Search Documents

By M. Coleman, M. E. Reed

The control of feed delivery quality to the flash furnace remains an unsolved problem. Many operations around the world still have limited control of feed quality to their flash furnace. Schenck Process and WorleyParsons continue to work towards the ‘holy grail’ of simple quality feed delivering both radial feed distribution and pulseless feed delivery. Ten years ago they joined forces to offer a system based on then Clyde Process RotoFeed system which could deliver ground level installation, online mixing of materials, pulseless feeding direct to the burner, with good radial distribution. Unfortunately, this proved to be too large a step for the Flash Smelting community and met with resistance from the process owners. Since then the community has developed a range of options some of which have been implemented over this period. Despite these improvements there are still areas of concern including safety issues associated with concentrate leaks and spills, uncontrolled variations in feed rate including massive flooding events, intermittent distribution improvement and set up of the burner continues to be trial and error and hard to repeat the success in each burner campaign. These continue to impact flash furnace performance globally on a daily basis. Following the community reticence to pursue the complete solution a number of interim steps are now available to pave the way to the ultimate feed system. The mixing of material has been installed and is delivering line blended materials on a daily basis. This paper will investigate the developments over the last 10 years and discuss the pros and cons of this incremental step process for overall furnace control. INTRODUCTION Schenck Process and WorleyParsons have continued to interact and observe changes in the flash smelting industry and to consider application of the Clyde RotoFeed now incorporated in the Schenck Process ProStreamTM range for delivery of feed directly to the concentrate or matte burner. Schenck Process pneumatic injection from the Clyde Process range, ProStreamTM, utilises two types of volumetric feeders to accurately control the feed of material into an injection pipeline. These are referred to as the RotoFeed and RotoScrew technologies and the choice of feeder type is dependent on the characteristics of the material to be handled. The RotoFeed is generally used for finer, granular and powdered materials which cannot be accurately handled with a screw such as pulverised coal and copper concentrate, whilst the RotoScrew is particularly suited to coarser lump materials, particularly abrasive of cohesive materials like zinc powder, electronic scrap and metal ashes. Both units can operate at high pressures and many systems work at 3 to 10 bar with the occasional system working at 20 or 30bar for carbon to gasifiers. For the Flash furnace the ProStreamTM units can be used to deliver each of the furnace feed materials into a single line, mixing the materials homogeneously and live to the burner.

Jan 1, 2019

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By M. A. Kelly

Pit Optimisation using the Lerchs Grossman algorithm has been successfully applied in many deposits. Pit shells often form the basis for scheduling. Pre-assigned costs may not accurately reflect the costs that strategic scheduling decisions are based on. This can affect all mines, but is particularly true for commodities requiring blending. Adoption of Maximiser technology addresses these cost based scheduling and blending challenges.

May 1, 2007

By M. K. Kim

This study presents a framework for quality inspection of precast concrete components using the 3D laser scanning technique. As precast concrete-based rapid bridge construction is getting standardized, quality assessment of the precast concrete becomes critical for preventing any failures during the construction process. Moreover, as Building Information Modeling (BIM) gains popularity in the construction industry, autonomous and intelligent inspection systems are needed. Current method for quality control of precast concrete components, however, heavily relies on visual inspection and contacttype measurements, which are time and labor demanding. Also, storage and delivery systems of inspection information such as the procedures and results of quality inspection are lacking. To overcome these limitations of the current quality assessment technique for precast concrete, this study aims to develop a BIM-based framework for efficient quality inspection of precast concrete with the use of a 3D laser scanner. First, we formulate practical guidelines including detailed inspection procedure, selection of optimized scanner and scan location, inspection criteria, and data storage and delivery system. Second, to investigate the applicability of 3D laser scanning to precast concrete quality inspection based on the proposed framework, a case study inspecting quality of a lab-scale object assumed as precast concrete component is presented for detecting defects.

Aug 1, 2013

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By Brian McIntrye, Bo Trygg

"The need for grinding mills of ever increasing capacity and greater feed openings has tended toward mill trunnion diameters being beyond the size limits for roller bearings.Hydrodynamic plain bearings need to be wide enough to achieve the necessary bearing pressure in order to obtain an oil film with sufficient carrying capacity at low rotational speeds. This greater width increases edge loading resulting from the deflection of the mill under load.Because of the high surf ace pressure involved, the life of support rollers and girth rings is often inadequate-fatigue leads to flaking on the contact surfaces. Heat treatment of the girth rings also has its problems.The hydrostatic shoe bearing permits unlimited trunnion diameter and a high carrying capacity. The self-aligning shoes compensate automatically for radial deviations and large deformations can be tolerated at the girth ring.The sliding surfaces are completely separated by oil under pressure, enabling negligible starting torque and good damping capacity to be achieved together with low rotational speeds.IntroductionHydrostatic bearings have been known within machine technology since 1865, when the Frenchman Girard received a patent for such a bearing. During the following 75 years, these types of bearings were used sporadically for thrust bearings, primarily in water turbines. The first usable radial bearing was not designed until 1938. Since the 1950s, when hydrostatic bearings started to come into use within the field of machine tools, extensive research and development work has been carried out at various institutions and research centres throughout the world. Many support problems are now solved by means of hydrostatic plain bearings and the primary factor in deciding to use them is their unique characteristics:• ability to carry high loadings• no starting torque• large damping capacity• no wear• large running accuracyThe hydrostatic shoe bearing has been developed specially for use in the heavy machine industry, with the requirements for high loadings and large support diameters which this market demands."

Jan 1, 1982

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations addressing hoist safety, automatic hoisting, and shaft obstruction. The regulations are quite similar among provinces, with only slight differences. Risk-mitigation strategies used in other industries are discussed, including their applicability to mine hoists. The specific case of software safety is introduced through examples. The mitigation of software failure is based on the use of the software lifecycle as recommended by the International Electrotechnical Commission (IEC) 61508 standard. Finally, ways to improve hoist safety are proposed.RÉSUMÉ Le présent article compare entre elles les diverses réglementations provinciales canadiennes concernant la sécurité des machines d'extraction, le levage automatisé et les obstructions dans les puits. Les réglementations sont assez semblables entre les provinces, mais elles comportent de légères différences. Les stratégies d’atténuation des risques utilisées dans d’autres industries sont abordées, incluant la possibilité de les appliquer aux treuils de mines. Le cas spécifique de sûreté des logiciels est abordé par des exemples. L’atténuation de la défaillance des logiciels est basée sur l’utilisation du cycle de vie du logiciel, comme cela est recommandé par la norme 61508 de la Commission électrotechnique internationale (CEI). Des moyens d’améliorer la sécurité des treuils sont également proposés."

Jan 1, 2016

By J. G. Ross

A DESCRIPTION of the block-caving system of mining as practised at the King mine of Asbestos Corporation, Limited, Thetford Mines, Que., was presented. at the Annual Meeting of the Institute held in Quebec city, in April, 1934. The paper was published in the Transactions of the Institute for 1934. There has now been recovered, by this method, one million tons of ore, and a review of experience indicates that the method was well planned and has been executed smoothly. In approaching the problem of selecting the type of mining best adapted to this deposit, the method had to be one which would be low in cost, use no wood, and not disturb the surface immediately bounding the ore-body on two sides. Prior to 1931, block-caving had been considered but rejected, as it en-tailed disturbance of the surface area which lay within a 45° angle of the lowest contemplated workings, if the practice of such mines as Ray, Miami, Inspiration, and Morency, where this type of mining has been used extensively, was followed. At these properties there have been mined large tannages at outstanding low costs, but an extensive surface area has been disturbed in each case. In some instances, townsites in the mining area have had to be abandoned, and dwellings, not considered worth moving, have been allowed to fall into the depression. A study was made of the principles involved in the various types of block-caving, the existing information on ground movement, subsidence, etc., also being carefully analysed. Toward the end of 1931, a plan was conceived whereby the country adjoining ground being caved might be held permanently in place and undisturbed. The success of such a scheme was essential to the application of block-caving at the King mine on account of property boundaries, the Quebec Central Railway right-of-way, and expense of moving buildings. Study of existing data on caving and movement of rock, caused by sub-surface excavations of sufficient unsupported area to result in failure of the backs, indicated, in practically every instance, that such movements followed certain definite laws of mechanics.

Jan 1, 1936

By G. Morin, S. Amira, F. Chiesa, B. Duchesne

"The effect of heat treatment on the stress corrosion cracking (SCC) resistance of A206 aluminum alloy was studied using the breaking load test according to ASTM G139 standard. This method uses the residual strength measurement from tensile test specimens previously stressed axially while exposed to the 3.5% NaCl alternate immersion test according to ASTM G44 standard. The residual strength after exposure is used as a measure of SCC degradation. The performed heat treatments were conventional natural aging T4 and artificial over-aging T7 tempers in addition to artificial aging T6 temper added for purpose of comparison. These tests showed that A206-T4 has a good resistance to SCC at pre-loads up to 100 MPa while A206-T7 was prone to SCC for pre-loads of 0 and 50 MPa, and showed total loss of ductility for pre-load of 100 MPa. Both A206-T4 and A206-T7 pre-loaded at 150 MPa showed poor resistance to SCC. A206-T6 showed the worst susceptibility to SCC as it lost all mechanical resistance at the end of the alternate exposure to 3.5% NaCl solution, even without any applied pre-load. Metallographic analyses showed that the resistance of A206 alloy to SCC is mainly affected by the transition from pitting to intergranular corrosion attack. The initiation and the propagation of intergranular corrosion attack might be assisted by high stress concentrations in the pits, particularly for pre-loads higher than 100 MPa. The transition from pitting to intergranular corrosion can also be promoted by hydrogen evolution from growing pits, which supports crack propagation by hydrogen embrittlement.INTRODUCTIONA206 aluminum-copper casting alloy offers ones of the best mechanical properties among the aluminum foundry alloys. This alloy belongs to the 206 alloy family developed in 1970s as an alternative to the highly resistant and ductile but more expensive Ag containing 201 alloy (Tiryakioglu, 2009). A206 showed also good low cycle fatigue strength (Sigworth, 2002). These properties made A206 alloy a strong candidate for some vehicles lightweighting applications. In spite of its interesting properties cited above, A206 alloy was rarely used in critical applications due to its tendency for hot tearing and stress corrosion cracking (SCC). Studies of A206 hot tearing behavior showed that this tendency can be reduced by improving castability and by grain refinement (Sigworth, 2002). The optimisation of the casting design can also prevent the tendency toward hot tearing. The SCC of aluminum-copper alloys arises from their susceptibility to localised corrosion, especially in chloride containing media. The localised corrosion in Al-Cu alloys is caused mainly by their heterogeneous microstructure, where the presence of many phases leads to the formation of micro-galvanic coupling with the matrix. However, most of the studies aimed at investigate the SCC of Al-Cu alloys concerned the wrought ones, especially the AA2024 alloy tempered in the T3 (or derivative) condition and few studies concerned the 206 and cast alloys in general (Alexopoulos, 2009 and 2016; Campestrini, 2000; Vogt, 1998; Talamantes-Silva, 2008; Zhang, 2003). Jean et al. (Jean, 2009) studied the effect of heat treatment on SCC behavior of B206 alloy using alternate immersion technique and grain boundary attack method and did not find direct correlation between the two methods. Another study showed that aging of 206 alloy may make a casting susceptible to SCC (Sigworth, 2002). However, these studies did not provide detailed information about the mechanisms of SCC of 206 alloy, as well as the effect of the stress intensity. The present work investigates the effect heat treatments and the stress intensity on the morphology of the corrosion attack and the SCC behavior A206 aluminum alloy. This study uses the breaking load test according to ASTM G139. This test utilizes direct tensile specimens and was developed to give a more quantitative measure of the SCC performance of resistant aluminum"

Jan 1, 2016

By J. E. Moran

A groupd of French capitalists, La Compagnie Française des Mines d'Or du Canada, has undertaken the considerable task of developing Otter creek, in the Atlin district, B.C., by hydraulic mining methods. It has long been known that the gravels of this stream carry sufficiently high values in gold to make it attractive as a mining venture, but it was impossible to ignore the existence of formidable natural obstacles to hydraulicing them, and these needed to be taken into serious account before embarking upon any costly programme of development. The tide to the Otter Creek leases was originally held by Mr. H. Maluin, a French engineer well known throughout the north, to whom was to fall the task of financing whatever programme might be decided upon. It was he, too, who would have to assume the responsibility of finally passing judgment upon the practicability of the various devises for overcoming the adverse natural conditions. With an infinite attention to detail, which I believe to be a characteristic of the French people generally, he studied his problem and was finally able to submit to his financial backers a programme which left the very minimum possible to the hazard of accident or chance. Dr. Mandy, on his visit to Otter creek this season, expressed the opinion that our method of opening this difficult creek presented certain features which might be successfully applied in placer operations elsewhere in British Columbia, and it is largely for this reason that the present paper has been prepared. I shall set forth, as well as I can, the practices which have enabled us to overcome rather easily some of the obstacles which nature had unkindly placed in the path which we must take. The natural flow of water in Otter creek is far too little to deal success-fully with the rather excessive amount of glacial drift overburden which lies directly over the gold-bearing gravels. For this natural defect, the only remedy was to procure more water. This we have clone through a system of flumes and ditches, totalling between ten and eleven miles in length, which bring to the mine a supply of water adequate for our needs.

Jan 1, 1932

By Robert D. Brown

"All ten Canadian provinces have now tabled their 1981 /82 budgets . Only the provinces of Ontario, Quebec and British Columbia made more than minor modifications to their tax structures, with both Ontario and Quebec imposing major tax increases. In the past year, the federal budget was also released in the spring. Not so this year: we have that to look forward to in the fall!This month, Tax Notes presents a brief summary of the more significant tax changes introduced at the provinciallevels in the last months.Summary of provincial tax rate changesThe tax changes in this year's provincial budgets were both up and down- but there were far more tax increases than tax cuts.At the corporate tax level, two provinces, New Brunswick and British Columbia, increased their general corporate income tax rate; the former by two percentage points and the latter by one percentage point. Quebec, rather unexpectedly, sharply cut its corporate tax rate on business income, but increased some of its other business taxes at the same time. British Columbia reduced its corporate tax rate on small business income by two percentage points and Saskatchewan by one percentage point."

Jan 1, 1981

By I. M. Santos Moraes

The control of minor impurities (mainly As, Sb and Bi) in copper refineries has been a great challenge. Caraiba Metais' copper refinery produces a very high quality copper, registered in LME as grade A, and recognized as amongst the top ten in the copper world. At Caraiba's Tankhouse Bi and Sb are controlled by means of electrolyte bleed-stream removal after partial decopperizing in a set of electro-winning cells (liberators). Another way of reducing the Sb and Bi content in the electrolyte is by means of the arsenate precipitation chemistry. It is well known that the use of high arsenic concentrations in copper refinery electrolyte has the advantage of causing most of the bismuth and antimony to report in the anode slimes. However, the use of such mechanism of control may contribute to other undesired problems such as antimony and bismuth precipitation in the bulk of the electrolyte, what may cause severe contamination problems. This paper describes a period when some cathode contamination with Sb occurred at Caraiba Metais' Copper Refinery. It also presents an analysis of several process parameters related to the problem, the possible causes for the contaminations as well as the actions taken to correct the problem.

Jan 1, 2007

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007

By J. L. Casado-Sánchez

Financial capital is highly volatile and if the investor does not get adequate compensation for the risk faced he may consider withdrawing his capital assets from the company and consequently produce a structural change in any sector of the economy. We study the variation in profitability of assets in terms of the changes that occur in the markets. The choice of models used is justified by the extensive theoretical and empirical use of them throughout the history of financial economics. We have used the capital asset pricing model (CAPM) and the model based on the arbitrage pricing theory (APT) to determine the beta value. These models have been applied to the monthly returns of 27 mining companies listed on the New York Stock Exchange (NYSE) or London Stock Exchange (LSE), using data from the period covered from January 2006 to December 2010. The results of time series and cross sectional regressions for CAPM and APT produce some errors, suggesting that many companies have failed to obtain an adequate cost of capital. Also the results show that higher risk firms tend to have lower profitability. These findings make it unlikely to be maintained over the long term the current status and could drive structural change in the mining sector in the form of mergers.

Aug 1, 2013

By Mario A. Morin

Over the years, several sources have stressed the need to better integrate the underground mine design and planning processes. The belief is that with better integration, better designs and plans will result - designs that are ?optimized?. Some researchers have focused their efforts on data integration, others have looked at closing the loop between production control & monitoring with mine planning & scheduling. In spite of all these efforts, fully integrated applications combining geological modeling, stope design and geomechanics, mine planning and scheduling, rock extraction and material handling system design, mine support systems, economic analysis with production control do not yet exist for the underground hard rock mining industry. There are several likely explanations - some economic, some technical. It is certain that the design and planning processes are interrelated and interdependent and thus are extremely complex to describe and understand. The mining engineer has an appreciation of the complexities involved - but how does he convey this knowledge to a programming team responsible for developing an integrated design & planning system. This paper will focus on software engineering methods, and other possible approaches, to describe and manage the complexities inherent in the underground mine design and planning process and the development of an integrated computerized system.

May 1, 2001

By J. A. Meech

"The technology known as Expert Systems is being used within the minerals industry in a wide variety of problem areas. Applications include diagnosis, prediction, training, monitoring and control. Expert Systems provide a way to program computers to imitate human thinking. The construction of such systems is a straight-forward task that can be quickly learned by novices but can require a lifetime to master.To assist in the understanding and utility of this technology, a special manual bas been prepared which operates on a microcomputer under the MS-Windows environment. The manual covers all aspects of Artificial Intelligence of relevance to Expert Systems. A hypertext system allows users to probe as d•~ply as needed to achieve understanding or to simply skim the surface of the knowledge to obtain a quick overview of subjects. The manual was developed under the sponsorship of the Mineral Sciences Laboratory of CANMET and is available from the Mining and Mineral Process Engineering Department at the University of British Columbia. Annual updates are planned to keep abreast of new developments in this rapidly changing technology. RESUMELa technologie: des Systèmes Experts est utilisée par l'industrie minière pour résoudre une grande variété de problèmes. Les domaines d'application comprennent le diagnostic, la prédiction, la formation, la surveillance et le contrôle des procèdes. Les Systèmes Experts permettent d'écrire des programmes d'ordinateur qui imitent le processus de la pensée humaine. La construction de tels systèmes e:st une tâche qui peut être apprise rapidement mais qui peut prendre des années à maitriser.Pour aider à mieux comprendre et utiliser cette technologie, un manuel spécial opérant sur microordinateur dans l'environnement Windows a été développe. Le manuel couvre tous les aspects de l'intelligence artificielle qui concement les Systèmes Experts. Un système ""hypertexte"" permet à l'utilisateur d'étudier un sujet en profondeur ou de simplement couvrir une grande variété de sujet en surface. Le manuel a été développe avec l'aide financière du Laboratoire des Sciences Minérales de CANMET et est disponible au Département de Génie Minier et Minéralurgique de l'Université de la Colombie Britannique. Des mises à jour annuelles sont prévues de manière à couvrir les changements et nouveautés de cette technologie en évolution."

Jan 1, 1993

By M. Bertrand

Oxalic precipitation is usually applied to process radioactive wastes or to recover actinides from a multicomponent solution. Precipitation reactions being highly sensitive to many operation parameters, the computer simulation appears to be a very effective tool to forecast the evolutions of the system subjected to various operating conditions. This study focuses on the tetravalent uranium oxalate precipitation modelling which combines population balance and hydrodynamics. Both experimental and numerical studies are carried out in order to analyse the reactor design influence on the precipitate characteristics. The simulations taking into account primary nucleation and crystal growth are in agreement with experiments.

Aug 1, 2010

By S. Perkins, E. Young, L. Dufour, K. McVey, L. Rolandi

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By Michael K. Watkeys, Jacobus E. Potgieter, E. Guy Charlesworth, Carl R. Anhaeusser, Roger L. Gibson, Alexander F. M. Kisters

Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-erustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress [( )] during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diapir-like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994