Search Documents

By D S. Preece

The aim of the present work is to investigate the effects of shooting multiple explosive charges, in the same borehole, on the amplitude and frequency content of the generated seismic wave. The work also investigates the effect of the coupling medium used in the borehole on the quality of the generated seismic wave. The delay period between the shots is on the order of months and up to a year. The investigation utilizes a numerical modeling approach which is capable of modeling the detonation of explosives as well as shock and stress wave propagation in solids.

Jan 1, 2012

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By Ruilin Yang

The following simple equations are frequently used within the blast vibration community;PPA f PPV v = 2p · , PPV f PPD d = 2p · ,a f PPV PPA 2p = , and v f PPD PPV 2p = where, PPA is the peak particle acceleration, PPV is the peak particle velocity, PPD is the peak particle displacement, and fa , fv , and fd are the frequency of the particle acceleration, particle velocity, and particle displacement vibration waveforms, respectively. Conceptually, the frequency should be selected to be the frequency of a simple sinusoidal wave that is used to approximate the blast vibration. In the literature, f is sometimes chosen as the dominant frequency (fdm) estimated from the Fast Fourier Transform (FFT) of the blast vibration wave, on other occasions, f is chosen to be the principal frequency (fpr) from the vibration cycle with the peak vibration amplitude.

Jan 1, 2012

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By George D. Raitt

Anyone who has spent any time in and around the drilling and blasting profession knows that probably the most critical part is the drilling portion. A blasthole is nothing more than a cylindrical vehicle designed and strategically situated to hold and contain an explosive charge so that it can be detonated in the most efficient and optimum manner possible. It matters very little if the latest “State-of-the-Art” explosive or detonation system Is employed if the hole is poorly placed; i.e. excessive burden and spacing, sized incorrectly for desired results, insufficient in depth etc.. This is not to mention that the drilling phase is the most expensive, requiring sizeable initial outlays and upkeep. It’s also true that improper drilling can cause costs to skyrocket throughout the remainder of the work cycles such as excavating and hauling, crushing, screening and so on.

Jan 1, 1990

By Stanton Johnson

Africa has a long history of mining and has been one’of the world’s greatest sources of gold and other mineral resources since the days of the Egyptian pharaohs. Mining in Africa has been dominated by South Africa since World War II. However, in the past 10 to 15 years, other African countries are beginning to slowly catch up with South Africa. Ghana, formerly called the “Gold Coast” is located on the West Coast of Africa. Ghana has been involved in mining activities for well over 100 years. Most of the mining activities centered on the mining of gold and were to a large extent limited to underground mining methods. With a more liberal economic policy regarding the exploration and exploitation of Ghana’s mineral resources, mining activities are beginning to evolve to a much larger scale. Drilling and blasting which is an important aspect of this evolution is also changing due to the involvement of foreign-based mining and explosives companies.

Jan 1, 1998

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By William Hustrulid

Pre-split blasting is a primary technique for creating slopes with a minimum amount of unwanted damage to the remaining rock mass. Rock slopes created in such a way have both safety-related and economic advantages. The applications extend from road cuts to rock quarries to large open pit mines. For example, as deep open pit mines approach the end of their operating lives, slope steepening is one option to be considered. To be able to safely achieve and maintain steepened final slopes, good blast design techniques must be available and applied together with close operational control. Pre-split blasting is an important element in this slope creation process.

Jan 1, 2007

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

No blast evaluation is complete without fragmentation measurements which until now were inaccurate, costly, time consuming and created delays in production. “WipFrag.s”is a fully automated PC based fragmentation analysis system that uses digital photo analysis techniques to measure broken rock. Fragmentation can be measured in minutes using compact videocameras for image acquisition. Even subtle changes in rack quality can be detected providing the information necessary for pattern optimization, explosives evaluation, timing selection, benchmarking and blast model validation.

Jan 1, 1995

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By He Guangyi

Combining living examples, the paper introduces the controlled chamber standing shot of more than 3000t explosives initiated at one time with Nonel under complicated circumstances and the experience obtained to keep environment safe and favour mechanical rock cleaning.

Jan 1, 1998

By Noel Dent

Increasing interest is being expressed in the development and availability of Electronic Delay Detonators throughout the world. Particularly in open-cast mining, the benefits associated with precise, reliable initiation systems are perceived to be considerable. Many of the systems currently being developed have sophisticated programming requirements associated with them, or are numbered systems that require predetermined layouts to determine timing patterns, and importantly are far more expensive than existing initiation systems.

Jan 1, 1994

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

By Nick Lewis

Farce Mining of Texas is a surface coal mine located in Laredo, Texas. Farce mines and sells approximately 600,000 tons /year of bituminous coal. A map showing the location of Laredo is provided in Figure 1. As shown, Laredo is located on the border between the United States and Mexico. The mine property runs to the Rio Grande River, the border between the two countries. Farce pumps water from the Rio Grande for use in their coal preparation plant. Laredo’s climate is quite dry with annual rainfall averaging about 12” per year. Also, due to the southern location, Laredo is quite hot. It is common for the temperature to reach 100” F in March and maintain these temperatures through September.

Jan 1, 1994

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

By Janice K. Means

The purpose of this paper is to provide the seminar attendee with: information on pipeline construction, operation and standards to better equip him (or her) to analyze the ultimate effect of blasting stress on pipelines; an introduction to the analysis of blasting effects to pipelines using the American Gas Association analysis method; and; supplemental sources useful in the analysis of blasting effects to steel pipelines, and, in particular, on natural gas pipelines.

Jan 1, 1992

By Dennis L. Paisley, Thomas P. Turner

Laser slapper detonators are the next generation detonator under development at the Detonations Systems Group at Los Alamos National Laboratory and function very similarly to an electrical slapper. A fiber optic transmits a laser pulse to ablate a thin metal film. This film, or flyer as it is commonly called, is launched through a short barrel to km/s speeds. The flyer shock loads or slaps a high density pressing of secondary explosive, setting off a detonation therein. Laser slapper detonators afford a number of safety advantages over other conventional detonators. Most important they require very high peak laser powers to operate, orders of magnitude larger than possible sources of natural or man-made accidental stimulus. Because light is transported over fiber optics, laser slappers avoid many of the electrical hazards associated with detonators. Use of insensitive, secondary explosives makes these detonators safer to handle, manufacture, transport, and deploy.

Jan 1, 1994