Search Documents

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By E. L. Singleton

The Bureau of Mines investigated extraction of aluminum from aluminum-silicon alloys as a means of utilizing domestic aluminum silicate ores for aluminum production. Aluminum was extracted from aluminum-silicon alloys by electrolysis in molten electrolytes of NaCl-KCI-AIC13 and NaCl-KCI-AIF3 in a laboratory-scale cell. Six alloys with aluminum contents ranging from 20 to 87 percent aluminum were tested, and aluminum products of primary grade or better were obtained. More than 80 percent of the aluminum was recovered with current efficiencies as high as 91 percent. Recovery of a metallurgical-grade silicon product from the anode residue by an acid leaching procedure was possible with the 50-50 and 65-35 Al-Si alloys.

Jan 1, 1972

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By R. V. Ramani

This report is volume 2 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Geology and Reserves subsystem of the Master Design Simulator. The two functions of this subsystem are: 1) the design of a geological data library to provide input to the other subsystems of the simulator; and 2) the calculation of coal reserves and associated values and grades under various user-specified conditions. The subsystem uses a weighted moving average method to interpolate between the borehole values, and provides output in report format, graphical plots and/or storage on magnetic tape or other storage devices for later retrieval. The application of the subsystem as an independent model with test results and comparisons with other methods of computing reserves is also presented. The appendix comprises a users manual for the model, and includes a program listing.

Jan 1, 1974

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By A. R. T. Denues

Liquid oxygen explosives are ordinarily made from a carbonaceous absorbent and from liquid oxygen of high purity. These explosives have a limited but definite field of usefulness; their properties have been described in the literature, which includes several publications of the Bureau of Mines, the most recent dealing with fire-retardant treatments.3/ It seems generally conceded that the outstanding hazards in the use of these explosives are their high inflammability and their relative sensitivity to mechanical action. Each of these topics has been studied, and some interesting practical results have been obtained. Treatments have been described[7] that render liquid-oxygen explosives prepared from granular carbonaceous absorbents practically immune to the action of igniting agents representing or exceeding practical hazards in violence.

Jan 1, 1941

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By Merle L. Bowser

The Bureau of Mines has developed a portable recording methanometer that utilizes the Bureau's methane sensor. The methanometer can operate continuously for at least 30 hours on small, sealed, rechargeable lead-acid batteries.

Jan 1, 1969

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935