Search Documents

By Fred N. Kissell

In This Chapter [Instruments available to measure methane in mines and tunnels Using a portable detector in both accessible and restricted spaces Machine-mounted monitors: placement and response time Calibration of catalytic detectors for different gases and Misinterpreting warning signs This chapter gives guidelines for methane measurement in mines and tunnels. The emphasis is on the measurement procedure and the interpretation of the measurement rather than on the instrument itself.] The failure to properly sample for methane is a major contributing factor to methane explosion risk. Sampling errors are most likely to occur at mines or tunnels where the presence of methane is not suspected or during nonroutine tasks at mines or tunnels known to have gas. More specific information on methane sampling at continuous miner sections is in Chapter 3. Chapters 4 and 5 discuss sampling at longwall sections, and Chapter 14 discusses sampling at tunnels. METHANE DETECTORS FOR MINING Many models of gas detectors are available to measure methane concentrations, as well as most of the other contaminant gases found in mines and tunnels. An example is the iTX Multi-Gas Monitor, a portable gas detector available from Industrial Scientific Corp., Oakdale, PA. This handheld instrument measures several gases simultaneously. The cost (2004) ranges from $1,300 to $2,200, depending on the number of gases measured. Similar instruments are available from other manufacturers. Most methane detectors used in mining use a catalytic heat of combustion sensor to detect methane and other combustible gases. These have been proven through many years of reliable operation. For detection of methane, proper operation of catalytic heat of combustion sensors

Jan 6, 2006

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

This paper has peen translated from the Russian by the United States Bureau of Mines and is issued as one of a series of circulars dealing with mining methods and costs in connection with a general study of this subject sponsored by the bureau. The paper presents some interesting features in connection with the methods employed in Russia and describes certain variations in standard methods which might conceivably be applied to a limited extent in this country.

Jan 1, 1930

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East, providing more than 80 % of the region&apos;s foreign exchange. In 1992, the 15 countries that constituted the region accounted for 29.5 % of world crude petroleum output, 20 % of world natural gas plant liquid production, and 5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. A fairly wide range of non fuel minerals is also produced in the region. The most significant are boron minerals, bromine, chromite, gypsum, phosphate rock, potash, strontium, and sulfur. However, the variety of minerals produced, output levels, and the size of the overall non fuel mineral economy of the region is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, was first in world production of run-of-mine boron minerals, second in strontium behind Mexico, and fourth in pumice. It was also a significant world producer of chromite, magnesi&apos;lm compounds, mercury, and sodium sulfate. Turkey was also the Middle East&apos;s largest cement and steel producer. Iran continued to expand output of most mineral commodities following the war with Iraq from 1980 to 1988. It was a significant world producer of gypsum and strontium and on its way to becoming a major iron and steel producer in the region. Despite a very small domestic mineral industry, Israel was second in world production of bromine and a significant producer of phosphate rock and potash. In terms of processed minerals, Israel was a major world diamond cutting center and exporter of cut diamond. Jordan ranked sixth in world production of phosphate rock. Saudi Arabia was eighth in world production of sulfur.

Jan 1, 1994

By James R. Boyle

The value of Alabama&apos;s nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32&apos; F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By M. A. Mahtab

This report presents the geometric parameters (attitude, spacing, extent, and aperture) of fracture patterns in a selected portion (study area) of San Manuel copper mine, Arizona. The geometric parameters are quantified for input to structural analyses for studies of the influence of fractures on cavability of ores. Using an orientation analysis procedure developed earlier by the Bureau, three prominent and nearly orthogonal sets of fracture orientations were delineated in the study area. Sets 1 and 2 dip nearly vertically, and generally strike east-west and north-south, respectively, whereas set 3 is nearly horizontal. Both a horizontal rotation (of 14° to 26° for sets 1 and 2, respectively) and a tilt (of 20° for set 3) is shown to occur between the 1415 and 2015 levels of the mine. Gomparison of the three major rock types present in the study area (quartz monzonite, monzonite porphyry, and rhyolite) show that the rhyolite is characterized by short extent, small spacing, and tightness of fractures as well as the general absence of fracture set 3, which may account for its generally observed strong resistance to caving.

Jan 1, 1973