Search Documents

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By R. L. Blake

The crystal structure of hematite, a-Fe203, has been refined as part of a continuing study of the behavior of phases in the Fe-O system during reduction and oxidation. Three-dimensional diffraction intensities were collected on two spherical single crystals of hematite with a semiautomated Buerger single-crystal diffractometer. The first crystal refined was a natural Elba hematite with minor impurities. The other, a synthetic crystal, was refined at the request of Mossbauer spectroscopy investigators concerned with impurities in the natural crystal. The structure has been refined with a least-squares program and the final structure for the natural crystal irradiated with CuKa-radiation gave a discrepancy factor (R) of 3.65 percent using 49 unrejected reflections of the 51 measured. For the synthetic crystal, using MoKa-radiation, the discrepancy factor converged to 2.8 percent using 95 unrejected reflections and was 3.3 percent for all 109 reflections. The structure model of Pauling and Hendricks has been confirmed with essentially no change in the iron coordinates and approximately a 5-percent change in the oxygen coordinates. Selected interatomic distances and angles were calculated as were anisotropic temperature factors.

Jan 1, 1970

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By J. Mitchell Linne

In 1986 at the request of Bureau of Land Management, the U.S. Bureau of Mines studied 23,225 acres of the 27,980-acre Jordan Craters Wilderness Study Area (OR-003-128) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 20 miles northwest from Jordan Valley. No mining activity has been recorded within the study area, and no metallic or industrial mineral resources were identified. Small isolated occurrences of decorative quality stone were identified. However, none of these occurrences constitute a resource. Although the study area is underlain by relatively young volcanic rocks, the area has no known geothermal energy resource.

Jan 1, 1987

By Levent Ozdemir

A 6-ft. diameter laboratory tunnel, raise and shaft boring machine was designed and constructed to carry out research investigations to enhance the performance of mechanical rock excavation equipment. The machine is operated with a computer control system and features extensive instrumentation to monitor and record various test parameters, including tri-axial cutter forces, machine thrust, torque, rpm and penetration rate. An extensive laboratory testing Program has been conducted using this machine, demonstrating the feasibility of attaining high rates of penetration in various sedimentary geologies. Also, a large data base has been developed to serve as a basis for the improved design and performance of tunnel, raise and shaft boring equipment.

Jan 1, 1986

By John C. LaScola

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1980

By Rudolf E. Grauer

[ ]

Jan 1, 1981

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

[nder ' 1Oclific?atic>n 1 l', of Cant r Ict No. S012?U7 , the T1. S. l urc ,:i.11 of Miries ontracted tivit.l '1 -l:eudurn? Barry t1rirl ,~:>:'nci.11c:, for the 1>crfcocrnancu of a afet, Analynin Q::tc n Study to develop a plan for thc organiration nrld opera¬ion of a 'Lur('an ,`,afutj i ily ;i Cn11tur, r Before the con)y)lctic>n of the stucly, the Abiretu.l ustaldish d such a center, the WniL1, and Safety i?'\naly:-.in Cnmtor (l1S;'J:), under the dirucHan of fly, Assistant Director of JTc'"?ltl) 11111 .itut~ 1O1- 'l (.. -11: 'C'a) :_'-, ?'( )'t. 11. ~.C is 11 c' iC1cnlC:rtc:rr'd at the 1)crnv(jr Federal Center, 1)u:r',L C,r_i1f,U, rK.]

Jan 1, 1972

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By Lon A. Williams

This appendix contains drawing lists and drawings of components and assemblies designed for the prototype portable and machine mounted lighting systems per Tasks II & IV of Contract No. H0220065.

Jan 1, 1976