Search Documents

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By Robert W. Geehan

The Bureau of Mines has been developing deposits of critical and essential minerals in the United States since 1939. A preliminary examination of the Union lead mine was made in November 1944 and January 1945 by W. T. Benson, a Bureau of Mines engineer, who recommended development by diamond drilling. The Bureau conducted a drilling project at the mine from February 12 to May 16, 1947. The property is in sec.12, T. 17'N., R. 19 E., Mount Diablo Base and Meridian, in. southern Washoe County, Nev., about 15 miles south of Reno. The Union lead mane, also known 4s the Commonwealth mine, has been an intermittent producer of zinc-lead-silver ore since 1860. During World War II, ore was shipped to smelter& near: salt Lake City, Utah. The Bureau drilled 21 diamond-drill holes having a total length of 1,549 feet and 20 long percussion-drill holes with a total length of 359 feet. The program was designed to test for horizontal and vertical extensions of the ore body and to prospect for parallel ore bodies. As a result of this program, extensions of the ore zone were established, but no parallel ore-bearing structures were found. The areas drilled were limited by drill sites available.

Jan 1, 1950

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By W. T. Benson

Peacetime production of mercury in the United States is controlled by world mercury prices, with significant lags to be expected between price increases or decreases and resultant increased or decreased production. Twenty-four mercury-bearing mines and prospects in widely separated districts in western and central Nevada and one property on the Nevada-Oregon border were examined and sampled. The purpose of the project was to determine if some of the properties warranted more extensive exploration work to obtain information on possible reserves of commercial-and sub-commercial-grade ores. The investigation of mercury deposits in Nevada was sufficiently widespread and indicated several areas of interest in the State that merit further exploration work.

Jan 1, 1956

By J. J. Taber

This is the final report on Grant No. G0144067. The report presents the results of a number of laboratory studies carried cut in several different ways to determine the effectiveness of foam for blocking the flow of gas in coal. The effectiveness; (of foam for retarding or blocking the flow gas in various porous media has been observed by many investigators1-4 but we are not aware of similar detailed studies in coal. Because of the diversity of our experiments, the key findings and general conclusions are presented very briefly in Section II. As a convenience to the reader a complete table of cements is included to enable the reader to find those experiments and studies of greatest interest.

Jan 1, 1976

By S. H. Lorain

This paper, which describes lode gold mining in Idaho county, Idaho, is one of a series on western mining districts being published by the Bureau of Mines. It describes mining and milling practices, gives costs, and discusses transportation, climate, power, labor, and other conditions that affect them. The materiel upon which the paper was based was gathered during a field survey in the summer of 1937.

Jan 1, 1938

By E. P. Youngman

The basic mining law of Netherland India is contained in N. I. Statute 1899 , No. 214 , as amended by N. I. Statute 1910 , No. 588 , and 1919 , No. 4 , which is quoted as the " Indian Mining Law, " the effective date of which was fixed as May 8 , 1907 , by proclamation dated October 12 , 1906. The Indian Mining Law was supplemented by Ordinance No. 38 , of 1930 , which was passed by the Volksraad on March 18 , 1930 , to become effective on October 1 , 1930 ( superseding an earlier ordinance entitled " Government Gazette , " 1906 , No. 434) . An important law with respect to American petroleum rights , Statute No. 23 , passed February 9 , 1928 , approving contracts between the Indian Government and the Netherland subsidiary of a large American oil company , is in the nature of a private law or of an enabling act ( see section of this paper entitled " Rights of Foreigners" ) . Statute 1930 , No. 348 , effective October 1 , 1930 , sets forth in minute detail conditions under which prospecting and mining permits may be granted. Statute 1930 , No. 341 , effective October 1 , 1930 , embodies the police regulations of the mining industry.

Jun 1, 1931

By J. L. Wiley

THIS REVIEW contains abstracts of the technical literature and patents dealing with the history, development, and commercial application of the Bergius and related processes for the hydrogenation, under greater than atmospheric pressures, of liquid and solid carbonaceous materials such as coal, lignite, their distillation and extraction products, pitches and tars, and petroleum and its distillation residues. An attempt has been made to include abstracts of all the published information on this process and of as much of the captured foreign documents and reports compiled therefrom as could consistently be reviewed during the time allotted for the work. Contact with the current literature and patents and review of the foreign documents will be continued and the information will appear in Synthetic Liquid Fuels Abstracts, which is being issued bimonthly as a Bureau of Mines publication. The material in this review is divided in two sections-literature (part I) and patents (part II)-and each of these is arranged alphabetically by author or patentee with further chronological arrangement under each author or group of authors. Secondary authors and patentees as well as assignees are cross-indexed to the main entry. In serial articles or reports the complete series appears in the alphabetical arrangement according to the author of the first member of the series. Succeeding members as well as secondary authors are entered as cross references; Titles of the journals are used as the authors in anonymous references. By following such a procedure, an author index is not required. However, a detailed subject index and a numerical patent list by countries are given as part III.

Jan 1, 1950

By F. D. Stevenson

Thermodynamic properties of metal halides and, in particular, vapor pressures have become of great importance in recent years owing to increased application of chemical processing to extraction of metals from their ores. Vapor pressure data serve not only as a valuable source of latent heat of vaporization and fusion values but also differences in metal-halide vapor pressures often provide the basis for their separation by conventional mass transfer operations. This literature search was made to provide a ready reference to experimental vapor-pressure data of metal halides and oxyhalides. Results are reported in two main sections: (1) A tabulation of vapor- pressure references for each of the metal halides (listed by metal) for which actual experimental data are reported (table 1), and (2) a bibliography of the citations. Metal halides and oxyhalides are listed by chemical formula and chemical name, based on the stock4 system. To facilitate location of the references, a listing of the journal titles and their abbreviations follows the bibliography.

Jan 1, 1963

By J. F. Papp

The microstructures of a CF2Br2-inhibited methane flame and its uninhibited analog have been determined using molecular beam-mass spectrometry. The slightly lean flames were stabilized on a cooled porous plug burner at reduced pressure. Composition profiles of stable, intermediate, and radical species and temperature profiles were obtained. Comparisons of the uninhibited and inhibited flame profiles revealed the following inhibition effects; a shift of the primary reaction zone to higher temperatures, a higher maximum flame temperature, an increase in the CH3 concentration, and a reduction in the H2CO, H, 0, and OH concentrations. Kinetic analyses of the data yielded rate coefficients at flame temperatures for the reactions H + CH4 ? CH3 + H2, H + O2 ? OH + O, CO + OH ? CO2 + H, and CH3 + O ? H2CO + H. CF2Br2 is judged to decay by thermal decomposition and abstraction reactions.

Jan 1, 1981

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By L. T. Grose

The Bureau of Mines conducted a comprehensive study of the Kanab, Kolob, Kaiparowits, and Harmony coalfields of southwestern Utah to obtain additional information and to determine the potentials of these coalfields as sources of energy for steam-electric power-generating plants. Field examinations were made to ascertain the geologic structure and the stratigraphy of the coalfields, the accessibility of the coal-bearing strata, and the general nature of the coal-bearing strata and the terrain. Many mines, both active and abandoned, were examined, and key personnel in the coal industry in the area were consulted. Available analyses of southwestern Utah coals were compiled, and tentative conclusions regarding the rank and quality of the coals were drawn. Coals have been classified by rank according to the standards established by the American Society for Testing and Materials in 1964. The Parr formula for moist, mineral-matter-free British thermal units has been used to calculate the rank of each sample, except as otherwise noted. Water resources related to the areas of the coal reserves also were investigated. Existing literature and maps pertaining to the geology of the areas were reviewed. Production potentials of the coalfields and economic conditions affecting the possible utilization of the coal reserves as sources of energy for steam-powered electricity-generating plants were investigated and analyzed. The data obtained and the conclusions reached as a result of this study are included in this document. The total reserves of subbituminous A and high-volatile bituminous C coals in the fields of southwestern Utah are estimated to be at least 8 billion short tons at depths generally less than 2,000 feet. It appears likely that this estimate will be increased as additional data are made available through exploration and other investigations. Sufficient coal is available in four southwestern Utah counties to supply three or four large steam-electric plants. If the States involved grant water rights to companies planning to build steam-electric plants, the cost of producing power with coal might be attractive and might justify the construction of one or more of these plants.

Jan 1, 1967

Volume 2 presents the results of studies of Phelps Dodge Corporation's tailings embankments numbers 1West and 2 West, at Morenci, Ariz. The work involved compilation and description of pertinent factors relating to the physical features and operational characteristics of the facility, including information on embankment construction practices; investigation and research of the general geologic and seismicity characteristics of the site and vicinity; limited field exploration and materials sampling and testing at the site; installation and limited monitoring of piezometers, surface movement markers, and slope indicator casing; limited laboratory testing of materials to evaluate the basic index and engineering properties of the embankment and tailings materials; selected engineering analyses of the embankment for various types of potential "failure" conditions; and includes appendices.

Jan 1, 1974

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used 1n this report are divided into two components for individual analysis--(1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations. The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By Seth C. Schaefer

The Bureau of Mines investigated the thermodynamic properties of Bi203 (bismuth sesquioxide) and Sn02 (stannic oxide). Standard Gibbs energies of formation (AGfO) of these compounds were determined with high-temperature electromotive force (emf) cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained from the cell

Jan 1, 1984