Search Documents

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By H. G. Hammon

Uranium miners have been shown to develop lung cancer in direct proportion to the time of exposure in the mine and the concentration of radioactivity (cumulative working level).1 Radon gas is continually evolved from the uranium ore, but because of its shoe half-life, 3.82 days, it is soon decomposed into particulate daughter products, which along with the dust in the mine, become deposited in the miners' lungs. At present, massive ventilation is the only effective method of reducing the radioactivity concentration in the mines. However, the Bureau of Mines is evaluating the possibility of using coatings on the mine wall that will have sufficiently low permeability to radon that the gas will decompose into the particulate daughter products before it can permeate the coating. Permanently trapped in the coating, the daughter products would be prevented from dispersing in the mine atmosphere. Lawrence Livermore Laboratory was asked to aid in this investigation. The direct determination of radon permeability is more difficult than that of the other noble gases because of the short half-life of the gas and radioactive contamination of the apparatus. We felt that it should be possible to estimate radon permeation coefficients from other noble gas permeation coefficients. It was noted that the log of the diffusion constants for helium, neon, argon, and krypton, as reported by Meares2,3 plotted to a straight line-against the square of-the gas molecularddia meter. The log of the permeation coefficients also plotted to a straight line against the square of the gas molecular diameter. Thus, by determining the permeation coefficients of such gases as argon and krypton through various films and coatings, it appeared likely that radon permeation coefficients could be estimated. In addition we felt it should be possible to find some relationship between polymer structure and he noble gas permeation coefficient that would aid in the selection of coatings materials as radon barriers.

Jan 1, 1975

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

By Don] [Hinkle

Unable to Load

Jan 1, 1977

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962