Search Documents

By Roger L. McCarthy, Ali Reza

The use of an ammonium nitrate-fuel oil (ANFO) explosive in the Oklahoma City Federal Building bombing has led to a renewed interest in using additives during the manufacturing process of ammonium nitrate to render it non-detonable. Suggested additives include calcium carbonate, which is already used in some European countries, and mono-ammonium phosphate (MAP) or di-ammonium phosphate (DAP), which are the primary desensitizing agents claimed in US patent 3,366,468, Method for desensitizing fertilizer grade ammonium nitrate and the product obtained, issued Jan. 30, 1968 (Porter, 1965).

Jan 1, 1999

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By Jesus A. Pascual de Blas

After 30 years of development and introduction, electronic initiation systems are now well established in blasting applications, both mining, quarrying and civil works. In terms of blast technology, it could be considered that timing is the new challenge: how to define the most appropriate sequence to improve fragmentation, reduce vibrations, avoid dilution, eliminate damage… Some classic tools have been updated and adapted to the new scenario, and are giving us good performance; on the other hand, others should be considered obsolete, given the accuracy of electronic initiation systems has exposed these tools to incoherent conclusions. Besides, other tools have appeared and are in use, providing new approaches to old issues. Additionally, not only the technical side has to be considered: safety, security, economics are well present in daily blasting activity and affect to the final decision: are electronic initiation systems the right answer to my blast?

Jan 1, 2019

By Andrea Brickey, Ethan Marcoux

The South Dakota School of Mines and Technology (SD Mines), located in Rapid City, South Dakota, is one of only a few universities in the United States that offer a Bachelor of Science in Mining Engineering. The Department of Mining Engineering and Management (MEM) at SD Mines teaches courses that introduce students to concepts related to mining, including a course covering explosives engineering. Students are taught the basics of explosives theory and application in the mining and construction industry through a series of lectures and assignments. With limited field experience, many students find some topics difficult; these include: flyrock, ground vibration, timing, and others. Some US mining schools have an experimental mine in which they can simulate field conditions and conduct hands-on training, but not all universities have such facilities. For those without, teaching certain concepts can be more challenging in a pure classroom environment. To counteract the lack of an experimental mine, the mining department at SD Mines implemented Paradigm (Version 18.4.4984.0; McKenzie, 2017) a computerbased blast modeling software to improve the learning environment.

Jan 1, 2019

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Wang Xuguang Shen Yingfeng

Structure is the main aspect affecting the performance of emulsion explosive. Calculation of such structure parameters as osmosis pressure, interface area per unit volume etc. must be helpful to the understanding of the structure of emulsion explosive. This paper has solved the Laplace-Young Equation for simplified monodisperse emulsion system by Galerkin method, and gained the relationship between mean curvature, contact angle, volume fraction, fractional film area and interface area per unit volume. The paper also presents a new expression of osmosis pressure at non zero contact angle.

Jan 1, 1998

Current research in comminution includes efforts to increase the efficiency of mineral processing systems and reduce the amount of electrical energy needed for size reduction. In most mining operations, comminution begins with blasting. Normally, blast design focuses on loosening material for excavation and sizing the product for efficient haulage. It is likely that blasting also results in internal damage to rock fragments within the blast pattern which may provide subsequent comminution benefits. If substantial comminution benefits exist, appropriate modification to blast pattern design may reduce the overall electrical energy needed for mineral liberation.

Jan 1, 1996

By Tim A. Beattie, John R. Grant, David L. Kennedy

After many years of research, ICI staff have developed a numerical modelling system for the study of detonator/primer/explosive configurations. Results from this work clearly identified that current primer designs were not as effective in delivering their energy potential as needed. Alternative designs were evaluated and several prototypes, all essentially spherical in shape, were built for testing. Results have shown a significant improvement in various aspects of primer performance, including omni-directional pressure transferral and increased energy release rates. Reliable, high performance priming of explosives is now achievable for a much wider application range.

Jan 1, 1991

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By C. Pelley, S. Kelebek, G. Kunzel, P. Katsabanis

Small blocks of granodiorite have been subjected to blast loads from a single borehole and from a series of boreholes detonating at various timing intervals. The damage of the blocks was assessed through P-wave velocity monitoring, measuring the change of the point load strength index of the rock after dividing the large blocks into smaller ones and measuring the work index of the material at different distances away from the blasthole. Numerical modelling with the AutodynTM code enabled visualization of damage. It was shown that damage is optimum at a small delay time between successive holes while it drops rather drastically after this point.

Jan 1, 2003

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Malcolm Scoble, Yves Lizotte, Ajit Singh

Fragmentation size assessment faces difficult problems, traditionally involving tedious and time consuming procedures. Early work had been directed towards developing empirical methods of predicting rather than measuring fragmentation. More recent development of computer-based image processing techniques which derive size distributions by analysis of photographic or video images are reviewed. These are now being adapted by various workers to fragmentation analysis in mines. Results are presented from experimental work aimed to establish the accuracy and precision of photographic techniques for muckpile assessment. Reference is made to McGill fragmentation studies at surface and underground mines in Canada, relating to experience gained in photographic and image processing techniques. The various factors that affect such techniques as well as their limitations and strengths are discussed.

Jan 1, 1990

By Syed M. Tariq, Paul N. Worsey

Pre-splitting is now widely used to minimize overbreak and to protect final surface rock excavation profiles in large scale civil construction projects, open pit mining and quarrying. Jointing has been shown to affect the success of pre-splitting and the smoothness and integrity of the resulting rock face. Many facets of jointing have been investigated in detail, including the inclination of joints with respect to the desired pre-split plane, the effects of various filling materials, etc. However, the effects of joint frequency and spatial positioning has been paid little attention. The paper addresses this issue.

Jan 1, 1995