Search Documents

By Charles H. Dowding

This paper describes NUVIB, analytical software to digitize, analyze, display, and plot time histories generated by blasting and construction vibrations. It is available in conjunction with a new book on Construction Vibrations (Dowding, 1996) through internet procedures described at the end of the chapter on analytical software These internet based procedures eliminate the need for inclusion of disks in the book and take advantage of the growing electronic communications network. Perhaps more importantly this procedure allows the software to be updated more often than the book is reprinted.

Jan 1, 1997

By Edward J. Walter

Vibration control is affected by many factors which are difficult to isolate and evaluate. Occasionally a circumstance occurs in which one factor appears to predominate and its effects can be evaluated. Changing rock characteristic or lithologic variation is one of these factors or parameters. In a recent seismic monitoring project, lithologic variation in the form of hard lenses occurring suddenly and randomly in the rock to be excavated caused sudden and large increases in vibration level. Data are presented to illustrate these effects, and procedures used to control these effects are described.

Jan 1, 1981

By Rene A. "Moose" Morin, Craig Copping

Innovative concepts in drilling and blast design have been used to remove deteriorated concrete and have enabled contractors to reduce costs and time on St. Lawrence Seaway rehabilitation projects. Time is of the essence on these contracts since the Seaway system is only available for this work during the winter freeze up. Unique electrical sequential initiation systems and specially modified drilling equipment have been used to accurately remove a narrow slice from the 83 foot high lock walls. These new methods successfully reduced demolition time, minimized overbreak and adhered to strict vibration limits.

Jan 1, 1986

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003

By B. M. P. Pingua & Md. Nabiullah

About 60 to 70 percent of bulk explosives are used in Indian coalmines to achieve coal production for power generation. Coal India Limited (CIL) is the major coal producing company in India. The average production of CIL is 400 to 450 million tonne coal per annum. The major subsidiaries of CIL are Northern Coalfields Ltd., Mahanadi Coalfields Ltd., Bharat Coking Coal Ltd., Eastern Coalfields Ltd, South Eastern Coalfields Ltd. and Western Coalfields Ltd. Most of the mines of CIL have watery holes. Therefore, high water resistance bulk explosives are preferred for better out puts.

Jan 1, 2008

By Calvin J. Konya

When blasts are designed, we normally assume the best case situation. We assume that all burdens and spacings will be properly drilled, holes will be properly loaded, initiators will fire at the nominal time and the explosives will release their full energy. This type of precision can be obtained at a machine shop where precision equipment is available to do machining, however, in the field, no matter how well a blast is designed on paper, it most likely will not be done in the exact manner in the field.

Jan 1, 1990

By Shulin Nie, Mats Olsson

The mechanism of rock fracture by explosive is a fundamental in rock blasting. It is generally believed that the shock waves from the detonation initiate the fractures. Then the detonation gases penetrate into the fractures and elongate them. However, our previous researches indicated that the detonation gases do not contribute significantly to the fracture propagation. In our latest experiment, blasts have been carried out in 8 large granite blocks. The main goal was to study the fracture mechanism, namely to determine whether the shock waves or the detonation gases fracture the rock.

Jan 1, 2001

By John A. Franklin, Norbert B. Maerz, D Linn Coursen

Accurate measurement of blast fragmentation is important in mining and quarrying operations, to monitor blasting and optimize blast design. A new digital photoanalytical method to measure the block size is presented here. Photographs of the broken rock are digitized, apparent size distributions measured, and corrections made for overlapping blocks, by means of an empirically derived correction function. The method was tested during recent full-scale blasting tests in Virginia, USA. It shows great potential as a practical aid to predicting, monitoring, and controlling the quality of the fragmented rock.

Jan 1, 1987

By Frank Lucca

This study is based on a six month study performed for Lee County, Florida. The study was based on blasting for land development and how this type of blasting affects structures. The study is investigates peak particle velocities and the relationship to other environmental and manmade forces that affect structures. The study also explores the effect of geology on blast vibration. After completion in Lee County, the study was then continued in the quarry environment in Vermont and extremely tight blasting environment of New York City. Charge diameters were 127mm (5 inches) or less.

Jan 1, 2006

By R. J. Cefalo

Blast and mining spillover between phases or critical areas of the pit is a continuing problem in the mining industry and a safety concern for operating mines. The challenge for many mines is to produce the highest value in the shortest amount of time for any project. For any project, the top priority of any mine is producing ore as fast as possible. The next challenge is to keep that ore feed continuous. To achieve continuous ore feed, pits are designed with multiple phases that are connected and are mined at different elevations. This difference in elevation causes dangers with spillover between the phases during mining, drilling, and blasting. This paper covers an incident that occurred at an active mine and the work completed in creating a spillover control program over an active mining phase. The drill and blast technical group was responsible for creating blast patterns to reduce spillover between these phases. Unrealistic goals and expectations were initially set for the area of the pit. The drill and blast technical group needed to figure blast objectives and work with the geotechnical team to align with these goals. This paper will go over the executed example of setting up spillover targets and expectations for multiple sections of an operating mine. Different sections of the pit had different control measures and blast objectives due to narrow laybacks and double benching. The use and value of blast objectives and goals were beneficial in setting expectations and measuring design success. Having unrealistic blast goals can set up the operations to fail or get frustrated in trying to work on an impossible task. The problems and risks of phase interactions for many open pit operations need to be considered in the design process, along with designed controls that minimize the probability of any safety incident. Mine designs are being created in the industry and do not consider phase-to-phase mining interaction and the impact it would have on safety or production. The best future for safer mines is blast patterns that reduce spillover between phases of mining and pit designs that might account for spillover interaction.

Jan 1, 2024

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By A. K. Sirveiya

A major concern with blasting at surface mines is generation of ground vibration, air blast, flyrock, dust & fume and their impact on nearby structures and environment. A study was conducted at a coal mine in India which produces 10 million tonne of coal and 27 million cubic meter of overburden per annum. Draglines and shovels with dumpers carry out the removal of overburden. Detonation of 100 tonnes of explosives in a blasting round is a common practice of the mine. These large sized blasts often led to complaints from the nearby inhabitants regarding ground vibrations and their affects on their houses.

Jan 1, 2005

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Baron Fidler, Dave Lilly, Matt Budin

Cumulative sum (CUSUM) statistical process control methods have been used in many industries to monitor quality control results. CUSUM charts are a method to determine when small changes in data indicate a major change in results. E.S. Page at AT&T developed the method in 1954. In many blasting situations, vibration and air blast readings vary slightly from blast to blast. Whether the change is significant or not can be hard to interpret from the raw data. CUSUM charts can assist in determining whether a major change is taking place and when the change began.

Jan 1, 2009

By Dale Ramsey

Located in the Chestnut Ridge Mountains of Southwestern Pennsylvania, the Casparis mine named for the founder Kenneth Casparis operated from 1916 until the early 1950. producing crushed stone for construction and railroad ballast. The rock was transported by aerial buckets to a railroad tipple nearly 1000’ (304.80 meters) below the mine. The mine property is now owned by the Pennsylvania Game Commission and is located in the Loyalhanna limestone seam with 4 primary entries that are approximately 40’ (12.19 meters) high by 30’ (9.14 meters) wide and extend over 2 miles (3.22 kilometers) into the mountain.

Jan 1, 2006

By Mike Wheat, Catherine Aimone-Martin, Brandon Pease

The Kneeling Nun rock pinnacle is a prominent landmark, 90 ft in height and 35 ft in width, that resides on a bluff overlooking the Santa Rita pit at the Chino Mines Co. operations near Silver City, New Mexico. The company plans to expand the current pit limits, resulting in a change in direction and distance of hard rock mine blasting operations in relation to the pinnacle. Concerns about the stability of the pinnacle adjacent to mining activity has prompted company personnel to enhance the seismic monitoring program both on the pinnacle and along the current open pit highwall that forms the base support below the pinnacle foundation. This paper presents the vibration response characteristics of the pinnacle, in terms of amplitude and natural frequencies of motions and damping characteristics, for measurements recorded at the top and base of the pinnacle. The influence that blasthole initiation timing and sequence of hole detonations have on vibration response is discussed. A simple analysis is made to estimate factors of safety against cracking of the landmark as well as blast-induced slope instabilities within the foundation rock.

Jan 1, 2000