Search Documents

By Thomas J. Peters

A mineral survey of the Sill Hill RARE II area (No. 5304), covering 5,200 acres (2,100 ha) of the Cleveland National Forest, San Diego County, California, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey. This survey was in conformance with the Resource Planning Act (RPA) of 1974, as amended by the National Forest Management Act of 1976, to provide mineral resource information for study area classification. Bureau of Mines personnel made an economic appraisal of mineral deposits by searching pertinent geological and mining publications as well as U.S. Bureau of Land Management, U.S. Forest Service, and U.S. Bureau of Mines files and records. Known mines, prospects, and mineralized localities were examined during 1981, and sampling and mapping were done where warranted. The Geological Survey 'did geologic mapping, geochemical sampling, and geophysical surveys to aid this study.

Jan 1, 1983

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Mary F. Koehler

Continuing a program of thermochemical investigation of compounds of to ferroalloy elements, this paper contains ins values of the heats of formation of two sodium molybdates (Na2Mo04 and Na2Mo207) and three sodium tungstates (NO2W4, Na2W207, and NA2W207, and Na2W4013). The experimental method was solution calorimetry. The solution medium was sodium hydroxide solution, except that hydrofluoric acid solution was used for sodium tetratungstate. The heat of formation values are given with reference both to the constit¬uent elements and to the constituent oxides. These data are of prime impor¬tance in the thermodynamic consideration of these substances, as their accumulation includes the most difficult and time-consuming steps toward evaluating the free energies of formation and thus the potential reactivities and thermal stabilities. Except for values for sodium monomolybdate and monotungstate, no previous similar data were contained in literature sources.

Jan 1, 1962

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining' the potential fur reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By Laxman S. Sundae

A Bureau of Mines investigation was conducted to determine the effect of specimen volume on the apparent tensile strength of disks of St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite. The investigation used a technique developed by the Bureau to determine apparent tensile strength. Because the test specimens were selected without macroscopic defects, that is, cracks, joints, and planes of weakness, the strength variations are solely due to microscopic features. Several replications of each test were performed. Data for each set of specimens were fitted to a power law of the form y = axb, where y = apparent tensile strength, x = specimen volume, and a and b are constants. This power law is essentially a form of Weibull's theory. The average coefficients of correlation for St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite were 0.85, 0.53, and 0.78, respecitvely. In all cases a decrease in strength with increasing volume was noted; in the extreme case, a decrease of 40 pct was noted with an elevenfold increase in volume. The decrease in strength with increasing specimen volume is explained in terms of Weibull's theory.

Jan 1, 1974

By Gilbert A. Wray

This report presents the results of a study of the overturning Stability of Front End Loaders and the development of an Obstacle Detector to warn of Obstacles in the blind regions of the vehicle. The contributing factors have been identified, the FEL stability characteristics have been determined and six overturn warning indicators were fabricated and two were field tested in a mine operation over an extended time period. A simplified overturn indicator, based on the principle of sensing wheel load, was designed, constructed and field tested. The principle was demonstrated to be sound, however, the method of sensing wheel load must be revised. An obstacle detector capable of detecting a man sized target at ranges of two feet to one hundred feet was designed. A "Breadboard" device utilizing existing microwave devices was constructed and tested successfully.

Jan 1, 1977

By Jack O. Jones

The Furnish mine, Caharrus County, W. C., was operated intermittently until 1905 as a gold mine. Scheelite was discovered by A. L. Mash in the mine dumps of the Furniss and Phoenix mines, and he later informed the Bureau of Mines of his discovery. The Bureau of Mines, in two projects at the deposit in 1948 and in drilled 12 holes totaling 1,706.6 feet, examined and sampled the underground workings, excavated by bulldozer and hand, 3,155 linear feet of trenches and collected numerous samples for assay. The best scheelite shown; was found in the underground exposure of the Furniss mine.

Jan 1, 1950

The strike of the Canadian asbestos miners entered its seventh month with increasing signs of early termination. Both unions are in the midst of heavy negotiations with management, and an optimistic industry source predicted that work would resume by October 1. Recession recovery in some segments of the asbestos manufacturing industry is being impeded by lack of fibers, CADMIUM - On September 9, St. Joe Minerals Corp. reduced the price of cadmium metal to $2.75 per pound. The producer price bad been uniformly quoted at $3.00 per pound since June 26, 1975. Subsequently, Amax, Inc. and National Zinc Co. reduced their prices to $2.50 per pound. By mid-September all five U.S. cadmium producers were marketing the metal at $2.50 per pound.

Jan 1, 1975

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982