Search Documents

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By S. C. Livanou, S. P. Tampouris, E. N. Zevgolis

In ferronickel (Fe-Ni) production from oxidized nickeliferous ores, mechanical losses of ferronickel in the slag are reduced by magnetic separation. Slag from the electric furnaces (E/Fs) contains 0.16% Ni. Its magnetic separation gave a pre-concentrate with 0.76% Ni, weighing approximately 6.5% of the feed. Nickel recovery was 29.7%. This pre-concentrate was then treated in a second (concentration) plant. Concentration treatment involves screening, crushing and magnetic separation. A pre-concentrate with 0.76% Ni gave a magnetic concentrate with 2.58% Ni and a non¬magnetic part with 0.35% Ni. Smelting of the non-magnetic part without the addition of a reduction agent in a laboratory electric arc furnace, gave a ferronickel alloy with approximately 20% Ni and a slag with 0.16% Ni.

Jan 1, 2005

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By S. Gößling-Reisemann

Most copper ores contain valuable co-products such as molybdenum, gold, silver, nickel, etc. Sulphuric acid and steam are valuable by-products, which are generated dur¬ing copper production. The environmental impacts from mining and refining therefore need to be shared between these by-products and co-products, an issue in Life Cycle As¬sessment (LCA) referred to as allocation. There are different, recognised methodologies for doing so: burdens can be allocated based on the market values of these commodities, they can be allocated by mass, volume, molar amount, functionality, or other physical, technical or economic factors. All of these methodologies have their respective merits and restrictions, and the choice is usually case specific. Nevertheless, the choice between alternative methodologies can have dramatic effects on the LCA results. Recycling in LCA has to be handled in a similar way, as it essentially constitutes a special case of co¬production. The existing standards (ISO 14040 ff.) allow different methods for imple¬menting recycling and allocation into metal LCAs (open loop, closed loop, value cor-rected substitution, etc.), which are still a subject of discussion in the scientific community. However, the methodology used can significantly influence the ecological profile of copper and copper products. We will present an overview of the different methodologies available for including recycling and allocation and give an analysis of how the meth¬odological choice affects the final LCA results. This work will be followed up by quantitative case studies.

Jan 1, 2007

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By Z. Sun

The hydrogen embrittlement and stress-corrosion cracking (SCC) behavior of an a -titanium alloy and its two kinds of welding samples have been investigated. The results show that this alloy has very low susceptibility to SCC, and the values of Kiscc for the alloy are 46.4 MPa ? m' 65.86 MPa ? mu2 in the direction of T-L and L-T, respectively. The scanning electron fractographs show transgranular and quasi-cleavage fracture. The hydrogen embrittlement results show that the notch sample of the alloy is not sensitive to hydrogen, but the electro-beam welding and diving-arc welding samples are sensitive.

Jan 1, 2005

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

By H. G. Ames

"The property of Perron Gold Mines, Limited, lies in the southwest corner of Pascalis township, northwestern Quebec. It is approximately 12 miles northeast of the town of Val d'Or.This ground was originally staked by Jack Mathews of Amos in the spring of 1931. Shortly after staking, a quartz vein containing visible gold was uncovered on the south boundary of the property, about 400 feet south of the present shaft. With further prospecting, another spectacular goldbearing vein was found 3,000 feet northwest of the original showing. Subsequently, several programmes of exploration were carried out in search of the main ore zone. By 1933 sufficient ore was outlined to warrant sinking a shaft. The first ore was milled in 1934.Total production from the Perron mine from commencement in 1935 to 1944 has been 317,900 oz. gold having a value of $11,935,106. The average recovery a ton for 1944 was $9.01."

Jan 1, 1954

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami, G. P. Cole

"The past several decades have seen a steady increase in the use of atmospheric monitoring systems (AMS) in underground mines as sensor technology has advanced and costs for this technology have decreased. The AMS is a reliable tool for early mine fire warning by detecting gaseous products of combustion in underground mines. During a mine fire emergency, mine decision makers rely heavily on the prompt and accurate knowledge of the ventilation and fire situation in the mine, such as fire location, fire size, and the spread of smoke to make effective and efficient decisions on firefighting strategies and miner evacuation. Meanwhile, a prediction of the potential for fire development at a later time, such as whether the currently designated mine escapeways will be contaminated by smoke and toxic gases with the progress of the fire, is critical for effective decision-making to save lives that are in danger. The AMS monitoring data, including carbon monoxide (CO) concentration, airflow rate, smoke, etc., can provide information as to whether the smoke has reached the locations where AMS sensors are installed and if a mine-wide smoke spread has occurred. The National Institute for Occupational Safety and Health (NIOSH) has undertaken a task to integrate real-time AMS monitoring data with the mine fire simulation program, MFIRE, to simulate and predict the spread of smoke and toxic gas in a ventilation network based on the real-time AMS data. This paper reports the developed real-time method for characterizing the size and location of an underground mine fire and for predicting the spread of contaminants throughout the mine ventilation network using sensor data from the AMS.INTRODUCTIONNIOSH conducts research to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in underground mines. The advancement of senor technology and the increasing demand for real-time mine parameters monitoring have led to extended applications of atmospheric monitoring systems (AMS) in underground mines worldwide. In the United States, AMS is primarily used for early mine fire warning by detecting carbon monoxide (CO) in fire hazard areas, such as belt entries. Mine fires can grow rapidly, and time is the critical element. Prompt detection, timely and accurate warnings to those miners potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground mine fire (Conti et al., 2005). The early detection of a mine fire could gain time for the first responders to put out the fire before it develops into a disaster. An AMS system with CO sensors has especially played an important role in the early detection of mine fires. The continuous monitoring of an underground mine atmosphere with an AMS could generate a large amount of data in a mine fire event. However, the current application of AMS is mainly limited to sending out an alarm when monitored CO concentration exceeds a certain level. An opportunity arises as to whether these data can be further used in fire emergency response. In order to make effective decisions on firefighting strategies, mine workers’ seeking refuges, evacuation and escape, and the timing on when to send rescuers, decision makers need accurate and timely knowledge of the ventilation and fire situation in the mine. Information about the fire intensity, where in the mine the smoke and toxic gases have spread, and whether designated mine escapeways have been compromised by smoke and toxic gases from the fire would greatly increase the effectiveness of these decisions. However, the monitored AMS data only provides atmospheric conditions in the vicinity of sensor locations. What is concluded from the monitored AMS data highly depends on the decision makers’ capability and experience. Predictive insight into fire growth and smoke transport would greatly help decision makers during a fire emergency."

Jan 1, 2019

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008