Life of mine waste management planning ?Assessment of residual impacts ?Development of strategies for dealing with residual impacts ?Estimate closure costs ?One time decommissioning and reclamation costs ?Ongoing treatment/maintenance costs

May 1, 2006

By M. J. Bennett

"The Quemont mill is primarily a differential flotation plant in which copper, zinc ·and pyrite concentrates are recovered. Native gold and silver are associated in the form of very small particles with all the minerals contained in the ore: chalcopyrite, sphalerite, pyrite, pyrrhotite and even with the gangue rock.The proportion of the precious metals associated with chalcopyrite is such that the best recoveries we can obtain in our copper flotation concentrate are about 68 percent of the gold and 51 percent of the silver in the ore. In order to improve the total recoveries of precious metals it is necessary for us to float a pyrite concentrate and treat it by cyanidation for the extraction of whatever gold and silver we can obtain in this manner. In spite of the fact that we regrind this concentrate to 75 percent minus 325 mesh, it is difficult to extract much more than half of the gold and silver present in the pyrite concentrate by cyanidation, due to the extremely fine association of the precious metals with the pyrite.In 1963 we produced 86, 853 ounces of gold by flotation alone, and 14, 581 ounces by cyanidation. These amounts are equivalent to 67. 74 percent and 11. 37 percent respectively of the total gold in the mill heads. Comparable figures for silver are 325, 598 ounces by flotation and 99, 448 ounces by cyanidation; and 51.37 percent and 15.69 percent respectively.The total annual value of these metals (ie. $4, 000, 000) qualifies Quemont as a precious metal producer of some note. On the other hand, it is evident that by far the greater proportion of our gold and silver production is contained in copper flotation concentrates. When the income from our copper and zinc values is also considered, the much greater importance of flotation compared with cyanidation in our operation may be appreciated. This explains why most of our work on controls has been carried out in our flotation mill, rather than in our cyanide plant. Some of the controls installed there could, of course, be employed in either type of operation."

Jan 1, 1964

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By P. R. A. Andrews

"The sillimanite group minerals, kyanite, sillimanite and andalusite are identified as alumino-silicate minerals with the common chemical composition AIP3.Si02' so that each possesses similar physical properties. Kyanite is the most abundant mineral and mainly occurs in Quebec, Ontario and British Columbia; sillimanite occurs in Ontario and Manitoba; and andalusite in Nova Scotia. The main use for the sillimanite-group minerals is in refractory applications for the production of refractory bricks and shapes. In refractory applications, the main performance criterion is the relative percentage of mullite formed within the material during firing. This phase gives a greater degree of resistance to creep deformation and slag attack, and improves the ability of the refractory to withstand high temperatures under load. The beneficiation of refractory silicate minerals has been the subject of many investigations at CANMET, and the former Mines Branch. Eighteen kyanite, two sillimanite, and three andalusite evaluation studies were conducted between 1933 and 1987. A review of some of the more important studies is presented, which includes information concerning mineralogy, beneficiation methods and flotation data."

Jan 1, 1995

By Christina Graf

A synthesis of colloidal gold shell particles with a silica core is described. Small gold nanoclusters were attached to the functionalized surface of colloidal silica particles. Reductive growth and coalescence of these clusters lead to the formation of a closed gold layer. By variation of the thickness of this gold layer and the radius of the shell it is possible to adjust the plasmon resonance of the gold shell particles over the whole visible and infrared region of the spectrum. The optical properties of the particles made are in good agreement with theoretical calculations for coreshell particles. Due to their low polydispersity these gold shell particles form in solution large crystals with submicron lattice constants. It is also possible to produce hollow gold shells by dissolution of the silica core. A new method to coat the silica core gold shell particles with an additional outer silica shell is also presented. This allows due to a reduction in the Van-der-Waals forces to make more permanent dried crystals and facilitates functionalization of the particles for use in various photonic applications.

Oct 1, 2003

By T. Saksala

In this paper, the embedded discontinuity approach is applied to finite element modeling of rock fracture. A rate-dependent constitutive model based on the embedded displacement discontinuity theory is developed to describe the mode I, mode II and mixed mode fracture of rock in tension and compression. The bulk material is described as linear elastic until reaching the elastic limit. Beyond this limit, a ratedependent exponential softening law governs the evolution of the embedded displacement jump. The present approach incorporates the rock heterogeneity by random description of the mineral texture of rock. Moreover, the inherent initial microcrack populations of natural rocks are accounted for as randomly oriented embedded discontinuities. Numerical examples demonstrate the model behavior in uniaxial compression and tension. The effect of loading rate and confining pressure is tested as well in 2D numerical simulations. These simulations show that the model captures the main features of rock in confined compression and uniaxial tension. The developed method has the computational efficiency of continuum plasticity models. However, it has an important advantage of accounting for the orientation of introduced microcracks.

Jan 1, 2015

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012