Search Documents

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By Henry C. Meeves

The nonpegmatitic sources of beryllium in Arizona, Colorado, New Mexico, Utah, and four adjacent states investigated by the Bureau of Mines are described. The investigations included 155 properties from which over 6,200 rock samples were collected; more than 5,500 samples were analyzed by the nuclear beryllium-detection technique. Twenty-four of the properties examined had rock containing more than 0.10 percent BeO. Many of the beryllium determinations were made in the field with portable detection instruments by direct scanning of outcrops and by testing samples of rock brought to the instrument. The large domestic resources of low-grade nonpegmatitic beryllium ore in Utah, which were discovered by private enterprise and which respond favorably to small-scale treatment processes, may come into commercial use and thus reduce the dependence of the United States on imported beryl.

Jan 1, 1966

By Robert D. Thomson

The Bureau of Mines has compiled coal reserve data for the United States as of January I, 1974, for bituminous and anthracite coalbeds 28 inches or more in thickness to a maximum depth of 1,000 feet and for Lignite beds 40 inches thick or greater. These data were organized by State, county, coalbed, and rank. To evaluate the reserve by sulfur content, the reserve and analytical data from the Bureau of Mines energy data bank were synthesized using computer techniques. The reserve base in the Eastern States was determined to be 202.3 billion tons. Bituminous coal accounts for the greatest reserve base: 161.5 billion tons of deep-minable coal, and 32.5 billion tons of strip-minable coal. Virtually all of the anthracite reserve base, 7.3 billion tons, is minable by underground methods. All of the lignite, 1 billion tons, is strip minable. Subbituminous coal is not significant in the Eastern United States, About 14 percent of the bituminous coal reserve base, 26.5 billion tons, contains 1.0 percent or less sulfur. About 87 percent of the anthracite reserve base, 6.3 billion tons, is low-sulfur coal.

Jan 1, 1975

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural-gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of, the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and in solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil-bearing horizons.

Jan 1, 1936

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By Gerald T. Homce, James C. Cawley

Problem: CFOI and SOII data show that 2,287 U.S. workers died and 32,807 workers sustained days away from work due to electrical shock or electrical burn injuries between 1992 and 1998. Method: The narrative, work activity, job title, source of injury, location, and industry for each fatal electrical accident were examined. A primary causal factor was identified for each fatality. Results: Electrical fatalities were categorized into five major groups. Overall, 44% of electrical fatalities occurred in the construction industry. Contact with overhead power lines caused 41 % of all electrical fatalities. Discussion: Electrical shock caused 99% of fatal and 62% of nonfatal electrical accidents. Comprising about 7% of the U.S. workforce, construction workers sustain 44% of electrical fatalities. Power line contact by mobile equipment occurs in many industries and should be the subject of focused research. Other problem areas are identified and opportunities for research are proposed. Impact on Industry: Improvements in electrical safety in one industry often have application in other industries.

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Hisataka Sakakibara

Although the pathophysiology of vibration-induced white finger (VWF) is still under discussion, evidence has been accumulated to understand the underlying mechanism. VWF is pathophysiologically characterized by an enhanced vasospastic response to cold, which can result from an imbalance between vasoconstriction and vasodilation in the digital arteries in response to cold (i.e., vasoconstriction-dominant). The imbalance is supposed to be due to faults in vascular vessels and sympathetically mediated vascular tone. Enhanced vasospastic response to cold Narrowing of arterial lumen with medial smooth muscle hypertrophy. Possible functional factors for enhanced vasoconstriction • Increased sympathetic nervous activity to cold (e.g., norepinephrine) • Increased release of endothelin-1 (ET-1; an endothelial-dependent vasoconstrictor) from the endothelium • Increased reactivity of alpha2-adrenoreceptors to cold Possible functional factors for decreased vasodilation • Decreased release of nitric oxide (NO; an endothelial-dependent vasodilator) from the endothelium • Decreased release of calcitonin gene-related peptide (CGRP; a vasodilatory neuropeptide) from sensory afferents The question is how their interrelations or imbalances among them are Vibration and arterial damage The next question is, how does hand-arm vibration exposure induce such pathophysiological changes in VWF patients? Recent morphological evidence from animal experiments shows that vibration acceleration stress (including shear stress) and smooth muscle contraction contribute to arterial damage of smooth muscle and endothelial cells. The vibration-induced arterial damage is frequency-amplitude-dependent.

Jan 6, 2006

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By James A. Wasson, Harry R. Johnson, Dean W. Boley

The Cow Run sand was cored and electrical and radioactivity surveys were made in C. E. Vandevender well 35 in the Burning Springs pool of the Burning Springs oilfield , Wirt County , W. Va . Laboratory tests , reservoir - fluid analysis , well - log interpretation , and available field data indicate that a substantial quantity of oil may be recovered from this pressure - depleted reservoir by waterflooding . Two formations erroneously believed to be the First and Second Cow Run sands were similarly evaluated in A. E. Mackintosh well 8 , Anns Run Pool , Wirt County , W. Va . , but were found unsuitable for secondary - recovery operations .

Jan 1, 1964

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By James S. Browning

[The objective of this project wan to determine the technical feasibility of recovering the associated copper, lead, and zinc from the pyrrhotite axe, of the Great Gossan lead, which has bon pined only for it:, sulfur and iron contents so far. The report constituted a description and discussion of small-scale Preliminary studies. This great pyrrhotite or body has strategic value, inasmuch it contains considerable quantities of zinc, copper, and lead, as well as the iron rend sulfur. The recovery of the: copper, lead, and zinc, associated with certain of the pyrrhotite ore bodies, could augment our domestic supply of these metals.]

Jan 1, 1953

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By A. E. Ketler

This report describes a variety of coal mine lighting projects which were funded by the Bureau of Mines in order to obtain underground lighting experience in support of new lighting requirements for underground coal mines. Low coal and high coal, narrow and wide entries, conventional and continuous mining, ac and dc power, bituminous and anthracite, and machine mounting and area lighting were some of the variables covered in this program. Also evaluated was the OCENCO fluorescent caplamp.

Jan 1, 1979

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010