Search Documents

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

By Zuhair Ibrahim, Dan Tillema, Ali Reza

This paper details the investigation of a fatal explosion that occurred on April 8, 2011 at a magazine used to store fireworks in Waikele, HI. The fireworks had been confiscated by the Bureau of Immigrations and Customs Enforcement after they were informed that a container shipped to the United States contained illegal fireworks. Four groups of cardboard cartons that were marked as 1.4G (consumer fireworks) were determined to be consistent with the more explosive 1.3G type, commercial display fireworks. The subcontractor retained to destroy these fireworks stored the shipment in the subject magazine and was in the process of disassembling them on the day the explosion occurred.

Jan 1, 2014

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By FM Murray

SAFEX International is a global organisation with more than 85 members, all of whom are manufacturers of explosives. On joining each member signs a declaration saying that they are willing to exchange information with regard to any accidents or near misses they may have in order to prevent the recurrence of the incident. SAFEX International was formed 50 years ago in Europe and has now built up a database of more than 700 accidents in the explosives business. Once every three years, an International Congress is held in which members address specific safety themes associated with the explosives industry, and also give details of "what went wrong?", "why?", and lessons learned. The next Congress will be held in Amsterdam between the 29th May and the 1st June 2002. This paper describes the operation of SAFEX International, which is dedicated to the international exchange of experience on industry connected accidents of the explosives business.

Jan 1, 2002

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By Elaine Gorham-Bergeron

CAROM is a distinct element, dynamic code developed at Sandia National Laboratories to calculate the motion of rock fragments during blasting.[1] It has recently been improved to incorporate a mechanism for its elements to mimic non-circular rock fragments. With this option, elements stack and move in ways that are characteristic of irregular boulders of blasted rock. In bench geometry, CAROM has been used to examine the possibility of producing variations in muckpile shape due to variations in detonation-time delays between rows. Surprisingly, the shape of the muckpile was predicted to be insensitive to time delays between detonation of rows of explosive, except where the rock fracturing was affected by the time delays.

Jan 1, 1987

By Gregory P. Lorsbach

Significant information about any blast is contained within the seismic signal generated by the blast. In this study, standard digital signal processing techniques are utilized to extract source parameter information from a seismic signal recorded at distances commonly used in compliance monitoring. Specifically, digital seismic data was analyzed using the cross-correladon and autocorrelation functions for the purpose of determining delay timing. The initial results are interpreted to indicate that: 1) Individual delays can be identified analytically but not visually for short delay periods and large source to receiver distances, 2) Delay timing can be resolved to a few milliseconds, and 3) Results can be obtained from data collected at a minimal number of locations.

Jan 1, 1991

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By Mark S. Stagg, David E. Siskind

The Bureau of Mines arranged to have a wood-frame test house built in the pat of an advancing surface coal nine so it could investigate the effects of repeated blasting on a residential house. Structural fatigue and damage were assessed over a 2-yr period. The house was subjected to vibrations from 587 production blasts with particle velocities that varied from 0.10 to 6.94 in/s. Later, the entire house was mechanically shaken to produce fatigue cracking. Failure strain characteristics of construction materials were evaluated as a basis for comparing strains induced by blasting and shaker loading to those induced by weather and household activities. Cosmetic or hairline cracks 0.01 to 0.10 mm wide occurred during construction of the house and also during periods when no blasts were detonated. The formation of cosmetic cracks increased from 0.3 to 1.0 cracks per week when ground motions exceeded 1.0 in/s. Human activity and changes in temperature and humidity caused strains in walls that were equivalent to those produced by ground motions up to 1.2 in/s. When the entire structure was mechanically shaken, the first wallboard tape joint crack appeared after 56,000 cycles, the equivalent of 28 yr of shaking by blast-generated ground motions of 0.5 in/s twice a day.

Jan 1, 1985

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Chuck Kliche, Bill Clements

This paper relates some of the experiences, good and bad, of blasting adjacent to residences of the primary author during his 15+ years of field blasting in the Northern Great Plains region. During this highly-rewarding blasting career, the author has become aware of two major issues in residential blasting: 1) What we call “Risk/Reward Ratio.”Some questions that must be asked by the blaster prior to taking on any blasting job include: - Can we eliminate or minimize the risk? - Is the reward worth the risk? - Do I have a measure of “nervous confidence” about the shot? 2) Public Relations. Two key elements to public relations are: - Notification - Education All the education in the world to the adjacent populous of what’s happening, of blasting in general, or of what to expect from the blasting does little good without notification. Good public relations is a key to controlling the cost of liability in a litigious society.

Jan 1, 2009

By Paul Worsey, Seokbin Lim

In many high explosive applications, the explosives are covered or clad by a metal. This metal cover may serve a variety of purposes including: 1) to protect and prevent the disturbing or misshaping of the explosive during its transportation, handling and use, 2) in many military applications the cover material itself is used to provide a required effect, for example, the shrapnel from grenades, the metallic liner of shaped charges, and the confinement of explosives so they perform optimally, and, 3) in civilian applications in the use of well perforating shaped charges and linear shaped charges used for the demolition of steel structures such as bridges. For these reasons the interactions between the explosives and their covering materials are of great importance in understanding the performance of these devices.

Jan 1, 2005

By Jerry R. Wallace

Infrastructure improvements and industrial plant expansion and modernization often require rock blasting within 20 feet of existing structures. In many instances trenchlines must cross beneath existing in-serv1ce utility lines.

Jan 1, 1994

By Michael D. McGill, John L. Turner, Don Sieger, Doyle Newhouse

Since its introduction by Atlas Powder Company in late 1986 as a means of highwall stabilization in surface coal mines (1), applications of the basic AirDek (2) blasting technique have multiplied rapidly.

Jan 1, 1991

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By H Russell

An account of an experimental blast at the Sullivan Mine involving a small pillar drilled with 4 1/2" diameter up-holes, and loaded with emulsion explosives from a truck-mounted tank/pump unit.

Jan 1, 1984

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997