Search Documents

By Yves C. Lizotte, Malcolm J. Scobie

Blast fragmentation is affected by the physical and mechanical characteristics of the rockmass as determined by geology as well as the explosive energy, the partition of this energy, the actual amount of energy transmitted to the rockmass, the blast geometry and the detonation sequence. This paper reviews studies of the influence of geology on blast fragmentation, particularly structure, i.e. the in situ or inherent fragmentation arising from rock discontinuities. Prior structural studies have mainly been limited to comparing equivalent diameters of the in situ blocks with the size distributions of the blasted material. No criteria exist to integrate structure into blast design. This paper reviews on-going studies of the blasted fragment shape and size observed in different rockmasses aimed at analyzing geological control over blasting. Digital photoanalysis was applied {o measure size and shape distributions, to correlate results with block size distributions and shape parameters of the inherent fragmentation. An integrated and comprehensive fragmentation assessment procedure which accounts for geological control is proposed. The potential of this research is to provide a greater understanding of the true contribution of explosives to fragmentation, the effects of fragment shape on system productivity and the reduction of blast-induced damage.

Jan 1, 1994

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By F. Parada L

Two copper concentrate with medium and high enargite content were leached in a 3 L autoclave reactor under conditions based on the CESL process. Copper, arsenic, sulfur and iron were checked in all the experiments and antimony, zinc and molybdenum were evaluated in selected tests. The 98% of the obtained copper extraction is agree with others authors, but the behavior of arsenic, iron an sulfur have some differences. The solid residue was characterized by chemical analysis, DRX and QEMSCAN®. Finally a comparative analysis with neutral roasting as an option for the treatment of this concentrate is done.

Jan 1, 2014

By B. S. Riess

A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process.

Aug 1, 2010

By A Frostick

Ranger uranium mine is surrounded by the World Heritage listed Kakadu National Park and offsite impacts resulting from mining at Ranger would affect the Magela Creek catchment first. Radionuclides, lead isotope ratios and metal concentrations were measured in sediment cores from the Magela Creek catchment around Ranger to investigate the dispersion of mine-derived particulates. The study found a localised area within the Ranger mineral lease, where upper sediments had elevated levels of radionuclides and trace metals and radiogenic Pb isotope ratios. There is no current evidence of sediment dispersion from Ranger further downstream within the Magela Creek catchment.

Aug 1, 2010

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By Michael S. Moats, Addin Pranowo, Gerardo R. F. Alvear F., Nigel Aslin

The toxicity of arsenic is well known and documented. However, the presence of arsenic in copper electrorefining anodes and electrolyte is critically necessary to produce high quality cathode. Arsenic as well as antimony and bismuth concentrations vary depending on their relative concentration in the anode copper received from the smelter. This paper will discuss the behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance. This will include the minimization and mitigation of problems associated with arsenic, antimony and bismuth including cathode contamination, floating slimes, scaling and anode passivation.

Jan 1, 2014

By M. Honarmand, Z. Moezifar, H. Ranjbar

Abstract - The Sar Cheshmeh area covers an area of 640 km2, and is located in the southern part of the Iranian Volcanic-Sedimentary Belt. ETM+ images have been used for alteration mapping. The Crosta method was found useful for enhancing exposed areas containing hydroxyl and iron oxide minerals. However, field checking has shown that this method is not able to identify all the known areas of hydrothermal alteration. Many of these altered areas are also not clearly resolved in the geophysical data. In order to improve resolution of such areas, integration of remote sensing and geophysical data may be helpful. The Darrehzar Cu deposit was chosen as a control area. The data have been divided into two sets: explanatory and target variables. The explanatory data are Landsat hydroxyl and iron oxide images and airborne geophysical data (K, U, and Th total counts, and total magnetics). The target variables are rock geochemistry and ground geophysics. Data analysis and integration of geophysical and remote sensing data were performed using directed principal components. This technique is found to be useful for the delineation of hydrothermally altered areas with more confidence.

Jan 1, 2002

By W. Geslin

Backward extrusion process is a metal forming process, which limits the manufacturing?s extra thickness when compared with classical die forging technique. Because of a lack of alloy?s mechanical behavior knowledge, the basic strategy of design is as follow: ?Definition of a small scale blank ?Performing experiment in order to get useful process data ?Improvement finite element simulation conditions ?Development of the full scale blank forming process (design of tools,...) using the finite element simulation A comparison between the result of modeling and the experimental data has been done to validate the finite element simulation.

Aug 1, 2010

By D. Embury

The construction and utilization of oil and gas pipelines is a vital aspect of the Canadian economy. The evolution of materials for this application can be considered as part of an evolutionary process in which the processing of the materials is linked to the design requirements of the pipeline. The evolution of both materials and designs will be considered in terms of parameters such as yield strength, work hardening characteristics including strain path changes such as the Bauschinger Effect and toughness. The final portion of the presentation will consider the possible uses of non-metallic materials, composites and 'smart 'systems in pipeline construction.

Jan 1, 2005

By X. B. Wang, Z. Q. Guo

Slagging coal gasification process became a highlight of coal chemical industry in China during the last decade. Refractory lining's life of slagging gasifiers is one of the most critical factors for a cost-effective operation. The paper introduces current status of coal gasification in China, lining structure of slagging gasifiers and performance of refractory lining. It also summarizes the major factors impacting on refractory wear in slagging coal gasifiers in four Chinese chemical plants, based on ten years of industrial experience. The utilizability is discussed in terms of cost-effectiveness of high chromia refractories and possibility of the alternatives.

Jan 1, 2004

By D. L. Chen, Q. Zhang

The effect of particle sizes on the low cycle fatigue (LCF) life of discontinuously reinforced metal matrix composites (DR-MMCs) has been widely studied. However, how the particle size affects the LCF life of DR-MMCs quantitatively is still lacking. The aim of this investigation is, therefore, to present an analytical model linking the LCF life to the particle size. This model, based on the enhanced dislocation density in the matrix and the load bearing effect of particles, showed that a decreasing particle size results in a longer LCF life, and the results predicted are in good agreement with the experimental data.

Jan 1, 2004

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By George P. Demopoulos, Amani Al-Othman, Terry C. Cheng

One critical issue in chloride hydrometallurgy is the regeneration of the lixiviant HCl that is currently achieved by pyrohydrolysis. In this paper, a low temperature HCl regeneration process was investigated which regenerates HCl and produces saleable gypsum. This process promises to reduce the generation of wastes by the reaction of spent calcium chloride leach liquors with sulfuric acid solution at low temperature. Experiments were performed to determine the optimum conditions of the reaction in terms of temperature, reagent concentrations, rate of reagent addition, mixing and seeding/recycling to produce marketable gypsum and HCl with practical strength.

Jan 1, 2004

By Bish Chanda

In the minerals business, like any other commodity-based business, management faces the daily challenge of holding down costs while the real prices of products are continually falling on an inflation-adjusted basis. Since the marketplace sets the prices, often without any premium attached for product quality, being one of the lowest-cost producers is the most viable competitive strategy. Continuous improvement is the mantra that can make the difference in terms of long-term survival of a mining company. Yet, this message has not always been followed, especially during periods of prosperity ushered by high commodity prices. More often than not, the need for improvement is only triggered by a crisis. This may be caused by events such as the onset of a severe economic recession, a prolonged oversupply situation due to an optimistic expansion of capacity during the period of prosperity, or simply falling profits alerting management to bring costs under control. At that time, there would be a need to implement a new cost-saving program, bring in a consultant to find ways to reduce costs, or re-activate an old program that had been shelved for some time.

May 1, 2003

By H. Saari, M. Pates, P. C. Patnaik, A. Merati

Single crystal nickel-base superalloys such as PWA1484 exhibit superior performance compared to conventional superalloys, and are used extensively in turbine blade applications requiring good high temperature properties. The life of these blades is typically limited by cracks and erosion. Due to the high cost of these blades, welding techniques are being considered to weld/repair worn components, extending their useful lives and delaying the need for expensive replacement components. However, the sensitivities for solidification cracking and post weld heat treatment cracking are relatively high in these alloys. Electron beam (EB) welding can deliver concentrated heat sources and has the potential to address these issues. Numerous welding trials and structural tests must be conducted to identify the optimum method and welding parameters. Weldability is studied over a range of material conditions, welding parameters, and directions. The influence of welding parameters on the fusion zone microstructure and resultant weldability is investigated using combination of microscopic examination and micro-hardness testing. This paper summarizes some of the results of a feasibility study conducted to understand the effects of welding parameters on localized microstructural features, cracking sensitivity, and mechanical properties of autogenously EB welded coupons of single crystal PWA1484.

Jan 1, 2004

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By Y. Sugiyama, K. Kitazono, T. Miura, K. Matsuo

"Impact energy absorbing system for automotive is an important technology. Open-cell porous aluminum alloys were manufactured through Powder Bed Fusion (PBF) process. Compressive properties of the porous aluminum alloy depend on the cell structure as well as the porosity. The authors manufactured two ordered cell structures, truncated octahedron and rhombic dodecahedron, and one disordered cell structure, random Voronoi structure using a 3D-CAD software. Compression tests revealed the anisotropic deformation of the porous aluminum alloy with ordered cell structure. On the other hand, the porous aluminum alloy with disordered cell structure showed relatively isotropic and uniform deformation, which is suitable for energy absorbing applications. Therefore, controlling the disordered cell structure designed by Voronoi diagram enables to develop the advanced porous aluminum alloy having various mechanical properties.INTRODUCTIONAdditive manufacturing (AM) process enables to manufacture near net-shape mechanical parts. The AM technology is typically focused on titanium alloys due to their high specific strength and biocompatibility (Attar, 2014). Recently, aluminum alloy parts can be manufactured through selective laser melting method (Leary, 2016). Metal foams or porous metals are lightweight cellular materials having closed-or open-cell structures (Banhart, 2001). Aluminum foams are focused on as an energy absorbing material for transport industries (Baumeister, 1997). The purpose of the present study is to investigate the optimal cell structure of open-cell porous aluminum alloy manufactured through AM process. Most previous researches on the AM aluminum lattice structure has been considered ordered and periodic cell structures. On the other hand, classical aluminum foams manufactured through cast or powder metallurgical processes have disordered and heterogeneous cell structures (Körner, 2000). The authors use a concept of Voronoi diagram (Moukarzel, 1993) in order to manufacture various cell structures."

Jan 1, 2018