Search Documents

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By Jean-Luc Collins

"The paper deals with the impact of fleet imbalance on a deterministic evaluation of shovel fleet productive capacity. It shows that if the fleet imbalance is overlooked, then estimated fleet productive capacity will be overrated.The paper shows that fleet imbalance inflates utilization, and care must be taken when using such statistics which are derived from reported field-equipment-hours. It shows that the utilization must be deflated by a factor called 'balancing efficiency"" in order to estimate shovel productive capacity correctly. The paper also shows how fleet imbalance can be controlled by managing idle time or downtime in an actual operation.The technique used for measuring the balancing efficiency factor is based on statistical analysis of equipment utilization."

Jan 1, 1980

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By Cheryl L. Allen

The power required to operate a ventilation system can be 25% to 50% of the total energy requirements of a mine. In an effort to reduce energy consumption, initiatives are being introduced at Vale Inco to increase the efficiency of ventilation systems with the objective of decreasing energy usage. One energy conservation measure being introduced is the use of variable frequency drive (VFD) technology for fan motor control. Advancement in technology is making VFD applications more of a standard in industry. The benefits include improved operating performance and system control, reduction in current peak demand, and optimized power usage. This paper describes the application of VFDs for main and auxiliary mine fans; and associated potential energy savings.

May 1, 2009

By A. Cadieux, J. -B. Pineault, C. Allaire

The temperature measurement of the molten metal in the aluminum transformation process is of prime importance. This is particularly the case for aluminum treatment furnaces, such as holding and melting furnaces. Such reverberatory type of furnaces involve a thermal gradient across the metal line which limits the life of conventional thermocouple protective ceramic shields, due to the action of locally induced thermal stresses. This paper presents a novel thermocouple assembly using a composite refractory protective shield allowing long term resistance to such above conditions. Example of results obtained from various tests in aluminum holding furnaces are presented. The results confirm the superiority of the novel thermocouple assembly, as compared to conventional thermocouple units.

Jan 1, 2004

Mining Association of Canada ! Represent base and precious metal, diamond and oil sands producers as well as nonferrous metal smelting and refining ! Member companies account for the vast majority of Canada?s mineral and metal production ! Mining is a major economic sector in Canada ! 13% of total exports ($47 billion) ! Employment near 400,000 ! 4% of GDP The Kyoto Protocol ! November 18, 2004 -- Russia deposited its instrument of ratification with the United Nations ! The Kyoto Protocol entered into force on February 16, 2005 ! The Kyoto Protocol is now an international and legally binding agreement to reduce GHG emissions world wide ! Canadian GHG target = 6 percent below 1990 ! First Commitment period 2008-2012

Apr 1, 2005

By T. Cutard, H. Marzagui, E. Ouedraogo, M. Roosefid, M. Prompt, C. Deteuf

The present work is achieved in the framework of a French national program on modeling and experimental characterization of the thermo-mechanical properties of refractory materials (PROMETHEREF). This research program is aimed to establish fair models and experimental database and to make it available to industrial partners for numerical simulation of industrial structures made of these materials. The present paper focuses on two silica-alumina refractory castables, an andalusite based one and a bauxite based one. We will present the first rheological characterization results achieved at room on normal and preheated samples of these two refractory castables. Refractory castables are characterized with the help of four points bending tests, compression tests and tensile tests.

Jan 1, 2004

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By J. Suarez

The innovation initiatives for world-class mines today and in the future focus on automation and robotics in equipment and machinery. These innovations have benefited from the development of advanced tools in global positioning, the Internet, the capabilities of data storage, transmission and handling, and intelligent systems. Forward-thinking companies have been investing in automated trains and trucks, selfdrilling rigs, intelligent flotation systems, etc. Considering that the emphasis has been mostly laid on improving the performance and reliability of the equipment and machinery, it is not surprising that the visibility was geared toward mechanical, electrical, process, and metallurgical engineering. One of the critical disciplines, mining engineering, has had less shine from the spotlight of automation and robotics. Mining engineering is concerned with the design, the operation, the management, and the reclamation of mines and mining facilities. In essence, it does benefit from the advantages of automation and robotics in equipment and machinery. However, being ?left out? in the innovation process may impede the core capabilities of this engineering discipline, which would create a two-tier knowledge and technology system in mines. For example, shovels in an open pit may be equipped with technology that can send real-time data of actual payload, number of buckets, mechanical status, etc. But, are mining engineers aware of the possibility to incorporate the data into their planning tools in order to have updated forecasts and accurate information? And if they are, are they equipped with the tools to reap the rewards of those technologies? And if so, is the personnel trained to use the tools efficiently? This paper is a contribution to the discussion on the technological advances in mining engineering. For the authors, the roadmap to the future requires a smart integration of technological advances in hardware and software so that mining engineers are not only aware of the possibilities, but also trained and capable of using the available tools. Essentially, this paper believes that automation and robotics in equipment alone will be undervalued and underutilized if the owners and drivers of the mining systems (i.e. the mining engineers) do not possess the tools and training to integrate the technological advances into the functions of mining engineering. The intent of the paper is to analyze the available technologies for the core mining engineering functions of design, planning, scheduling and optimization. The analysis will lead to discussions and suggested solutions on integrative technology solutions that would create optimum value for the mining processes and equipment technologies.

Aug 1, 2013

By C. Pawlik, R. T. Jones

Cobalt occurs together with copper in the southern African copper belt, and a large portion of this cobalt ends up in copper smelting slags, mostly dissolved in oxide form. It is possible to achieve high recoveries of cobalt by reductive smelting of the copper slags, using some form of carbon as a reducing agent in an electric furnace. For example, a 40 MW DC arc furnace was operated at Chambishi Metals in Zambia from 2001 to 2008, and demonstrated cobalt recoveries of around 80% from slag to an iron-rich alloy containing copper and cobalt. The alloy was atomized prior to leaching. With the recent increase in demand for cobalt (and the resulting high metal prices), there has been increasing interest in this process route. There is also an alternative hydrometallurgical process for recovering the valuable metals from the slag. The choice between these process options requires a trade-off between capital and operating cost and environmental acceptability. This paper examines the potential for cobalt recovery from slags, and outlines various process options. INTRODUCTION Cobalt has had a number of important uses in society since antiquity, and its principal use has changed dramatically over time. Since at least 2250 BC, cobalt-based pigments (cobalt blue) have been widely used to colour manufactured goods such as glass and pottery. Later, cobalt became known for its magnetic and wear-resistant properties and high-strength alloys, and most of the cobalt produced was consumed in the production of cobalt-based superalloys. The greatest recent growth in cobalt demand is due to it being essential to the rechargeable lithium-ion batteries used in consumer electronic devices and increasingly to drive electric vehicles. Cobalt is usually produced as a by-product of copper or nickel. The copper belt in the Democratic Republic of the Congo (DRC) and Zambia supplies most of the world's cobalt production. In 2018, the DRC was expected to produce 90 000 tons of the world total of 140 000 tons of cobalt (Shedd, 2019). This paper focuses on the southern African copper industry, and specifically the cobalt that is able to be produced as a co-product from this. A BRIEF HISTORY OF SOUTHERN AFRICAN COPPER SMELTING Copper deposits in South Africa have been documented since at least 1685, when the Cape governor, Simon van der Stel, ‘discovered’ the 'Copper Mountain' at Springbok. South Africa's first public commercial mining company (imaginatively called the 'South African Mining Company') was established in Cape Town in 1846, to exploit the rich copper resources that were believed to exist in Namaqualand.

Jan 1, 2019

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By C. M. Acuna, M. Sherrington

In high temperature processes thermodynamic equilibrium is assumed and therefore chemical potential of elements, among the condensed phases, have to be the same. In such situation impurities distribute accordingly and their fractional distributions are affected by the masses of the coexisting phases. It has been claimed Teniente Converters perform quite well for smelting high impurity concentrates, especially in respect to volatilization and/or slagging. Production of high matte grade near white metal composition, requiring moderate oxygen enrichment in the process air, results in a huge mass of gas and therefore a high fraction of impurities report to it. Similarly, by recycling different sources of slag, flue dust or other materials, the mass of the final slag is increased and so do the masses of impurities reporting to the slag. Nevertheless, above a certain level the recycling of smelter byproducts is no longer feasible and the cycle has to be halted, unless higher impurity mattes are accepted. Although the process might be continued during converting and refining, lengthy and expensive measures have to be taken if suitable anode copper for electrolytic refining is to be achieved. In the present study samples of high arsenic matte grade and slag were obtained on a pilot scale. The matte samples, on the order 75%Cu, were equilibrated with slag at varying ratios in magnesia crucibles under CO/C02 atmospheres at 1523 K. After 24 hours equilibrium matte and slag were rapidly solidified and analyzed by copper, sulfur, iron and arsenic. Furthermore, industrial samples of matte and slag, in the order 75%Cu at 1523 K, were obtained via a special quenching sampling device to determine the association of copper and suspension of matte and copper in slag. Based on the results, the distribution coefficient of arsenic between slag and matte was evaluated along with copper species in slag and the fractional distribution of arsenic, in the coexisting phases, was determined as a function of the ratio mass of slag to mass of matte.

Jan 1, 2007

By G. S. Hume

Introduction O WING to the mineral discoveries which have recently been made in the Great Bear Lake region and the possibility of the need for fuel for transportation and development, it seems.timely ro review available information regarding the oil prospects in the vicinity of Great Slave lake and Mackenzie river, where a vast area is underlain by Palreozoic and younger sediments that undoubtedly are petroliferous. Exploratory surveys were carried out in this area by the Geological Survey and others in the latter part of the 19th century, but it was not until 1920, when drilling for oil actually began, that any serious attention was paid to the oil prospects. This is readily accounted for by the remoteness of the region, the lack of quick transportation facilities, and the shore summer season. Numerous and copious oil seepages had been reported, however, from widely separated localities, and interest was stimulated by the knowledge that these occurred in Devonian strata which had given a remarkable record of sustained production of high-grade oil in the oil-fields of southwestern Ontario. . Accordingly, during the four years 1920 to 1923, inclusive, several parties sent out by the Geological Survey made as thorough an investigation of various parts of the area as seemed warranted at that time, and from these surveys most of our information regarding the details of the stratigraphy is derived. In such a large area, it is inevitable that the lithology and thickness of rocks of the same age would show wide variations, and hence it should be recognized that conditions as regards oil prospects in the vicinity of the west end of Great Slave lake are quite distinct from those that occur near Fort Norman, 400 miles farther to the northwest, and these again are in all probability quite different from those in the less well known Arctic Red River area, 250 to 300 miles still farther north.

Jan 1, 1932

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By N. Hwang

There has been increasing interest in the use of robotic machines, and several prototype robotic machines have been developed to automate the grit-blasting process for the purpose of steel bridge maintenance. To utilize such a robotic grit-blast machine effectively, the first consideration is automating the determination of the rust surface area to blast, on the basis of standards of practice, in a rapid manner. This study aims to propose a method to rapidly and accurately determine the rust surface area on steel bridges to blast, with consideration for the standards of practice, from images acquired via a blasting machine. The first step is to perform a color space conversion to transform the input image from a red/green/blue (RGB) color space to a hue/saturation/intensity (HSI) color space. The next step is to detect the presence of rust, using pixel-level classification via the C4.5 decision tree algorithm. Then it is necessary to confirm the blasting area by verifying whether the rust detection result satisfies the specified criteria on the basis of standards of practice. The proposed method was validated on 39 test images with various characteristics with respect to the degree of rusting and rust distribution type. The experimental results showed that the average accuracy rate of rust area classification was about 97.63%, and the success rate of the final decision of blasting area determination was 100.00% for 39 test examples. The whole processing time took an average of only 0.86 seconds per image. The preliminary results demonstrated that the proposed method not only determined whether rust was present in an image and the amount of rust but also indicated whether blasting was necessary, and, if necessary, it rapidly specified the rust surface area that should be blasted on the basis of standards of practice. The proposed method could be successfully incorporated into a robotic grit-blast machine.

Aug 1, 2013

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016