Search Documents

By Z. Wu, L. N. Y. Wong

The present study develops the numerical manifold method (NMM) as a tool to investigate the progressive failure in rock slopes. The entire processes of the progressive slide surface development related to crack initiation, propagation, coalescence and degradation to eventual catastrophic failure are successfully captured. To overcome the limitation of the original NMM associated with an improper removal of the interface cohesion of the discontinuities, the displacement-dependent cohesion removal method is adopted. Simple examples of failure of rock slopes containing different arrangements of discontinuities are modeled and their results are compared with those based on the popular limit equilibrium method proposed by famous pioneers Jennings and Jaeger. In cases of coplanar non-persistent discontinuities, close results are obtained despite the differences in the consideration of the stress concentrations at the crack/discontinuity tips. In cases of non-coplanar discontinuities, since the influence of the tensile strength is considered by both the Jaegers model and the NMM, the Factor of Safety (SF) values are similar despite the difference in the failure path trajectories predicted by these two models. The results also reveal that the original NMM without the displacement-dependent cohesion removal method is always more conservative due to the improper removal of the interface cohesion. The displacementdependent cohesion method can to some extent alleviate such a limitation.

Jan 1, 2015

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

By J. Someehneshin

Nowadays along with population growth, industry development, consumption of mineral resources and the fact that the reserves on hand are running out, the depth of surface and underground mines for further exploitation are increasing. During recent years, in underground mining, the block caving method for low-grade and large-scale deposits has shown a growing rate of application. This method is very cost effective and economically affordable. The dimensions of blocks are one of the most important parameters which should be taken into account since it has been proved to have a great deal of effect on technical issues such as commencement of caving and mine design. Proper calculation of the length and width for a block in this method leads to proper caving and discharging which are the most important stages. Therefore, in this method, the calculation of the optimized dimensions (length and width) of blocks is not only important but also directly helps the productivity of extraction. In this study, firstly for the purpose of facilitation, some assumptions were considered and having used these assumptions for estimation of optimized length and width of block, a relationship based on rock mechanics and physics was explored. Furthermore, some necessary details were added to the said relationship and finally, it was transformed into an inequality. Solving this inequality provides us with the optimized length and width of the block. The explored relationship was analyzed with MATLAB software and the graphs thereof were drawn. In these graphs, each time one of the input parameters has been drawn up in a logical range so that it could be compared with previous states.

Aug 1, 2013

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By Yuwang Wang, Yanggeng Tan, Kezhang Qin, Zengqian Hou

Abstract- The large Derni Cu-Co (-Zn) deposit in Qinghai Province exhibits unusual geological features, and its genesis is controversial. Based on previous research and detailed field investigations, petrographic studies of the host volcanic rocks, isotope and trace element geochemistry of the sulfide ore, and comparison with typical ore deposits, this deposit is a VHMS (submarine volcanichosted massive sulfide deposit) type. This argues against previous interpretations of a magmatic or a hydrothermal replacement origin. Systematic rock, mineral and geochemical studies of the host serpentinites of the ore district indicate that the protoliths of several types of serpentinites that are widespread in the ore district are mainly ultramafic volcanic rocks. The mineralization formed within an ultramafic volcanic breccia, or between the breccia and its overlying Mg-rich carbonate rocks and volcanic sedimentary rocks. The ore-forming components were derived mainly from ultramafic rocks and partly from mafic rocks. The ultramafic rocks are MgO-rich, CaO-poor with a high MgO/FeO ratio, and the mafic rocks are rich in Na2O and poor in K2O. The chemical composition of the ultramafic rocks is similar to that of volcanic peridotite, or komatiite. The volcanic rocks that host the Derni deposit are among the most basic host rocks known for VHMS deposits, and the Derni deposit represents the most basic member in the VHMS deposit spectrum.

Jan 1, 2000

By C. Yoo

"Geosynthetics engineering has made phenomenal advances during the last decade in areas of manufacturing as well as practical applications. As a result, geosynthetics are now being recognized as essential construction materials that can be used to facilitate construction, ensure better performance of the structures and reduce the long-term maintenance in routine civil engineering works. The creative use of geosynthetics in geo-engineering practice is expected to continuously expand as innovative materials and products are becoming available. In this paper, a wide variety of geosynthetic products available to geoengineers to solve a wide range of problems are briefly presented along with their functions and possible applications. Fundamentals of geotextile filter design principles are then introduced for use in the tunnel drainage system. Practical applications of geosynthetics relevant for tunnel engineering are also highlighted with emphasis on the issues associated with the geotextile filter application for use in the tunnel drainage system.INTRODUCTIONGeosynthetics have emerged as essential engineering materials in a wide range of civil engineering applications, e.g., transportation, geotechnical, geoenvironmental, hydraulics, and private development since the first geosynthetic conference in Paris, 1977 (Koerner 2012). Due to their costeffectiveness, ease of installation, and well established mechanical and hydraulic properties, geosynthetics are now playing important roles in the field of geo-engineering.As indicated in the 9th Bucahanan Lecture paper by Holtz (2001), major developments in civil engineering have only been possible with the parallel developments in the technology of construction materials. For example, larger scale structures became possible with the help of developments in concrete, reinforced concrete, and prestressed reinforced concrete technology which replaced wood and building stone as construction materials. The best example of a parallel development in geo-engineering between the material and the geotechnical application may perhaps be the soil reinforcement technology which has a direct analogy with reinforced concrete as a polymeric reinforcement material provides added level of tensile resistance and stability to soils that have little to no tensile strength, thus giving additional margin of safety."

Jan 1, 2015

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By E. M. Yates, H. M. Hamilton

"For the assent of any new mining project it is essential to determine a realistic value of revenue from the sale of concentrates.A description of the market factors influencing the concentrate terms will be presented along with a detailed review of historical terms of a smelter contract for zinc concentrates. OverviewFor the assessment of any new mining project it is essential todetermine a realistic value of revenue from the sale of concentrates.This applies at all stages of assessment through to the final feasibilitystudy. In forecasting revenue for a zinc mine the followingfactors must be considered:(a) mill recovery and zinc concentrate grade;(b) metal price forecast for all payable metals;(c) smelter terms; and(d) other selling costs.Normally, data from test work are used to determine mill recovery and concentrate grade.Market forecasting, and indeed all economic prediction is an inexact science and probably will always remain so. We have our econometric models our input/output models and a lot of other tools. But they are of no help in predicting the unpredictable. OPEC's huge increase in the price of oil was certainly the most dramatic example of this. It had a tremendous effect on the cost of producing most products world wide and on the price of these products. Any forecasts made prior to the OPEC action were obviously proven wrong."

Jan 1, 1994

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939

By I. S. Zajac, Y. O. Oyediran, M. C. Robart

This paper presents an overview of the metallurgical work on the Strange Lake Alkalic Complex (SLAC), from historical development of the "Main Zone" to present day develoment of the "B Zone". The SLAC, originally discovered by the Iron Ore Company of Canada (IOC) in the northeastern Canadian Shield of Québec and Labrador, is one of the world’s largest deposits of rare earth elements (REE) including yttrium and high field strength elements (HFSE) including zirconium, niobium, and titanium. It is part of a Precambrian, post-tectonic complex of peralkaline granites which intruded along the contact between gneisses and monzonites of the Churchill Province of the Canadian Shield. Mineralization of interest at Strange Lake principally occurs within peralkaline granite-hosted pegmatite and aplite sheets and, to a lesser degree, within the host granites, particularly in intra-pegmatitic granites. The highest grade and metallurgically most favorable mineralization is in the upper, open pit mineable parts of the SLAC. Metallurgical development has been conducted under a number of mining companies, and various value metals have been targeted throughout the history of the deposit, including yttrium, zirconium, niobium, and rare earths. Historic processing routes tested have included ore beneficiation, atmospheric leaching, solvent extraction (SX), and metal precipitation. This paper also presents the metallurgical development supporting Quest Rare Minerals Ltd.’s (Quest) 2013 Pre-Feasibility Study (PFS) and 2014 Preliminary Economic Assessment (PEA).

Jan 1, 2014

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By George P. Demopoulos

In a departure from the traditional domain of hydrometallurgical extraction processes we consider new R&D opportunities for innovative application of solution processing into the advanced green energy and clean technology fields. It would not be an exaggeration if we state that protection of the environment via advancement of clean technologies on the one hand, and harvesting and utilizing renewable energy in a sustainable and cost-effective way on the other hand are clearly among the top pressing global priorities. When hydrometallurgy is approached on the basis of its aqueous chemistry and reactive processing fundamentals, it can indeed provide a highly fertile ground for innovation outside the "box". In this context therefore we will present highlights from our recent research that is directed towards the development of new generation HCl recycling, environmental, and solar energy conversion/storage technologies. In all systems the research is approached via the innovative integration of aqueous process engineering and material chemistry principles. The presentation will include discussion of (i) the development of crystallization-based HCl regeneration technologies; (ii) the supersaturation-controlled production and encapsulation of scorodite that was recently commercialized; (iii) the aqueous synthesis of nano-TiO2 and its electrophoretic deposition into solar cell electrodes; and (iv) the hydrothermal synthesis of nanostructured lithium titanate and lithium iron phosphate materials to make lithium-ion batteries destined for electric cars.

Jan 1, 2014

By Lorant B. Geller

Sixteen miners died tragically at the Paymaster gold mine at Timmins, Ontario in February, 1945, when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (Investigations, 1947) aimed at avoiding future disasters of this kind. One consequence was the development, and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the nondestructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990 and 1992, Geller and Kitzinger, 1991, Geller et al., 1993). Since the mid-1990s particular attention was paid to the design and operational results obtained from the computer- controlled portable MagnographJ II wire rope tester (Geller et al., 1995 and 1998). In the present article the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the PermaScanJ testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remotecontrolled instrument described in this paper has now been in operational use for more than 4 years.

May 1, 2003

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By Elhachmi Es-Sadiqi

"For over 40 years, CANMET has focused its research on value-added products and energy efficiency in the metals industry. The Efficient Metal Production Program is currently managed by Dr. Elhachmi Es-Sadiqi, and the Canadian steel industry is its main client — both directly and through international organizations such as the American Iron and Steel Institute (AISI) and the International Lead and Zinc Research Organization. AISI membership includes Canadian steel companies IPSCO, Dofasco, Stelco, Algoma Steel and Sidbec Dosco.Canada’s steel industry makes important contributions to the economy. The industry comprises 14 companies and employs 33 600 people in locations such as Sydney, Nova Scotia; Tracy, Quebec; Selkirk, Manitoba; Saskatoon, Saskatchewan; and Sault Ste. Marie, Ontario. With annual production at about 16 million tonnes, sales in 1995 totalled $11 billion, $3.8 billion of which was exported.Canada’s steel industry supplies the transportation, oil and gas, appliance, packaging and construction industries. It is at the forefront of new technology use and has a substantial support network to provide raw materials, equipment and service. Three main segments of the industry include flat-rolled products (e.g., plate and sheet steels), long products (e.g., concrete reinforcing bar and structural steel), and specialty and alloy steels (e.g., stainless steel and tool steels, in both long and flat products)."

Jan 1, 1998

By Rebecca L. Jones

The paper addresses the application of XPAC AutoScheduler at the Fort Hills Energy Oil Sands Project to complete fast turn around ?what if? scenario testing of different mine schedules. Traditional scheduling approaches involve engineers making a ?best guess? at the required mining sequence, loading this sequence into a scheduling package and testing the results to determine if the schedule meets corporate objectives. This process is iterative and can be very time consuming. Autoscheduling techniques, on the other hand, are based on the engineer pre defining the mining rules and constraints of the deposit. The software then automatically selects a sequence of mining which the schedule should try and achieve, based off specified corporate objectives. Under this system the engineer is able to adjust the objectives and rules to evaluate numerous scheduling scenarios quickly and easily. An XPAC AutoScheduler model was built, documented, and implemented by Runge and Petro-Canada Oil Sands Inc. personnel in a month. It is currently being used by Petro-Canada Oil Sands Inc. to run multiple schedule scenarios, most taking less than ten minutes configure and ten minutes to schedule. The results of each schedule are tabulated with supporting graphs on; the bitumen grade profile, strip ratio, ore inventories and mined tonnage. In addition to this, the block model may be animated to show the progression of the resources mining the schedules.

May 1, 2008

By Donald J. Farrish

"Mr. Chairman and fellow CMP members, most of these remarks will be made with particular reference to copper concentrate but the basics apply generally to other metal concentrates as well.For very good reasons, using copper as an example, smelting capacity usually is located either close to mine production or close to areas of high copper consumption. The mine producer can add on smelting capacity to insure that the copper in his concentrate can be processed into a marketable form under more or less controlled conditions including costs. On the other hand, the consumer wishing to assure a better supply of copper likewise can build smelting capacity and offer treatment charges attractive enough to discourage mines from investing in their own facilities. In this regard, freight is an important factor. Bulk shipments from the heart of Africa with a large overland component are uneconomic whereas concentrate movements from Australia or South America compare favourably with smaller metal shipments.A mine project which incorporates smelting capacity, will often, through the presence of this capacity, encourage active exploration and development of additional concentrate production in the vicinity. The usual result is that new mines within reasonable distance of the smelter will be able to avoid the capital required to build their own smelting and refining facilities and that the existing facilities will expand to appreciate economies of scale."

Jan 1, 1978

By Ken G. Stowe, Stephen L. Chryssoulis, Joe Y. Kim

"Lead ions originating from galena during processing of complex sulphide ores migrate to ""cover"" the surface of sphalerite and iron sulphide mineral rarticles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead activated minerals float in the Cu/Pb circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead- activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide rarticles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.IntroductionSurface properties play a critical role in many aspects of mineral processing such as flotation, flocculation, etc. An understanding of interaction mechanisms of different reagents (inorganic cations and anions, collectors, regulators, etc.) with mineral surface in an aqueous solution is a very important pre-requisite in achieving the desired selective flotation. In the flotation of complex sulphide ores, the flotation collectors respond to the activation of minerals such as sphalerite, pyrite etc. by heavy metal ions of Cu, Pb or Ag, which is a strictly surface phenomenon."

Jan 1, 1995

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011