Search Documents

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By C. O. Swanson

CALCULATING the average grade of a gold deposit is a problem that presents certain unique difficulties. Particularly troublesome is the fact that the average of the samples taken from a deposit is likely to be higher than the grade of the ore that is eventually mined, even when allowance is made for dilution and other factors resulting from the mining operations. It would seem that this situation is due to the presence in the deposits of structural peculiarities which have not been properly taken into account, since estimating the average grade of the broken ore produced from the deposits does not present the same difficulty. It is therefore evident that structural considerations are of prime importance in estimating the grade of a deposit. This fact is clearly realized and taken into account in cases where the boundaries of the orebodies and the variations within them are easily recognized. But in many gold deposits this condition is not satisfied, a circumstance which can be regarded as the main source of difficulty. Lacking definite information concerning the structure, we are apt to use certain procedures which are either empirical or based on general probabilities.

Jan 1, 1945

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

By H. Ito, T. Takasu

Effects of a mechnochemical treatment to oxide Ni ores have been investigated to enhance the extractive ratio of Ni from them in acid leaching process. High intensity grinding by a planetary boll mill showed strong effect to enhance the extractive ratio of Ni, for example , 10% of extractive ratio of Ni in sulfuric acid leaching(0.05mo1/1,at room temperature) increased to more than 90% with 60min. of planetary boll milling. Effects of additives(sulfur and some oxidants) on the mechnochemical treatment have also studied. Sulfur showed almost no effect to enhance the total Ni extractive ratio but increases the selectivity of Ni extraction. More than a half of Ni could be extracted by water when Ni ore was grinded at addition of Na2S207 in the milling treatment. Some effects of mechnocemical treatments to Ni ore are summarized in this paper.

Jan 1, 2005

By Shahé Shnorhokian

A study was conducted on the seismic activities and associated rockburst events that took place at an underground Canadian metal mine over a period of five years. In the first stage, a back analysis of the microseismic database led to the identification of clusters of major events. The locations of these clusters were identified with respect to the local geology and the planned mining sequence. In the second stage, a numerical model was constructed using the finite difference code FLAC3D to simulate the in-situ stress, mine geometry, local geology, and stope sequence. Mining-induced stress fields were compared against two rockburst events that took place during this period, as well as against the various geologic units present. It was shown that by combining microseismic analysis and numerical modeling, it was possible to provide a basis for evaluating the influence of the in-situ stress regimes and stope sequencing on mining-induced seismic response.

May 1, 2011

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By W. Leblanc, J. Phalen

This paper tells the story of a serious mine fire on a mechanized longwall face in a submarine coal mine at Glace Bay, Nova Scotia. The story gives, in chronological order, a technical account of the steps taken to investigate, fight and contain the fire. The time during which the events took place spans from June 19 to November 7, 1975.

Jan 1, 1976

By Pavel Vasak

The Laurentian University Virtual Reality Laboratory (VRL) has provided a unique platform for the development and testing of novel seismic and microseismic data processing and visualization technology. In collaboration with Vale?s Creighton Mine, the technology was implemented at the mine site and consists of a VRL system and site calibrated Seismic Excavation Hazard Map (SEHM) software. The SEHM was developed as a practical solution for the mine operator to identify areas of elevated, active rock mass damage processes caused by recent mining activity. This paper is a pictorial representation of the 3D stereoscopic demonstration of the Creighton Mine seismic data distribution and interpreted SEHM for the first quarter of 2009. A live demonstration is scheduled at the Laurentian University VRL as one of the conference field trips. The demonstration highlights the technology transfer of research concepts into a near-real-time excavation hazard system that utilizes the key aspects of virtual reality technology; the ability to integrate large datasets (geology, mine excavation, (seismic) monitoring data, production scheduling, stress model, etc.); the ability to manipulate and visualize large datasets in both space and in time (mining sequence); and the ability to review the datasets by a group of experts in an immersive (3D stereoscopic), collaborative environment to better understand the processes and context of the mining-induced seismicity and evaluate potential risks to the mining operation.

Oct 1, 2010

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick's Law in 1947, through to today's models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005

By Fred Delabbio

There are presently several issues that the mining industry is facing, such as underground air quality, deep mining and green house gas emissions, which could be addressed by the application of alternate energies. Several aspects must be considered by the industry in any drive to introduce new technologies within the context of a producing underground mine. This article presents several operational and support aspects that will evaluate the relevance of alternate energies, with emphasis on hydrogen power systems: operational drivers, commercial supply of technology, site supply system requirements, health and safety, capital and operating costs, mine production, corporate philosophy, and role of government. It is concluded that introduction of alternate energy technology requires a step-wise progression: Applicability to the industry, proof of concept testing, development of generic infrastructure, power systems and regulations, whole system studies and detailed studies of cost and risk versus benefits. The current initiative to apply fuel cells is at the proof of concept stage, entering the generic infrastructure stage.

May 1, 2007

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999