Search Documents

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By Bern Klein, A. Tugba Cebeci, Libin Tong

"Sensor based sorting faces two main challenges related to limited capacity/throughput and the ability of sensors to accurately discriminate based on estimated grades. This paper is aimed at improving sensor discrimination. Sensors have the ability to measure more than a single response. X-ray fluorescence (XRF) can detect and provide concentration information about a range of elements. Similarly, electromagnetic sensors (EMs) can generate magnetic susceptibility and conductivity responses over a range of frequency levels. The sensors thereby provide a response signature rather than a simply a single response that is a proxy for a metal grade. Furthermore, integrating sensor responses can improve the discrimination of metal bearing rock from waste. A study was conducted on a gold ore to assess sortability using XRF and EM sensors. A multi-variable regression approach was used to develop models that included a range of responses. Correlations improved significantly when compared to single response correlations. The approach showed that both positive and negative correlations contributed to the improved correlations. Stepwise regression simplified the models and showed that 2nd order interaction effects can be important. The approach also showed that combining different responses can improve discrimination accuracy. An important outcome of the study was that an ore that had been consider not to be sortable was determined to be sortable through the application of an approach that used the sensor responses in a more intelligent manner.INTRODUCTIONMining is aimed at recovering valuable minerals from their host rocks. Many methods are used to recover valuable minerals, and finding efficient and cost-effective ways is the key in research and production. . Ore sorting technology is fitting this definition. It not only discards waste rocks away from the concentrator but also recovers metal bearing ore particles that could be lost to the waste dump. The benefits of ore sorting include increased energy efficiency and reduced water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013)."

Jan 1, 2016

By S. A. Willis

For over 150 years gypsum from Nova Scotia has been shipped via water to the United States east coast. The history of the movement has been one of continual improvements in quarrying, loading, and shipping. At the start, man-size rock quarried by hand auger and black powder was loaded into horse-drawn carts, hauled to the waterfront, and dumped into 100-ton sailing schooners. Last year the Canadian Gypsum Company completed the latest and most modern of these successive installations for the movement of this Nova Scotia product. The new system loads crushed gypsum into 11,600-ton vessels at Hantsport in two hours' time at high tide. At the head of the bay of Fundy are located vast deposits of gypsum. The tidal rise and fall of 45 feet twice a day, with its attendant swift currents, has always presented major navigation and shipping problems. When the tide is low, the Hantsport ship-loading pier is high and dry, with no water within 400 feet. Three hours later a large river has flooded in (running up hill) and large steamers can dock at the wharf. Before high water, the ship has been loaded and -there is a depth of 30 feet or more of water around the wharf. At high water, the ship sails away on the ebbing tide as the river runs in the other direction. Tides are caused by the gravitational attraction of the moon and sun on the ocean. When both celestial bodies are pulling together the 'spring tide' results, which means a 50-foot variation from high to low. This occurs at new and full moon. A week later, when the sun and moon work in opposition, the difference is only 32 feet between high and low water. The bay of Fundy, having a funnel shape (150 miles wide at mouth from Yarmouth to Portland, while the upper estuary at Hantsport is only one mile wide), builds up a tidal influence from 10 feet at the mouth to an average of 45 feet at Hantsport.

Jan 1, 1948

By Franco Oboni

Numerous voices are raising around the world to show how misleading and fuzzy commonly used risk assessments methods are. These criticisms come at a time when public trust in ?proponents of new projects?, operators, private or governmental, seems to have hit a low and the legal system ?targets? public officers. It is common that technical experts and the public strongly disagree in their analysis of risks. Risk definition requires the evaluation of probability and consequences and those words are oftentimes enough to stir great worry to the public. Thus it is nowadays commonly understood that ?reality? is not scientific, but resides in public opinion, hence urging technical people to communicate better, more transparently. Blatant failures on both counts have lead to the emergence of ?new myths? used to justify complacency using ?complexity? and other buzz words as an alibi. This paper (together with its companion presented elsewhere) explores how poor ?common practices? in Risk Assessment contribute to biasing project team, design teams opinions, skew decision-making process and finally misrepresent reality to the public resulting precisely in the raise of public distrust, legal implication witnessed around the world. The discussion first reviews the pitfalls of common approaches (FMEA, Probability Impact Graphs) pinpointing them as possible causes of future legal liabilities. An alarming disconnect also comes from various codes, ISO 31000 itself has this flaw, invoking the term ?acceptable?/?tolerable? without defining it or giving any guidance for its determination. Wide-spectrum public consultation could be developed to define a ?modern? social acceptability criteria helping all the stakeholders making/understanding decisions. Another alarming disconnect comes from the poor definition of consequences of mishaps and their societal ripple effects. This aspect is indeed mostly ignored in codes, leaving ample room to biases and censoring applied to potential losses. In our society no one seems to have anymore the possibility of hiding behind a shroud of ?carefully maintained? misrepresentation. It is time to act and ?write the book? for proper risk assessments avoiding misrepresentations.

May 1, 2013

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By E. Wusaty

"Fording Coal is a wholly owned subsidiary of Canadian Pacific Limited. The company was founded in 1968 to mine metallurgical coalfor export at the Fording River operations in southeast British Columbia.Today, Fording Coal Limited also operates the Whitewood mine under contract to TransAlta Utilities and the Genesee mine under a joint venture arrangement with Edmonton Power. Both these operations are located just west of Edmonton and produce subbituminous low-sulphur coal which is used for power generation. Fording also owns and operates two industrial mineral mines in the United States and is mining overburden under a lo-year contract with Syncrude Canada at Fort McMurray.As of December 1992, Fording Coal Limited owns and operates the Greenhills mine which was closed due to bankruptcy. This papers deals with the innovations and changes which have been made and those which are currently being implemented to make this operation competitive in the world export coal market. IntroductionOn December 4, 1992, following a tendering process, Fording Coal was awarded 80% controlling interest in the Greenhills mine by Trustee Arthur Andersen Inc. Assets acquired included 100010 of the land and coal leases and 80% of the major joint venture assets including all structures. The remaining 20% is owned by Pohang Steel Canada Ltd., a wholly owned subsidiary of Pohang Iron Steel Co. of Korea. The Greenhills mine had been in continuous operation since 1983 and was finally closed due to bankruptcy of its majority owner on October 31, 1992.A permit to operate the Greenhills mine was issued by the British Columbia government on January 29, 1993, and Fording Coal Limited started mining operations in late February 1993.To return the Greenhills mine to profitability significant changes were required in workforce productivity, mining methods and equipment selection. These mine plan changes are designed to make the Greenhills operation competitive in world markets, provide longterm employment for the company's workforce and ensure that a secure supply of coal is available."

Jan 1, 1994

By H. E. (Buzz) Neal

"Abstract - The Labrador Trough contains world-class iron deposits which have been mined since 1954. The direct shipping of Knob Lake ores were mined at Schefferville from 1954 to 1982. Concentrate production began in 1961 in the southwest end of the Trough, with three mines currently producing concentrate and pellets at a rate of 35 Mt per year. West and north of Schefferville, several billion tonnes of taconite have been outlined in fine-grained, cherty magnetite iron formation. Several deposits of highly metamorphosed magnetite-specularite iron formation are located west of Ungava Bay. Numerous studies have shown that this medium- to fine-grained iron formation can be beneficated to 66% to 68% iron. In the area from Wabush Lake to Mont-Wright, a medium- to coarse-grained friable specularite-quartz iron formation is repeated by folding to form several large deposits. In this area, three mining operations are located with reserves and resources in the order of 5 billion tonnes.The iron deposits occur within iron formation in sediments in the extensive Proterozoic geosyncline called the Labrador Trough. Several facies of iron formation within the Sokoman Formation reflect variations in chemical composition and depositional conditions. The correlation between the mineralogy and textures is discussed to illustrate the development of different types of iron ores. This band extends for about 1100 km southeast of Ungava Bay through both Quebec and Labrador. Further south, it turns southwest past the Wabush and Mont-Wright areas to within 300 km of the St. Lawrence River. The iron formation is essentially folded and faulted along most of its length. The degree of metamorphism is variable, ranging from intense in the northern and southern portions to greenschist facies in the central portion.The stratigraphy, structure and mineralogy of the producing mines are described along with the history of discoveries. Geological input is required to achieve the strict specifications of the international iron ore market."

Jan 1, 2000

By C. Sartain

In recent years market pressures have been building on companies to develop the next era of mining projects to follow the previous boom in copper projects of the mid 90's. However the response from the industry has been slow in coming, and somewhat muted. It is clear that there simply have not been the obvious quality projects waiting to be rapidly developed. Many of the known undeveloped copper projects have particular characteristics that have previously prevented their development, including mineralogical complexity in the ore bodies, environmental challenges or particularly difficult geographic locations. This paper describes how the Copper Division of an international mining company, Xstrata plc, is preparing to progressively develop an impressive pipeline of projects, armed with an array of proprietary technologies and with a strong approach towards sustainable development and community engagement. The approach being taken is enabling Xstrata to complement its acquisitive corporate philosophy with a management emphasis on project development and operational optimization and enhancement.

Jan 1, 2007

By M. L. Free

Laboratory scale extraction of metals from heterogeneous materials such as copper ores is often performed using fine material to increase kinetics and reduce sample size requirements and costs. In contrast, commercial extraction is usually accomplished using much larger material sizes than are used in laboratory settings. The large size difference between laboratory testing and commercial application materials makes it difficult to use laboratory test data to accurately predict performance for commercial material. One solution adopted widely in industry is the use of large test columns. Large test columns cost considerably more to set up and run and take much longer periods of time to evaluate than laboratory scale tests with small particles. Consequently, from a cost and data collection efficiency perspective, the development of accurate scale up methods offers significant potential for saving both time and money. This paper provides details for a new approach to correct for scale-up phenomena in heterogeneous material processing.

Jan 1, 2007

By B. T. Lu, J. L. Luo, J. F. Lu

The present paper investigates the chemo-mechanical effect in slurry-erosion corrosion process of carbon steel to understand the synergistic mechanism due to interaction of chemical and mechanical factors. The erosion-corrosion tests were conducted with A1045 steel in slurries comprising tap water and silica sand. Various heat treatments were adopted to achieve different hardness in the test material. The chemo-mechanical effect is evaluated in line with the correlation between the degradation of hardness in the surface layer and anodic current density. During the erosion-corrosion tests, various anodic currents were applied to find the relation between the anodic dissolution rate and erosion rate. The experimental results indicate that the hardness decreased with increasing anodic dissolution. Based on the fact that pure mechanical erosion rate increased with decreasing hardness, this result suggests that the corrosion-induced degradation of mechanical property is a mechanism of corrosion-enhanced erosion. This theoretical prediction is verified by erosion-corrosion experimental results.

Jan 1, 2004

By R. Mohamad, J. Asfahani

Abstract - Radioactive characteristics of pits drilled in the Al-Sharquieh mine while prospecting for recent phosphatic resources have been investigated. The results indicate that phosphatic layers are characterized generally by high radioactive intensities (more than 800 c.p.s). The lithological section in the study area is very complex sedimentologically, and characterized by high faciological variation in all directions. The Schlumberger geo-electrical configuration with fine separation of AB/2 was successfully applied to determine lithological boundaries, and the resistivities of the layers of the lithological section, especially for thin layers. It was shown that the phosphatic layer resistivities increase or decrease as a function of associated material. As a result, two types of phosphatic layers have been geo-electrically distinguished. The first is characterized by high resistivity and relatively low radioactivity, which could be related to the rock phosphatic layers. The second is characterized by low resistivities and high radioactivity, which could be related to the sandy phosphatic layers.

Jan 1, 2000

By W. D. Gould, A. Kapoor

Acid mine drainage (AMD) is characterized by low pH and high concentrations of sulfate and dissolved metals such as iron, manganese, aluminum, zinc, and copper. Chemical treatment of AMD achieves pH neutralization and toxic metal removal but also produces large quantities of bulky sludge that requires long-term storage facilities and monitoring. Chemical treatment of AMD achieves only partial removal of sulfate (SO4) and total dissolved solids. Sulfate reducing bacteria (SRB) have been used for the removal of sulfate from industrial process wastewaters. The biological sulfate reduction process generates sulfide and alkalinity. The sulfide produced in the biological sulfate reduction process is used to precipitate metals present in AMD as their respective sulfides and the alkalinity generated is used to neutralize the AMD. This review article will present an overview of biological sulfate reduction processes using SRB, bioreactor configurations, AMD treatment studies, and full-scale systems in operation for the treatment of acid mine drainage.

Jan 1, 2004

By J. Beddoes

The various microstructural factors that influence the creep resistance of y-titanium aluminides are presented and discussed. Titanium aluminides have potential for a variety of intermediate temperature applications in both gas turbine and reciprocating engines. While it is well established that the 'fully lamellar' titanium aluminide microstructure offers superior creep properties, the particular influence of lamellar morphology, third phase precipitation, and grain boundary structure in controlling both the primary and tertiary creep behaviour is presented. The results are primarily based on tensile creep experiments undertaken using several titanium aluminide intermetallic compositions processed via powder metallurgical techniques, investment casting and Bridgman directional solidification. The results indicate that lamellar structure and precipitate formation have a major impact on primary creep, while microstructural degradation through both lamellar and precipitate coarsening influence on the onset of tertiary creep leading to fracture. The results are used to design a creep resistant microstructure produced by directional solidification and the effectiveness of this designed microstructure is demonstrated through 10,000 hour creep tests.

Jan 1, 2004

By F. Musuka, D. Jenkins, A. Keyes

BHP Olympic Dam operates a Direct-to-Blister copper flash smelting Furnace (DBF) and an Electric Slag Cleaning Furnace (ESCF). Tapping blister copper from these furnaces via tapholes is a routine task carried out by trained personnel. Blister tapping is a high-risk activity with personnel operating in close proximity to molten metal. BHP’s risk management framework has identified taphole integrity as key to managing the potential for loss of molten metal containment and molten metal – water steam explosion, both of which have the potential to cause multiple fatalities. As part of the focus on managing this risk, since 2017, a dedicated Taphole Development Team has been embedded in the operation to run an accelerated improvement program focused on safely and sustainably embedding an improved taphole design with greater integrity. The program of works includes selecting and testing of new materials as well as improving operating discipline by collaborating with tapping personnel to convert their knowledge into codified condition monitoring and operating strategies. Computational fluid dynamics (CFD) is being used to derive critical risk controls, and to develop live-alerts to infer excessive refractory insert wear. To date, improving DBF blister taphole mudgun clay has led to more consistent drilling depths and subsequently reduced oxygen lancing requirements, resulting in improvements in taphole insert service life. On the ESCF, insert performance testing and development of a new taphole condition monitoring strategy, is being used to increase taphole insert tonnages to more sustainable levels. Operations personnel have been closely involved in different phases of the change management, this has led to standardization of tapping practices for both furnaces, and improved ownership of the proposed changes. The paper discusses the maturity in taphole integrity risk management as a result of recent and ongoing developments. It then provides an overview of future taphole developments proposed at Olympic Dam. INTRODUCTION Tapping operations at Olympic Dam and learning from significant events The Direct-to-Blister furnace (DBF) at Olympic Dam was built with a conventional design blister taphole, which was designed for manual oxygen lancing and clay stopper bar plugging tapping operations (Campbell, 2005). Manual tapping is a high-risk activity, where personnel work in close proximity to molten metal, and molten metal personal protective clothing and equipment must be used. Opening tapholes by oxygen lancing is a skilled activity and unintentional damage to the taphole inserts can occur. Since 2008, a Mudgun and Drill unit has been developed and trialled and is now in use on the DBF blister tapholes, to remove personnel from the line of fire when opening and closing tapholes. This has the additional benefit of reducing lancing damage to taphole inserts. A new taphole design labelled the Modular Blister Taphole (MBTH) was developed at Olympic Dam for the Mudgun and Drill operation. The intent of the design was for mudgun clay to fill the entire tapping channel when plugging after a tap. The drill would then drill through this clay plug to open the taphole.

Jan 1, 2019

By Fathi Habashi

This Historical Metallurgy Note is the second part of a three-part series, the first of which appeared in the November- December issue of the Bulletin. Part III will be published in February, 1998. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940-1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of his Institute.

Jan 1, 1998

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019