Search Documents

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By Joseph J. Wallace

1. From the standpoint of present production and recoverable reserves, there are two beds of major importance in Allegheny County -Pittsburgh and Upper Freeport -and one of lesser importance -Redstone. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 832 million short tons as of January 1, 1953. Of this total, 768 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Byron A. Baker

The Bureau of Mines used a windowed cell to measure the phase-boundary pressures of two related series of gas-condensate fluid mixtures. Normal butane was added to the mixtures incrementally to determine its effectiveness for lowering phase-boundary pressure. All the experimental data were correlated, so that the pressure required to maintain light oils mixed with natural gas in the single phase may be computed for secondary recovery applications. The heavy hydrocarbon parts of the mixtures were distillation fractions of a Gulf Coast condensate. Intermediate normal hydrocarbons in the butane-heptane range and natural gas were added to the fractions in selected proportions, so that phase-diagram pressures of 26 fluids were actually studied. The experimental range of temperatures was 50° to 280° F. Two correlations were developed to represent phase-boundary pressures by means of a polynomial. Independent variables represent natural gas content, disparity of properties of components comprising the mixtures, and temperature. A fourth variable, for one correlation only, was the quantity of normal butane added to the original mixtures. The latter correlation with four independent variables contains 15 coefficients and is estimated to be accurate to 135 psi.

Jan 1, 1973

By R. B. Porter

Bench-scale tests were performed by the Federal Bureau of Mines on lignite and subbituminous coal at pressures to 1,000 p.s.i.g. (pounds per square inch gage) in atmospheres of hydrogen or nitrogen to obtain information concerning the influence of pressure on carbonization of normally noncaking coals. The distribution of gaseous, liquid, and solid products as a function of processing pressure was determined. Except for special experiments, the carbonization was at 940° F. In a hydrogen atmosphere above 400 p.s.i.g., agglomeration of the solid residue (especially with lignite) became noticeable and increased directly with the processing pressure. Although in some instances the solid particles fused together, the mechanical strength of the agglomerate was always low. On the basis of visual inspection, the coals agglomerated in the following order of decreasing intensity: (1) Steam-dried lignite; (2) lignite; and (3) subbituminous coal. Addition of lignite tar in quantities to 25 percent by weight of charge did not increase agglomeration or change the carbonization characteristics of the coal.

Jan 1, 1961

By M. Hertzberg

The Bureau of Mines measured the energy requirements for the spark ig-nition in air of Pittsburgh seam bituminous coal dust, lycopodium spores, and polyethylene powder with a 1.2-L furnace and 8-L and 20-L chambers. Thermal autoignition temperatures of the same dusts were mea-sured in the 1.2-L furnace. Electrical ignition requirements are given in terms of both effective spark gap energies, [ ] and stored circuit energies, 1/2 CE2. The measured order of electrical ignitability for the three dusts is consistent with the data of other researchers; however, the absolute values are systematically higher, probably because of higher flow and turbulence levels in the chambers used and lower electrical efficiency in the circuit used here. The temperature dependence of the lean limit of flammability for lyco-podium was measured wi th the 1.2-L sys tem, and those measurements con--firm the applicability of the modified Burgess-Wheeler law to a dust. Due to experimental complexities, the minimum ignition energies for dusts may not reflect intrinsic flammability behavior. However, some valuable information may be obtained from the relative ignition energies of various dusts at ambient and elevated temperatures. In addition, the concept of minimum electrical ignition energies for homogeneous gas mixtures is reevaluated theoretically.

Jan 1, 1985

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By Dean H. Ambrose

[Mining and processing earth's materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By W. L. Dare

This report is one of a series published by the Federal Bureau of Mines to describe methods and costs of mining uranium on the Colorado Plateau. The Navajo Uranium Division of Kerr-McGee Oil Industries, Inc., mines uranium from several deposits of carnotite-type ores, which lie buried in the Lukachukai Mountains on the Navajo Indian Reservation, Apache County, Ariz. The country is rugged and isolated Constructing and maintaining roads has been a continuous task. The ore bodies occur within the Salt Wash member of the Jurassic Morrison formation and are similar to other such deposits on the plateau. The current mining activity in the Lukachukai Mountains is a result of uranium-ore discoveries in 1949, although the Navajos undoubtedly knew of the outcrops of yellow uranium minerals long before that time. The ruggedness of the country and the heavy soil cover over much of the surface hampered prospecting, but probably the main reason the ore was not found sooner is that no one took the trouble to look for it in the Lukachukai Mountains.

Jan 1, 1961

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By R. W. Huber

A consumable-electrode arc-melting furnace was constructed at the Bureau of Mines Physical Metallurgy Laboratory, College Park, Md., for the production of uncontaminated titanium and titanium-alloy ingots. The furnace was designed to allow for evacuating to very low pressures and back filling with helium and argon mixtures for melting at or near atmospheric pressure. Vacuum melting at a few millimeters pressure was also used with a mixture of helium and argon gas sweeping the crucible. For research purposes a 25- to 30-pound ingot, 4 inches in diameter by 15 inches in length, was selected to provide, enough 1/2-inch plate for extensive tensile and impact testing of standard size specimens. Enough plate was also provided for testing by other Government laboratories. The homogeneity of several alloy ingots was determined, and excellent results were obtained. By using a large electrode-to-ingot-area ratio and high currents or power inputs to the arc furnace rather uniform ingots were routinely prepared.

Jan 1, 1957

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By Otto Ruhl

As the result of a study of an area comprising some 100 square miles in the Missouri-Kansas Zinc district known to have produced zinc Ore from horizons below the Grand Falls formation, it was concluded that these horizons could become an important future source of zinc. To test this conclusion and to ascertain the general conditions associated with these lower-horizon ore deposits, the Bureau of Mines undertook detailed drilling of localities thought to be favorable for deposition of ore in the Reeds Spring and. Fern Glen formations. Two sites in the Galena, Kans., mining camp were chosen for this purpose. Ninety churn-drill holes totaling 19,338 feet of bore were completed by the Bureau in two campaigns that extended from October 1944 to June 1946. Approximately 25 percent of the holes encountered ore and indicated three separate ore bodies containing substantial tonnages. Observations made during the course of the work revealed that certain structural conditions are common to ore deposits in the Reeds Spring and. Fern Glen formations.

Jan 1, 1949

By E. P. Youngman

In the Unfederated Malay States, with the exception of Johore, the rights of suzerainty, protection, and administration were transferred by giam to the British Government in 1909. In the States of Kelantan, Trengganu, Kedah, and Perlis, the rulers are assisted by State Councils and by British advisers appointed by the British Government.3 With respect to Johore, the largest, richest, and most highly organized of the Malay States not in the Federation, the treaty of December 11, 1885, with Great Britain, defined the relations of the State to the British Govern- ment and allowed the Maharaja to assume the title of "Sultan"; an amendment to this treaty (May 12, 1914) provided that the Sultan should be advised by a British officer, the General Adviser. ...... The political organization of the States is reflected in the mining legis- lation, Johore being the only one having a comprehensive code. The mining enactments now in force, according to the High Commissioner for the Malay States, are as follows:

Jun 1, 1932

By Charles Vaught

The purpose of this study was to determine mine workers' state of fie-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 2010

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack. Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimen first were obtained mainly for the geologic information they revealed; now they are on analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within reservoir and in devising efficient means for their withdrawal.]

Jan 1, 1939