Search Documents

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By P. W. Jeran

The Stereonet Analysis Program (SNAP) is a mathematics tool which, by means of a computer, reproduces mathematically the manual techniques of pre- paring stereograms. This computer program was developed to provide a fast, accurate, and economical means of analyzing fracture orientation data. It is mitten in FORTRAN IV for use on a UNIVAC 1108 operating under an Exec II system, but can be adapted to other systems. SNAP is currently being used to aid in the analysis of cleats and other geologically induced fractures associated with coalbeds that are being mined underground, Methane flows through the coalbed and into these mine workings predominantly through the fracture system. Therefore, knowledge of fracture orientation is an invaluable aid in the development of methane control technology.

Jan 1, 1970

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

This Information Circular describes the Bureau of Mines Minerals Availability System (MAS), presents the Resource Classification Manual used for information input to a computer file, and discusses the methods of collecting and assembling background material' basic to coding the data.

Jan 1, 1974

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By George S. Rice

This bulletin traces the growth in the belief in the explosibility of coal dust, summarizes the experiments and mine investigations that have established this belief, and gives the present status of pre- ventive measures. It has been prepared in accordance with the pro- visions of the acts of Congress authorizing investigations relating to the causes of mine explosions, and contains references to and descrip- tions of experiments made at the Federal testing station at Pittsburg, Pa. This station was inaugurated under the United States Geo- logical Survey, and was transferred to the Bureau of Mines on the establishment of the latter on July 1, 1910. Only within comparatively few years has the dry dust of bitumi- nous and lignitic coals been generally recognized as an explosive agent more insidious, threatening, and deadly to the miner than fire damp. Fire damp carries its own flag of warning-the "cap" in the safety lamp-but coal dust, though visible, does not attract attention until present in large quantities. Fire damp is of local occurrence, and except in notable and very exceptional cases is controllable by careful manipulation of ventilating currents. If by mischance a body of fire damp is ignited in a mine, the force of the explosion may be terrific, but the effect is local unless dry coal dust is present, or unless (as it very rarely happens) an explosible mixture of methane gas and air extends through large areas of the mine. In a dry mine dust accu- mulates everywhere, and the blast from the ignition and combustion of bituminous dust may traverse miles of rooms and entries and wreck structures at the entrance to the mine. The comparative potential destructiveness of gas and of bituminous dust is strikingly shown by the history of the Pennsylvania anthracite mines. These mines not infrequently have large inflows of gas, and the resulting mixtures of gas and air have sometimes been ignited, yet no such wide-sweeping explosions have taken place, despite the presence of dry anthracite dust, as have happened in excellently ventilated bituminous mines.

Jan 1, 1911

By G. E. McElory

"INTRODUCTION The subject of mine and tunnel ventilation has two broad aspects - (1) what atmospheric conditions to obtain in underground openings and (2) how to maintain the desired conditions efficiently. The first relates primarily to quantity requirements of ventilating systems, whereas the second relates more particularly to pressure requirements. Both, therefore, determine power requirements, which is the deciding factor in any system of mine or tunnel ventilation.Both divisions of the subject have received considerable attention from the Bureau of Mines since its inception in 1910 in the form of research, service, and correlation and dissemination of information. Numerous papers on various Phases of the subject have been published, of which a selected list, numbered and arranged in chronological order by type of publication, will be found at the end of this Paper. One of these, Technical Paper 705 (25) 2/ gives a complete bibliography of Bureau of Mines publications dealing with health and safety. As indicated by the selected list of publications accompanying this paper, the health and safety aspects have received most of the attention devoted to this work, chiefly because these have been dominant factors in Bureau policy, but partly because these aspects lend themselves to laboratory research and small-scale field studies. Although considerable attention has also been devoted to the engineering aspects of mine and tunnel ventilation, there has been, in the opinion of the author, who has been engaged on this phase almost continuously for the last 30 years, only sporadic recognition of the vital effect this phase of the work could have on improving health and safety conditions. As a matter of fact, ventilation activities have constituted but a very minor part of the total work of the Bureau of Mines, as, except for a few years in the nineteen twenties, there have been only a few short intervals when more than two or three men were engaged in field work and a similar number in laboratory research directly related to mine gases or mine air."

Mar 1, 1950

By A. S. Swanson

The Babb fault vein in Crittenden and Livingston Counties, Ky. (fig. 1), is one of an extensive series of such veins in the Western Kentucky and Southern Illinois fluorspar district. First operated in 1904, the production to May 1, 1944, was estimated at 143,000 tons of fluorite ore. There are five mines (fig. 2) on the Babb fault zone - Guill ,Kentucky Babb, Delhi-Babb, Eagle-Babb and Howard-Barnes. The Bureau of Mines developed four of these properties by core drilling from July 9, 1943, to May 1, 1944. During that period a total of 8,177.8 feet of diamond drilling was completed in 28 holes.

Jan 1, 1950

By A. W. Fahrenwald

Many factors enter into the efficient operation of the reciprocating type of gravity concentrator. Earlier investigators who studied these factor invariably used natural (crushed ore) products for their experiments, but in the present study synthetic products were used. The variables considered were (1) specific gravity of the sand grains, (2) size of sand drains, and (3) shape of sand grains comprising the table feeds. It is recognized, also, that the percentage relationship of the different kinds of grains is a factor affecting results. This factor is variable in one group of experiments but is thereafter kept constant.

Jan 1, 1929

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In with this request a preliminary review has been made of trends in the production and uses of block granite.. Some unfavorable conditions were thus brought to light, and certain suggestions regarding a more orderly and consistent growth in the industry are herein discussed. The results of the study are, presented in this report for the earnest consideration of. the industry, and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of Mines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable assistance through her wide knowledge of granite statistics. The block granite industry has shown little expansion during recent years. While the value of the annual production has grown from about $14,000,000 in 1904 to nearly $25,000,000 in 1928, the increment in value is caused mainly by mounting prices rather than by increased production. Even granite for memorials shows a very small advance in production volume, although the value has increased from about $3,500,060 in 1904 to more than $11,000,000 in 1928, which is the most consistent growth of any branch of the industry. The value of building granite has fallen for a number of years much below the figure for 1904, and in 1928 was very little in advance of the value attained 24 years previously. The use of granite paving blocks and rubble has shown a gradual decline.

Jan 1, 1931

By Forest H. Majors

"INTRODUCTION The Brutch sulfur deposits were explored by the Bureau of Mines during the spring and summer of 1944. Old workings were rehabilitated and sampled, test pits and shafts were sunk, and trenches were cut through the surface alluvium.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due S. R. Zimmerley, regional engineer, and Paul T. Allman, principal engineer, Bureau of Mines, Salt Lake City, for their supervisory aid, and to the metallurgical staff, Salt Lake City, for beneficiation of samples."

Oct 1, 1946

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By William H. King

The Mining Division of the Bureau of Mines has been making development and power-requirement studios for the Interior Department Missouri Basin Field. Committee. The studies by the Bureau of Mines have as their purpose, the summarizing of potential future power requirements in the mineral industry within the Missouri Basin, special emphasis being placed on possible expansion of these requirements through construction of new mining enterprises by private capital. In preparing a proposal for the production of phosphoric acid from phosphate rock near Lander, Wyo., it was found that the basic information on the physical and chemical characteristics of the phosphate beds to determine costs of mining and treatment was lacking.

Jan 1, 1949

By T. M. Barczak

The term "resultant load vector" is defined as the representation of the forces applied to a longwall roof support element by strata activity through a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield structure prohibits determination of support resistance simply from the summation of leg forces. In the research reported in this Bureau of Mines study, the mechanics of the shield structure were evaluated, and a technique was developed whereby the resultant shield loading could be determined by instrumenting supports with pressure transducers and strain gauges to measure leg, canopy capsule, and lemniscate link forces. This technique has been laboratory tested in the Bureau's Mine Roof Simulator. Functional relationships among variables were assessed, and confidence intervals were established for prediction of the resultant load vector parameters. Resultant load measurements were taken on five instrumented shields on an active longwall face in Colorado. Results were analyzed and found to be consistent with shield mechanics and anticipated roof behavior. Benefits to be derived from this research, future efforts, and long-range goals are discussed.

Jan 1, 1986