Search Documents

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By Vernon Helm, John S. Ball, Welton J. Wenger, William E. Haines

"INTRODUCTION Although the presence of sulfur causes many petroleum’s to be classified as ""low-grade"" because of the difficulties encountered in manufacturing products to meet rigid specifications, the petroleum industry is finding it necessary to use such crude oils to satisfy present needs. As the demand for petroleum products increases, and available reserves diminish, this utilization of high-sulfur crude oils will be accentuated. Programs designed to supplement the supplies of fuel available from petroleum by the manufacture of synthetic fuel from natural gas, shale oil, and coal are in progress. Such fuels, especially shale oil and, less so, oil from the hydrogenation of coal, also contain sulfur compounds which must be effectively removed. Thus, the need for fundamental research on the sulfur compounds that may be expected in petroleum and allied products is becoming greater as the industry is forced to call upon all available resources to meet the demand for petroleum products. In recognition of this need, the Bureau of Mines has inaugurated a long-range program assigned to furnish fundamental data concerning the presence, characteristics, and effects of sulfur compounds in petroleum and its products."

Dec 1, 1946

In September 1985, the Chairman of the Transportation, Aviation and Materials Subcommittee of the House of Representatives requested that the Director of the Bureau of Mines address the issue of South Africa and critical materials dependency in testimony before the Subcommittee. Subsequent to the testimony, the Bureau has prepared a technical report focusing on the importance of South Africa and, in some cases, its neighboring countries as suppliers of six key materials. The report includes a qualitative analysis which examines the supply shortfall resulting from a potential disruption, options that are available for mitigating the impact, and their likely effectiveness, and quantitative analyses which estimate the economic impacts in the chromium and manganese markets resulting from peacetime disruption scenarios specified by the Subcommittee Chairman. The concluding section treats the role and capabilities of the Bureau of Mines in dealing with mineral supply disruptions.

Jan 1, 1986

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

By K. K. Kelley

This work is a continuation of a program of study of the measurement and correlation of fundamental thermodynamic data inaugurated several years ago by the United States Bureau of Mines. Previous bulletins in this series were concerned with (1) The Entropies of Inorganic Substances (66),3 (2) High-Temperature Specific-Heat Equations for Inorganic Substances (67), (3) The Free Energies of Vaporization and Vapor Pressures of Inorganic Substances (68), (4) Metal Carbonates-Correlations and Applications of Thermodynamic Properties (71), (5) Heats of Fusion of Inorganic Substances (69), and (6) A Revision of the Entropies of Inorganic Substances-1935 (70). The present bulletin has as its primary purpose the correlation of the thermodynamic properties of elementary sulphur and its inorganic compounds and the presentation, after careful consideration of all available information, of a self-consistent system of thermodynamic relationships for these substances. It is believed that such a set of relationships, concerning substances of such great metallurgical importance as sulphur, sulphur oxides, hydrogen sulphide, metal sulphides, and metal sulphates, is of considerable value in indicating directions of possibly profitable experimental work and in clarifying subjects of technical interest upon which direct experimental information is difficult and expensive to obtain. It cannot be doubted that many problems of technical importance that at the outset appear almost hopelessly complex or obscure either may be solved, if enough information is available, or the specific lacking information clearly indicated by the adoption of the thermodynamic viewpoint. This has been demonstrated many times in the work of the Metallurgical Division, Pacific Experiment Station, Berkeley, Calif. Even when only crude basic information is available, a semiquantitative picture often may be developed by thermodynamic means in which general trends and approximate limits of a proposed process or modification of practice may be clearly portrayed and thus used as guides in further considerations and experimentation.

Jan 1, 1937

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By William L. Crentz

Late in the nineteenth century en active coal-mining industry was begun in the Lower Freeport bed near Reynoldsville, Pa., where the bed thickened to more than 10 feet in places . The coal was readily accepted as an excellent steam fuel. Much of the thick coal his been depleted, but there are many areas where the deposit averages about 14 feet in thickness. As the more desirable mining sites were worked out in the Lower Freeport bed, other beds were exposed from which will come the county's major cowl production in future. The Lower Freeport bed is still the most important bed in Jefferson County from a production standpoint. The Lower Kittanning bed is second. Sporadic mining is being done in the Upper Freeport, Upper Kittanning, Middle Kittanning, Clarion, and Brookville beds. Strip mining has permitted recovery of much coal that could not be mined profitably by conventional underground methods.

Jan 1, 1953

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By Chas. F. Jackson

This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the United States Bureau of Mines and made possible through the cooperation f many mining companies in the United States and foreign countries. The preparation of this paper follows a field study of top-slice mining during which the author visited and discussed with operating officials a large number of iron mines in the Lake Superior region. During this study special note was made of changes in top-slicing practice during the past decade, prior to which the author had acquired several years experience with the method through active connection with a number of mines employing top slicing.

Jan 1, 1931

By Donald I. Kurth

The Bureau of Mines conducted experimental work on comminuting coal. The size distributions of coarse fragments and fine particles were obtained under different modes of energy application--drop, impact crushing, wedge impact, compression, and shear tests. Four levels of energy application were used in the impact crushing and wedge impact tests. Airborne dust and respirable air-borne dust distributions were obtained for the impact crushing and wedge impact tests. Analyses of nonairborne dust and coarse fragment-fine particle distributions were carried out on impact, wedge, compression, and shear tests. The experimental size data on nonairborne dust were fitted to normal, log-normal, power law, Weibull, log-Weibull, and exponential distribution functions. Both the nonairborne dust and the coarse fragment-fine particle size distributions are best described by Weibull distributions. For the impact crushing tests, mean product size was found to be inversely related to specific crushing energy. The particle counts in a given size range of airborne and nonairborne dust were found to increase with increased input energy and specific crushing energy. However, in another sense the particle distributions were independent of energy level; that is, the percent-ages in a given size range were approximately constant regardless of energy level. Respirable airborne dust was related to respirable-size nonairborne dust by a power law.

Jan 1, 1975

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By O. T. Barrett, R. F. Aberethy, H. N. Cooper, Thomas Fraer, William L. Crentz

"INTRODUCTION The object of the techniques described in this report is to determine the possibilities of separating the components of a raw coal into such grades as may be necessary to recover some exceptionally clean functions for special purposes.To do this commercial gravity methods would require separation at very low specific gravities, entirely outside the range of conventional practice. Hence, a technique has been developed for breaking down cool ample, into very close fractions within the gravity range of the (-lean coal matter as well as for separating it from the refuse and particles.Such data on the fundamental specific-gravity consist of the clean-coal matter will serve to appraise the difficulty of the problem and to chow be accomplished if and when effective methods of making such separations commercially are developed."

May 1, 1945

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

This is the initial issue of STATE MINERAL SUMMARIES. This publication provides estimated data and summaries of mineral activities at the State level for 1988. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1989

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

The low production rates associated with the underground metal mining industry have received considerable attention during the last decade. A number of significant technological advancements, in the form of new equipment, have taken place to improve the economics of ore production. Unfortunately, an extremely important factor in the equation -- the operator protection and safety -- continues to receive a low priority. The underground metal mining industry has one of the poorest industrial safety records in the United States. Equipment operators are constantly being placed in hazardous situations. Even one fatality is one too many. All of us bear the responsibility to eliminate it. This project is one of the important steps currently being undertaken by the U.S. Bureau of Mines to improve the operational safety of seven major pieces of ore handling equipment commonly used in underground metal and non-metal mines. The objectives of this study are; (a) to identify the existing hazards associated with the operation of the specific equipment, and (b) to recommend practical solutions that will minimize these hazards and reduce operator injuries. These recommendations are to be in the areas of equipment design improvements, additional operator protection and warning devices, equipment operating procedures and any modifications to the existing safety regulations.

Jan 1, 1975

By John T. Neubert

Between 1988 and 1990, the U.S. Bureau of Mines studied the mineral resources of San Juan National Forest to appraise and determine types and locations of deposits that could be mined economically now and in the foreseeable future. The study included a comprehensive field examination and literature search. Substantial amounts of lead, zinc, copper, gold, and silver have been mined from within the Forest in the La Plata, Rico, Silverton, and Dunton areas. At least one buried 200 million ton stockwork molybdenum deposit occurs in the Rico area. Similar size porphyry copper deposits occur at the surface and about 1,700 feet below the surface in the Bedrock Creek area of the La Plata district. Numerous smaller base-and precious-metal and uranium deposits have been prospected and mined throughout the Forest. Coal, oil, and gas have been or are currently being produced in the western and southern parts of the Forest. Carbon dioxide occurs in the western part of the Forest. Strategic elements occurring within the Forest include platinum, palladium, cadmium, gallium, indium, bismuth, and tellurium; however none of these elements is economically recoverable at present. Several geothermal areas are scattered across the eastern two-thirds of the Forest. Industrial minerals within the Forest include sand and gravel, limestone, and decorative stone.

Jan 1, 1992

By P. Nicholls

Patent records show that the idea that the burning of fuels can be improved by mixing or pretreating them with chemicals 6 dates back to the early years of the last century. By 1845, English and French patents included the specific beneficiations of elimination or reduction of smoke, soot, and clinker; reduction of the ashes, presumably meaning the total weight of refuse from the ashpit; elimination of sulphur fumes; increase in the rate of burning; increase in the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 pounds or more per ton of fuel, but after 1860 the quantity was rarely more than 4 pounds. There is no record of the extent to which these patents were commercialized, but after 1884 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many companies marketed proprietary products that were sold under the general name of "fuel savers." Since its establishment in 1910, the Bureau of Mines has continually received inquiries about these products and, at the request of other govern-mental departments, has tested some used in accordance with the instructions of the purveyors; the results were all negative and, within the accuracy of measurements, the products had no effect on the burning.

Jan 1, 1937