Search Documents

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By Robert L. Frantz

The performances of the three bituminous coal demonstration methane re¬covery boreholes, located in Greene County, Pennsylvania, are reviewed. Development of these vertical holes was largely underwritten by project funds. Reference is also made to an anthracite coal methane project in Luzerne County, Pennsylvania. This involved one vertical hole and was underwritten by a utility company. In addition, an exploratory drilling in the southern anthracite, which provided the project group with coal cores for methane gas analysis, is also cited. The technical and economical data that were gathered from the various methane projects are analyzed. Finally, the advantages and disadvantages of methane recovery by vertical boreholes are assessed.

Jan 1, 1978

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By P. B. Ritter

The feasibility of redesigning and adapting the all- secondary-explosive, low-voltage, electric safe detonator for use as a delay detonator has been demonstrated. Experimental results have shown that operational characteristics can be adjusted to allow direct competition of safe delay detonators with commercial delay blasting caps. Five different experimental delay period models have been developed and tested. Test results are given and results are evaluated. Subsequent simplified and improved designs for practical and economical mass production are described. Design concepts to meet Bureau of Mines voltage withstand, incendivity, and spark sensitivity requirements are included. Recommendations are made for experimental procedures to ready the safe delay detonator for mass production and extensive use in mining and other industries.

Jan 1, 1977

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By Yoginder P. Chugh

This study has appraised available deeper soil loosening equipment in the 1-4 ft. depth range, in the U.S. and abroad which has potential for Illinois prime farm-land reclamation. The appraisal was based on written and/or oral contacts with equipment manufacturers, reclamation experts, and visiting with selected equipment manufacturers. The results indicate that several manufacturers in the U.S., West Germany, and England market static and vibratory deeper soil loosening equipment which may have potential for application in Illinois. The pertinent information concerning each equipment with potential is presented in this report.

Jan 1, 1983

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By George A. Savanick

This paper reviews advances in the art of borehole (slurry) mining made by the Bureau of Mines from 1974 to 1980. The design of a proto-type borehole-mining tool (BMT) developed by the Bureau of Mines is pre-sented along with production data, reclamation data, and an application of the BMT to the mining of coal, uraniferous sandstone, oil sands, and phosphate ore. The BMT was first used near Wilkeson, WA, where steeply pitching metallurgical coal was mined at 8 st/h from a depth of 25 to 75 ft. Next, 940 st of uraniferous sandstone was mined at 8 st/h from a depth of 75 to 100 ft in Natrona County, WY. One thousand short tons of oil sands was mined in Kern County, CA, at the rate of 14 st/h from a depth of 110 to 150 ft in 1979. Most recently, 1,700 st of phosphate ore was produced at 25 st/h from deep (230-to 250-ft) deposits in St. Johns County, FL. Progressive improvements were made in the borehole mining technique. These include the use of the hydrostatic head of a water-filled borehole for roof support, and the development of methods to survey and backfill mined-out cavities.

Jan 1, 1987

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985