Search Documents

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By Ashutosh Shandilya

Froth flotation is a selective separation process and rarely used for beneficiation of limestone in the world as compared to other minerals and also mostly known conventional methods of up gradation of ROM including wobbling, selective mining, sorting, preblending etc. Limestone is mainly used in the manufacture of cement, steel and chemical industries. High grade limestone deposits are depleting day by day and the requirement of the industries have to be met by beneficiating the low grade limestone deposits in the world. And because of marginal quality of limestone, it cannot be directly used in cement industry. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full fledged mineral beneficiation process is adopted to enhance the quality of low grade lime stone from 38-42 % CaO to 45-47 % CaO and silica reduced from 19-22 % to 11-13 % by use of oleic acid (commercial grade and vegetable origin) 0.38 kg/ton of limestone and caustic soda 0.05 kg/ton of limestone. Keywords: OK-8 Cells, Froth flotation process, Beneficiation studies, Low-grade lime stone, Oleic acid, % solids, Pulp density, Ph, Iodine value, saponification value, Denver cell

Sep 1, 2012

By G. Atesok

Turkey?s EU affairs started in 1963 with the Ankara Treaty. On 31 December 1995 the Customs Union between Turkey and the European Union came into effect. In order to achieve the Copenhagen Criteria?s, Turkey, made laws parallel to the Framework Programs. On 3 October 2005, with the confirmation of ?Membership Framework Document? the negotiation process of Turkey has started. Coal had important role in the industrialization of EU and it is directly related to Energy and Environmental subjects. In this point many restriction became with the some protocols, in last decades. European Union composed Energy and Coal Policy, therefore engaged to reduce the emissions, and made new regulations. This regulations concern Turkey?s energy future, since large; but low quality of lignite reserves of Turkey, it is expected to have some difficulties with Union?s Environmental Legislation during Turkey?s congruity process. With the last natural gas import agreements of Turkey, the production and consumption of coal sunk in last seven years. However, considering environmental sustainability, the role of coal in energy production will rise up in the coming future. In this paper, in terms of Turkey Energy Sector, production and consumption problems of coal discussed and evaluated considering EU?s coal, energy and environmental rudiments.

Jan 1, 2014

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

Anglo American Platinum practices fine grinding in its processing plants to enhance the liberation of valuable minerals. If the fine particles of valuable minerals generated during fine grinding are not recovered during the flotation process, this could significantly contribute to the overall losses. This study examines the flotability of fine moncheite (PGE mineral) particles in a controlled environment (moncheite size distribution, concentration and liberation). A barren Norite ore ground to 40% and 80% passing 53µm was spiked, with four different size fractions of moncheite (-5, -10+5, -25+10 and -53+25µm) in order to evaluate the effect of particle size on flotation. The investigation also included the effect of energy input and collector dosage on the flotation of two moncheite size fractions, namely -5µm and -10+5µm. The results showed that the moncheite particle size has a significant impact on flotation. Coarse particles (-53+25µm) showed the highest Pt flotation kinetics and overall recoveries. The -5µm size fraction of moncheite could also be recovered by flotation, however, at a lower rate compared to the other size classes investigated. The increased collector dosage of 300g/t at the finer Norite grind of 80% passing 53µm enhanced the flotation rate of the -5µm size fraction of moncheite when compared to the lower collector dosage of 150g/t. The higher energy input during laboratory flotation, at an impeller speed of 1000rpm also increased the flotation rate of the -5µm size range, however, at a lower concentrate grade, when compared to the lower impeller speed of 700rpm. More favourable Pt flotation kinetics data was obtained for the -53 +25µm size fraction of moncheite at the fine Norite grind when compared to the coarse Norite grind. Keywords: flotation, moncheite, particle size, energy input and SIBX

Sep 1, 2012

By V. A. Chanturiya

The application of High-Power Nanosecond Electromagnetic Pulses (HPEMP) irradiation in dressing of resistant gold- containing ores appears attractive as this technique provides for a significant increase in precious metal recovery (30-80% for gold and 20-50% for silver), therewith helping reduce both energy consumption and the cost of products. The prospects for applying pulsed power technologies in the mineral processing in order to increase the contrast between the flotation properties of raw minerals dictate the need to perform special studies of the effect of HPEMP on the structural state, phase composition, and physical and chemical properties of surfaces of sulfide minerals as the main carriers of precious metals. This study deals with plausible mechanisms of the micro- and nanophases formation on the surfaces of sulfide minerals under the effect of high-power nanosecond electromagnetic pulses (HPEMP) with high electric field strength ~107 V/m. This paper discusses reasons for the changing of flotation behavior of natural pyrite and arsenopyrite during the pulsed-power treatment. It was concluded that HPEMP treatment may be regarded as a tool to change the surface composition and sorption ability of collector (xanthate) onto mineral surface, and, therefore, it allows to control the hydrophobic-hydrophilic surface balance. Single mineral flotation tests have been shown the significant increasing of the pyrite recovery while the arsenopyrite was depressed. The results of gold containing pyrite (pyrrhotite)-arsenopyrite ore flotation in batch approve the decreasing of arsenic recovery in sulfide concentrate. Keywords: pyrite, arsenopyrite, high power nanosecond pulses, activation, selective flotation

Sep 1, 2012

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By Skinner. W.

"Introducing cutting-edge development work, which aims to simplify mineral processing flow-sheets, reduce costs and address environmental issues. Over the past four years Innovative Mineral Processing Technologies Pty. Ltd (IMPTEC) Australia have developed a Super-fine Crusher and a Planar Magnetic Separator which offer low cost, wet or dry alternatives to conventional grinding and conventional magnetic separation. Each of these machines has been successfully trialed at pilot scale and are now in the process of transitioning to commercial scale. This paper reports on the progress made in each of these fields. The potential scope for application of super-fine crushing technology as an alternative to grinding is potentially expansive and could include beneficiation of metalliferous ores, precious metal ore processing, hydrometallurgical processing, industrial minerals and coal processing, plastic fillers and ceramics processing as well as processing of cementitious slags and fly-ash. IMPTEC have recently achieved outstanding results at pilot scale with a dry combination of super-fine crushing and planar magnetic separation, which offers an alternative to the wet processing of magnetic iron ores. The dry combination has set new laboratory performance benchmarks when compared with the industry standard wet Davis Tube Tester. The test results have also established a strong evidence base showing that super-fine crushing achieves liberation of value minerals at coarser sizes when compared with grinding. The dry combination of super-fine crushing and planar magnetic separation also addresses environmental issues and completely eliminates grinding. An IMPTEC super-fine crusher is currently undergoing commercial trials, generating ultra-fine products from granulated lead blast furnace slag for use as cement substitutes. The performance of the super-fine crusher on this extreme duty highlights the potential benefits of super-fine crushing over the wide range of industries and applications where conventional grinding is employed.INTRODUCTION Present day mineral processing practices can become anchored in convention, where, inefficient methodologies are recognized and accepted as “best practice” or “industry standard”. Motivated by this challenge, IMPTEC has undertaken the development of radically different and improved methodologies in the fields of fine comminution and magnetic separation. Whilst, crushing is much less energy intensive and generally less capital and maintenance intensive than grinding, the technology has stalled due to the lack of crushing devices, which have the capacity to adapt to fine and ultra-fine duties. Grinding practice advances have been achieved through major increases in machine size and power. However, these advances are also accompanied by major escalations in capital, operating and maintenance costs. The economics of this strategy has become increasingly questionable. A typical example is the viability of low-grade magnetite beneficiation, which can hinge largely on the cost of grinding to fine and ultra-fine liberation sizes."

Jan 1, 2018

By Y. F. Li

Fengning ilmenite ore is a magnetic deposit in gabbro containing high phosphorus and low titanium, the main minerals in which are ilmenite, magnetite and apatite. The dissemination size of magnetite is so fine that even the percentage of -0.010mm level is up to 36.50%. The fine and vein magnetite are distributed in gangue and ilmenite, so the majority of the magnetite is difficult to be separated from the gangue. Ilmenite is difficult to be recovered by low-intensity magnetic separation even through fine grinding. In high-intensity magnetic separation of ilmenite, the gangue inter-growth with the magnetite and the Fe-containing silicates may be enriched in the concentrate, and the ilmenite of the concentrate will be reduced. Based on the processing mineralogy research, combined gravity-flotation process is suggested to recover the ilmenite. The method is also good to reduce phosphorus in the ilmenite concentrate.

Jan 1, 2014

By C. B. Yu

The ore comprise of chalcopyrite, valleriite, pyrite, pyrrhotite and so on. Serpentine and talc are chief gangues. Copper phase of the tail shows that mostly valleriite be losed in tail, 70% mineral of copper is valleriite in tail, so severity reduce the recovery of copper. The traditional flow-sheet in acidity mine pulp to flotat the valleriite, but copper-sulphur separated in high alkaline pulp, so the valleriite be losed else. Explores the characters of the valleriite?s surface, studys on the flow-sheet of flotat valleriite and copper-sulphur separated. In neutral mine pulp, adopt of cationic collector to flotat valleriite, adopt of hyposulphite to depressant pyrite in low alkaline pulp can advance the recovery of copper to 5.06%.

Jan 1, 2014

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By Jacqueline Satur, Yoshiaki Kon, Buenaventurada Calabia, Xiao Sheng Yang, Arvo Naumanen, Kenzo Sanematsu, Sayaka Morita, Tetsuichi Takagi

Granite ores are composed of silicate minerals and a variety of valuable REE (rare earth elements)-bearing minerals, however the processing technique to recover these valuable minerals is not yet developed. In this study, the recovery of REE-bearing minerals by dry magnetic separation and wet high intensity magnetic separation (WHIMS)-settling from surface sample and from drill core sample, respectively, of a granitic REE-Zr-Nb ore deposit was investigated. The two samples have different mineralogy however in both samples, light REE are commonly contained in REE carbonate minerals while Y and heavy REE are commonly contained in zirconium silicate minerals and pyrochlore. The liberation size of the REE-bearing minerals in the two samples ranges from 10-250 ?m. Previous flotation testwork conducted on the drill core sample reported high recoveries of La2O3 (88%) and Ce2O3 (88%) but low recoveries of Y2O3 (42%), ZrO2 (17%), and Nb2O5 (29%). The objective of this study was to obtain higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling. Both processes implemented the application of a low magnetic intensity to initially separate the ferromagnetic minerals then a high magnetic intensity to recover the REE-bearing minerals. The results showed higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling indicating the potential of magnetic separation and gravity separation in recovering the heavy REE-bearing minerals. WHIMS-settling is more recommendable than dry magnetic separation because of its applicability in treating a wider range of particle size. In the WHIMS-settling, the light REE, Y, and Zr minerals were recovered mainly by applying four stages at high magnetic intensity of 21,500 gauss while the weakly magnetic pyrochlore was recovered mainly by decantation of the nonmagnetic slurry after a short settling time of 0.25 to 0.50 h. (MAX.300 words)

Jan 1, 2014

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014