Search Documents

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By John C. Ferm

This report summarizes the results of an investigation of geologic factors that contribute to roof quality in underground mines in the Pocahontas #3 coal bed in southern West Virginia and southwestern Virginia. The investigation consisted of three phases, the first of which was selecting for detailed study five mines which represented the range of roof conditions, mining practices and geologic phenomena. This was accomplished by a statistical analysis of questionnaire data from 35 mines. The second phase consisted of detailed mapping in a "good" and a "bad" top area in each of the five selected mines and resulted in a qualitative assessment of geologic factors contributing to roof £alls. In the third phase, five mines were selected in which most non-geologic factors believed to contribute to roof falls were relatively constant but displayed a wide variety of geologic characteristics. Data from these mines were analyzed to test the qualitative assessments from Phase II. The primary result of this investigation is that slickensides arising from different geologic causes are the major geologic features leading to roof falls. These slicken-sides are found in ancient slump deposits, fire clays and sandy fire clays and channel contacts. Falls also occur where thick sandstone bodies directly over-lying the coal contain abundant shale or ironstone pebbles and coaly strips. The best top material is a sequence which consists of shale grading upward to sandy shale and sandstone within 30 feet of the top of the coal. Thick sand-stone units (301) without pebbles also provide good top.

Jan 1, 1978

By Craig M. Jensen

A laboratory assessment of prompt and delayed neutron activation analysis with 252Cf and 14MeV neutron sources, for use as an in-situ method of determining low-level copper concentration has been performed. A simulated borehole using porphyry ore was constructed and varying copper concentrations were simulated using copper rods. Prompt neutron activation analysis experiments were consistant with earlier work and do not appear to be feasible fur copper concentration of 1.5% or less. Delayed neutron activation analysis experiments indicate that copper ore concentrations of less than 0.1% are detectable using either the 511-KeV gamma-ray of copper-64 or the 1039-KeV gamma-ray of copper-66, with high resolution detectors such as Ge (Li) or intrinsic germanium.

Jan 1, 1977

By E. C. Tarpley, R. A. Drogowski, R. F. Abernethy

Three of the test methods frequently used for the determination of moisture in the analysis sample of coal were employed in analyzing a series of coals ranging in rank from anthracite to lignite . For most coals , the variation between the three methods are within the tolerances allowed between duplicate determinations by the same method . The processing variables studied included atmosphere , flow rate of atmosphere , inert atmospheres , oven temperatures , heating time , exposure of the dried coal to laboratory air , and surface area of the test sample . Unless close control is kept on these variables , erratic results will be obtained .

Jan 1, 1964

By Oliver Bowles

"Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has prompted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believed would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units.The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendation are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many other problems, will bring the most enduring benefits to the industry as a whole, the writer urges that the most earnest consideration be given to this vital problem now facing the slate industry.Grateful acknowledgment is made of the helpful assistance rendered by R. E. Eckert of the accounting firm of Eckert, Degan, and Palmer of Easton, Pa., in compiling the charts and the explanatory text. He has brought to this work a wide knowledge of accountancy, supplemented by a background of direct contact with the slate industry, and his presence at the various conferences has been of great advantage in clearing up difficulties. The National Slate Association sponsored the cost study and chiefly through the efforts of President W. H. Smith and Secretary W. S. Hays, has aided greatly in conducting it. Acknowledgment is also made of assistance rendered by William F. Marsh of the United States Bureau of Mines."

Nov 1, 1929

By Henry H. Ginsberg

The effectiveness of 0.01 pct. molybdenum, as ammonium molybdate impregnated on coal, on the hydrogenation of a high-volatile bituminous C coal at 8,000 p.s.i.g. and 460° to 480° C. has been studied in a pilot plant by the Federal Bureau of Mines. Under these conditions, the Bureau obtained 98 to 99 pct. conversion5/ of coal to liquids and gases at throughputs of 29 to 101 lb. of m.a.f. coal per cubic foot of reaction space per hour. At 460° C. the indicated yield of oil ranged from 63 pct. (based on m.a.f. coal) at a throughput of 35 lb./c.f.h. (pounds per cubic foot per hour) to 68.5 pct. at a throughput of 58 lb./c.f.h., and the yield of gaseous hydro-carbons ranged from 25.5 to 19 pct. at the same throughputs. The maximum measured yield of oil boiling under 325° C. was 47 pct.

Jan 1, 1960

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By John O. Atkins

[Experiments were conducted by the Bureau of Mines on five types of simuated lunar rock (dacite, tholeiitic basalt, vesicular basalt, pumice, and uluth Gabbro) to study the effects of various simulated lunar environments n their strength and deformational properties. Specimens were tested in an ltrahigh vacuum (UHV) system at pressures ranging from atmospheric down to 0-11 torr and at temperatures of -130°, 20°, and 135° C. All tests were onducted with a servocontrolled testing machine. Rock specimens tested at 0° C in UHV exhibited significantly higher compressive strength and Young's odulus than those tested at 20° C in atmospheric pressure. The magnitudes f increase are related to the porosities and permeabilities of the rock pecimens; high porosity and permeability allow better outgassing and thus nprove surface cleanliness in UHV. The compressive strength generally ncreases but Young's modulus decreases as test environments change from 20° C i UHV to 135° C in UHV. No significant difference was observed in the iysical properties measured at 20° C in LTV and -130° C in UHV. Anisotropy i strength and Young's modulus exist both in UHV and at atmospheric condi¬'.ons with the same symmetry pattern. The orientations of the principal axes iy, however, change from the atmospheric to UHV condition. The results idicate that rock fragmentation in lunar environment will require more ergy than that at 20° C in atomospheric pressure.]

Jan 1, 1974

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By E. K. Stanek

This report contains the results of several related research efforts, all of which were aimed at enhancement of mine power system safety and reliability. The largest single effort was on optimum spares and maintenance scheduling for various components of a mine power system. Two closely related tasks involved calculation of the minimum arcing faults that could occur on dc trailing cables and the use of trippable load break switches to clear ground faults. Both of these tasks are concerned with reliable fault clearing to prevent shock and fire hazards. Three other closely related tasks were concerned with aspects of mine power system design: (1) alternate network topologies, (2) optimum voltage selection for mine power systems, and (3) selection of system components. The other research task consisted of laboratory tests to ascertain the effects of repetitive, low-level transients on insulation systems.

Jan 1, 1979

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936, and their rapid development have brought the problem of brine disposal to the foreground in that State. The ultimate magnitude of the problem is not yet known, but already it is treat enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field b brines in Illinois rend has studied in detail three subsurface disposal systems.]

Jan 1, 1940

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

By WILLIAM F. McMURRAY, James O. Lewis

The Bureau of Mines is investigating the technology of petroleum and its products, the investigation including well-drilling methods and the transportation, treatment, and utilization of petroleum and of natural gas, with especial reference to the prevention of waste and to increased efficiencyin the development of oil and gas resources in land belonging to or controlled by the Government. During. the winter of 1912-13 the enormous waste of the gas encountered while drilling for oil in the Cushing field, Oklahoma, called forth protests from various sources, and appeal was made to the President of the United States and to the Secretary of the Interior in behalf of the landowner and of the public in general. The facts were wanted regarding the amount of waste and the technical conditions that were responsible for practices causing it. An investigation was ordered and conducted under the direct supervision of the late J. A. Holmes, the first Director of the Bureau of Mines. R. S.Blatchley was sent to investigate the amount of waste going on in the Mid-Continent flelds.s In the latter part of March, 1913, J. A. Pollard and A. G. Heggem were sent to Oklahoma to study well-drilling methods with reference to the waste of gas from wells on Indian lands and to suggest means of preventing the waste of natural gas on such lands. Pollard and Heggem decided that the mud-laden fluid process, which had been used successfully for some years in Texas, Louisiana, and California was the method that would meet the situation most efficiently and economically. The method was accordingly demonstrated in Oklahoma. In 1914 Congress provided for the employment of six oil and gas inspectors to supervise oil and gas mining operations on lands of the Five Civilized Tribes in Oklahoma and to conduct investigations with a view to the prevention of waste. Positions under this appropriation have been held by William F. McMurray, James O. Lewis, Harry D. Aggers, Ralph R. "Weed,George W. McPherson, James C. Fowler, Louis W. Courtney, and Carl H. Beal, the technical work of these men being directed "byW. A. Williams, chief of the petroleum division, Bureau of Mines. After careful and impartial investigation of conditions in Oklahoma, these men also decided that the mud-laden fluid process was the one best adapted to prevent further wastes. In 1915 laws were passed by the State of Oklahoma that provide for the conservation of natural gas and oil, authority being given to the corporation commission to make rules and regulations and to employ agents to enforce them. After hearings and investigations, the corporation commission reached substantially the same conclusions as the Federal agents regarding the importance of the wastes and the best methods of conserving the gas. Technical Papers 66a and 68b were published by the Bureau of Mines in December, 1913, and January, 1914, respectively. Technical Paper 66 deals with the mud-laden fluid process in general and No. 68 with its application in Oklahoma. The interest aroused by these publications has been so widespread that within two years the first editions have been practically exhausted. Rather than reprint these publications, it has been considered advisable to replace them with the present report, which includes the results of more recent investigations. The methods of using the mud-laden fluid are an outgrowth of the rotary drilling system, which was developed in Texas and later employed in Louisiana and California. Some of the principles of the use of mud fluid had been observed and used to a limited extent for a long time in cable-tool drilling. So far as known it was first used successfully with a circulator and cable tools in the Coalinga field, California, in 1906,Harry D. Aggers, one of the contributors to this paper, working on the well. The part of the Bureau of Mines has been to call attention to its merits and to demonstrate its practical use in fields like those of the Mid-Continent.

Jan 1, 1916

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By E. P. Carman

This report is the 19th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The first 17 reports covered fiscal years; however, the 18th report3/ covered the 18 months from July 1, 1952, to December 31, 1953, to permit the publication of this and subsequent reports on a calendar-year basis. Most of the material in this report relates to publications by Bureau authors issued during the reporting period. Some work is referred to on which the results have not yet been published or may not be published for security or other reasons. In a few instances publications are mentioned that were issued before the reporting period but were not included in previous reports. Further details on the published work described herein may be found in the publications cited in the footnotes. Research and technologic work on coal by the Bureau is directed toward developing and encouraging increased conservation of coal resources through safer and more efficient mining, preparation, and utilization. Significant advances were made during the year in these fields, particularly in coal-mine safety and in preparation and utilization of the various ranks of coals.

Jan 1, 1956