Search Documents

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By G. Hames, A. Drake, B. Sampson

The Timbarra opencut gold mine is located about 30 km(19 miles) southeast of Tenterfield in northern NSW some 4 hours by car from Brisbane, the capital city of Queensland in Australia. It was a small operation designed to produce about 40000 ounces of gold per annum utilising contract mining and company owned crushing plant feeding heap leach pads. This is a standard setup except that the mine owner was in charge of all aspects of drill & blast design even though a contract drilling & blasting (shotfiring) service was being provided. The major problem was that the blasting operations were yielding massive amounts of oversize due to the jointed partially weathered nature of the granite. This was adversely affecting all downstream aspects of the operation as well reducing gold output as ore boulders were being dozed over the side of the mine as they were impinging on mining productivity. The oversize problem had to be solved as the mine was struggling to achieve design gold output. Significant design & trialing effort using minesite resources were utilised to reduce the oversize but this failed even when powder factors up to 1kg/bcm(1.68lb/yd) were used. Dyno Consult from Dyno Nobel were therefore called to investigate, review & trial options to reduce oversize from the top flitch.

Jan 1, 2003

By W G. Szymczak, Leslie C. Taylor

The University of Maryland (UMD) has conducted a series of small-scale tests using explosive charges buried in saturated sand. Twelve different combinations of depth of burial of the charge and height of the target plate above the soil were tested. The target plates did not deform plastically. High-speed video was used to track the motion of the plate. The video data are analyzed to determine the position and velocity of the plate as a function of time. The results of this analysis are compared with computations performed at NRL using the BUB2D computer code. This code treats the saturated sand as an incompressible visco-plastic fluid which yields according to a Drucker-Prager (frictional-cohesive) yield surface. Comparisons of simulations with experiments are presented. In the cases examined so far, the velocity grows very quickly to a peak and then slows, first with a deceleration greater than one “g,” which then transitions to an approximately one “g” deceleration. An analysis of air drag on the plates has shown that its effect is negligible in the time span of interest. In all cases in which the BUB2D code can be applied, the computations compare favorably with the results of the data analysis. This suggests that the code and model used in the computation are properly capturing the physics of the interaction between the soil and a non-deforming plate.

Jan 1, 2007

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By Rob Farnfield, William Birch, Douglas A. Anderson

In the blasting industry, even to the most safety conscious shotfirer, misfires are a constant source of concern. In the United Kingdom, there are two types of misfire, as classified by the Health & Safety Executive. Type A occurs when testing a shot before firing reveals broken continuity that cannot be rectified. However, due to the fact that a majority of quarries use non-electric initiation [i.e. shock tube] that cannot be tested, this type of misfire is very unusual.

Jan 1, 2016

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By Tapan Goswami

The expectation from the blasting engineers and shotfirers is often that explosives will perform optimally at all times. However, in reality, non-ideal situations exist on mine sites and occurrences of poor explosives performance are common. Often the cause is difficult to identify. Having a good application technique and analysis skills will minimise the risk of poor performance. This paper will discuss the experiences gained by the author while blasting in the Hunter Valley, Australia.

Jan 1, 2003

By Jun Yang, Zongshan Zou, Mei Qu, Jianjun Zuo

For technical renovation of the thermal plant, one frame structure workshop of 50,000 m2 (59,800 yd2) construction area and one reinforcement concrete chimney of 150m (492 ft) height shall be demolished by blasting at same time. The engineering environment of which is complicated and the accommodation space is limited. Therefore, the collapse sequence, direction, scope of the dismantled building must be accurately controlled to ensure the safe operation of the adjacent generator unit and transformer station. By taking technical measures of theoretical analysis and numerical simulation etc., as well as research on structures collapse method and detailed delay interval, it puts forward the technology of bidirectional folded collapse of the workshop and it uniquely adopts the initiation system that combined with “half-second delay inside drilling” and “millisecond delay outside drilling”. Additionally, by using of the integrated vibration reduction technology in combination of the blasting ruins, buffer ditch and damping ditch, it has safely accomplished the demolition blasting work in high efficiency. Besides the demolition blasting vibration signal is collected and analyzed. The success of the demolition blasting will become valuable reference to other similar works.

Jan 1, 2016

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Dale Bartholomae, David Harrison, Edward J. Walter

Methods that involve the use of signature blast holes in order to identify the particular frequency characteristics of a geographical area are widely available. Information acquired can be used to determine optimum blast hole timings to produce the desired constructive and destructive inference. However, these types of analyses can be both complicated and expensive. This study will investigate the use and practicality of signature hole and/or shift and sum analysis software and their application to small diameter construction utility blasting operations in Pennsylvania and faster moving projects in general. A determination will then be made as to whether this technology can be utilized by today’s blaster, from both a functional and a cost effective basis. Single hole blasts will be detonated on various smaller construction projects and will be monitored with an array of seismographs. The collected data will be analyzed in order to determine the optimum timing between holes to produce the preferred frequency content while keeping in mind the explosives user’s current inventory of blasting supplies.

Jan 1, 2005

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By William C. B. Gates

Demolition blasting next to an active railroad can be very challenging because of track safety, blasting vibrations, potential track fouling by blast debris, and short work windows on a live track. Recently, in eastern Washington, one of the major railroad companies has been aggressively constructing a second main track to accommodate the expected increase in rail traffic of natural resource products. To accommodate construction of the second line, the railroad company used blasting demolition techniques to remove an old railroad trestle pier on the Milwaukee Road that was in the footprint of the new track bed. The trestle bridged the present rail line and flanked the track with two massive 550-ton (499 tonne) twin-columned steel reinforced concrete piers. The railroad contracted with a specialized contractor to remove the south pier using blasting demolition techniques. The blasting design presented the following challenges: blasting during live track conditions and short work windows; designing a V-notch blast pattern to ensure the pier fell away from the live track; drilling, loading, and timing of the shot; maintaining blasting vibrations at the track below 4 in./sec (102 mm/sec); maintaining ambient overpressure noise below 133 dB; control of fly rock and debris; and track protection and emergency debris removal plan.

Jan 1, 2016

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005