Search Documents

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By Benjamin W. Haynes

This Bureau of Mines publication comprises a compilation of the state of the science in Pacific Ocean manganese nodule mineralogy and elermental composition. The report is divided into three sections: morphology, mineralogy and elemental composition. The nodule morphology section defines what is considered a nodule for the study, and details the external characteristics and internal structure. Nodule mineralogy is discussed in three sections: manganese minerals, iron oxide minerals, and accessory minerals. The major manganese minerals discussed are todorokite, birnessite, and vernadite. The iron oxide minerals are less well known and include feroxyhyte, goethite, and lepidocrocite. Accessory minerals present include quartz, clays, and other silicates and nonsilicates. A discussion on moisture content is also included. The elemental composition section presents data on 74 elements occurring as cations or anions. Summary data, histograms, and interelement correlation coefficients are presented. The elements are grouped as follows: major and minor elements of potential economic interest (8), other major and minor elements (9), elements of environmental interest (8), rare-earth elements (15), precious-metal-group elements (6), radioactive elements (3), other trace elements (17), and anion-forming elements (8). Cross sectional determinations of Ni, Cu, Zn, Co, Pb, Fe, Ce, and Ba are given for a single nodule to show the general tendency of different growth patterns within a nodule because of different element associations and composition.

Jan 1, 1982

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By Albert L. Toenges, Louis A. Turnbull, Alonzo W. Quinn, J. M. Schopf, Arthur Neale, R. F. Abernethy

"INTRODUCTION The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war materiel; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this critical fuel situation, an investiga¬tion was made of possible sources of fuel nearer to points of consumption in New England. Meta-anthracite, which is a satisfactory fuel for some purposes, had been mined in Massachusetts and Rhode Island many years ago. However, the introduction of freer-burning anthracite and bituminous coal into New England markets resulted in the abandonment of these mines.The coal mined in the vicinity of Portsmouth on Aquidneck Island, Newport County, R. I., had been used successfully for smelting copper ore and for fuel. It is reported that this coal is less graphitic than the material mined at Cranston near Providence, R. I. The coal is meta-anthracite and does not burn freely. However, improved equipment for burning coal has been developed, and if minable reserves of meta-anthracite should be found, methods of burning it probably could be devised.The purpose of this investigation was to determine sources of additional fuel. Since meta-anthracite mined at Portsmouth had been used with some success, an investigation was undertaken to determine the characteristics and continuity of the beds in this area."

Apr 1, 1948

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By Charles L. Kimbell

The final 26 tables of this chapter, tables 14-39, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-88 editions. In this year's edition, for the first time, a column has been added to each of these tables providing a 5 year average for 1985-89, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continues to be, as in past years, in descending order of rank in the year of review, 1989. With the inclusion of silver and uranium oxide in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 in terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral of world crude mineral production in 1983. In addition, world output of five key down-stream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil are included because of their significance as products.

Jan 1, 1992

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By D. E. Van Dillen

Seven configurations for panel entries of a longwall coal mine are compared and ranked according to structural stability. These entry configurations are analyzed using three-dimensional finite element modeling The models include large dimensions to minimize boundary effects, elastoplastic constitutive relations, and simulated excavation and construction of support systems. The stability criteria are formulated in a quantitative manner to facilitate the ranking of the entry configurations. These criteria are based on the expected volume of caved rock in the entry openings. The stability ranking is applied to the entry excavation phase, the headgate phase, and the tailate phase of the entry life cycle. Parametric variations are applied using two-dimensional finite element models to determine the sensitivity to changes in mining and design parameters.

Jan 1, 1981

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By WM. H. RINKENBACH, C. A. Taylor

No complete work on explosives, their constitution and analysis, has hitherto been published. Several books that contain chapte.r;s on analysis do not cover the matter thoroughly. Methods tha;t, manu~ facturers, testing stations, and other . agencies have developed to meet their own requirements have not been made public. The Bureau of Mines has issued four publications 1 - cov:eri:ng special phases of the subject. This bulletin. is not inte.nded to replace those reports, but rather to cover present methods employed 'in the , industry and to include all classes of explosives and the materials used in their manufacture. No sharp distinctions can be drawn between classes of explosives. . Surplus military explosives, for example, may be used for blasting, just as blasting explosives, under some conditions, may be employed for military purposes. Moreover, one class gradually merges into another because of similarity in composition. Explosives are here grouped as dynamites, black powders, propellants, detonators, and primers. Some materials are used in practically all these groups ; others in only one. To discuss all the materials that have been or that may be used and the methods for their identification and quantitative determination is not feasible, but the methods described will probably suggest ways of examining new mixtures.

Jan 1, 1923

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By Lester G. Morrell

While developments in Australia dominated the minerals industry of the South Pacific area, New Caledonia's nickel, manganese ore from New Hebrides, gold from Fiji and New Guinea, and phosphate rock from several small islands were significant in world supplies of those materials. The total value of mineral commodities produced in this area in 1965 has been estimated at about $763 million an increase of nearly 16 percent over the value reported in 1964. Increases were recorded in mineral production value with respect to that of 1964 for all of the countries except Papua-New Guinea where lower gold output resulted in a drop of about $300,000 and in the several phosphate-producing islands that collectively recorded a value decline of around $1.3 million. Exploration and development activities continued at an intensified level, not only in Australia and New Zealand but also in the British Solomons, Bougainville, and Fiji. Substantial additions to world supplies of iron ore and bauxite are assured and recent discoveries of natural gas, manganese ore, and nickel combine to give Australia a brilliant mineral outlook. Important discoveries of copper on Bougainville Island and on Vanua Levu, the north island of the Fiji group, and a gold mine on Misma Island were being developed during the year, with plans for early production underway. In New Zealand progress has been made on the New Zealand Steel Company project, and preliminary appraisal of a new titano-magnetite beach sand resource on the South Island has aroused considerable industrial interest. Extensive geophysical investigations were carried out in the British Solomon Islands and on Fiji's goldfields. The expansion program that will double output of products by New Caledonia's Société Le Nickel continued through 1965, and several foreign private companies have expressed a desire to initiate additional industries based on nickel prospects in New Caledonia.

Jan 1, 1967

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By G. D. Jermain

The Bureau of Mines investigated the Gypsum-Camel deposit on Iyoukeen Cove Chichagof Island, Southeastern Alaska, from April 21 to August 26, 1948, as A part of the United States Department of the Interior program for developing an Alaskan construction industry. As gypsum is one of the components necessary for the manufacture of cement and one of the raw materials for plaster and plaster-board products, it is desirable to locate and develop a readily accessible deposit of gypsum in Alaska. In 1928, B. D. Stewart of the Territorial Department of Mines surveyed the gypsum deposits at Iyoukeen Cove, and during the summer of 1946 George M. Flint, Jr., and Edward H. Cobb of the Federal Geological Survey examined and mapped the old workings at Gypsum Creek and the prospect at Iyoukeen Cove. Both the Territorial Department of Mines and the Federal Geological Survey recommended the Gypsum-Camel prospect as warranting a diamond-drilling program by the Bureau of Mines. The Bureau of Mines project consisted of cleaning out and sampling, the old underground workings and diamond drilling from the surface to ascertain the lateral extensions of the deposit.

Jan 1, 1952

By R. R. Sayers

The contemplated use of dichloro-difluorco methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for public buildings and possibly homes, brims attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorino compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines as requested to make a laboratory study of the toxicity and potential hazard, and it was ca the oasis of the results is of this work and the results of a preliminary investigation made in another laboratory6 that the compound has been selected for commercial use. The investigation conducted by the Bureau of Mines is still in progress, enough information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:

Jan 1, 1930