Search Documents

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

By R. V. Lundquist, A. E. Morris, E. L. Singleton

This experimental research was performed to determine rate - of - reaction constants on the MnO - C and Mn , C₂ - 3MnO systems at 1,100 ° , 1,150 ° , and 1,185 ° C. Reactions were conducted at atmospheric pressure under controlled flow of purified helium through the furnace chamber . The weight - loss method defined reduction percentages , and reaction products were identified by X- ray methods . The system Mn0 - C followed a linear reaction rate , and experimental results produced an apparent activation energy of 55.8 kcal per mole of Mn0 . The system Mn, C - 3Mn0 followed a parabolic rate of reaction law and yielded an apparent activation energy of 114.4 kcal per mole for the reaction .

Jan 1, 1964

By C. A. Komar

The Bureau of Mines conducted experiments on one synthetic and three natural sandstone samples to investigate the effects of acoustic energy on the flow of brine in porous media. Ultrasonic energy at a frequency of 20 kc per second and an intensity of 55 watts per cm2 was irradiated in the direction of the fluid flow and in the opposite direction for distances of 1/2 and 2 inches between the vibrating device and the sample face and under conditions of suppressed and nonsuppressed cavitation. Forty tests were conducted: 32 with a pressure differential of 0.64 psi across the samples, 2 with 5 psi, and 6 with 15 psi. Acoustic waves altered the rate of flow of the brine through the samples, but this effect was observed only at low differential pressures and from a practical point of view was insignificant. As a result of irradiation, however, the samples exhibited reduced permeability. This reduction was probably caused by the shifting of solid particles dislodged by the acoustic waves.

Jan 1, 1967

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1985 was $405.9 million, a slight decrease from the record high of 1984. With the exception of clays, output of most nonfuel minerals increased over that of 1984. Alabama was second in the Nation in production of crushed marble and bauxite; third in firre clay; fourth in masonry cement and kaolin; fifth in portland cement and lime; and sixth in ferroalloys and recovered sulfur, Alabama ranked 20th in the Nation in value of nonfuel minerals produced, but ranked 13th in value of industrial minerals. Valuewise, Alabama produced 2.4% of the Nation's industrial minerals.

Jan 1, 1987

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By Thomas R. Bur

This method of performing general transformations by use of Eulerian angles greatly reduces the time required for the determination of values for the elastic compliance constants (sij), elastic stiffness constants (cij ), Young's modulus, shear modulus, or Poisson's ratio for any orientation the cartesian coordinate system in an anisotropic material.

Jan 1, 1969

By Victor E. Kral

The Valery fluorspar deposit , also known as the Hamilton deposit , is northeast of Lovelock and 4 miles by poor dirt road east of U. S. Highway 40 . It is in the Humboldt Mining District , on the west side of the Humboldt Range , at an altitude of 6,000 to 6,500 feet . The property was examined by the Bureau of Mines on February 83/ and April 8 , 1944.4/ The last examination was made with an engineer of the Geological Survey.5/ Exploring by means of trenches , cuts , shaft sinking , coyote holes off the shaft , and a small amount of prospecting with short drill holes , was begun in January 1945 and was completed June 30 , 1945. An engineer6/ of the Geological Survey visited the property in April and again in June 1945 to complete a topographic map of the area and to note the results of exploration by the Bureau of Mines . Only minor surface exploring had been done on fluorspar occurrences previous to the Bureau's work . No mining equipment or living facilities are on the property .

Feb 1, 1947

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By J. F. Barkley

At the request of several Federal agencies, tests were conducted on a relatively recent type of anthracite -burning equipment named the Anthratube. This device, rated at 130,000 B.t .u. per hour, was designed to burn Pea-size anthracite automatically for steam or hot-water house heating and for domes-tic hot -water supply. ACKNOWLEDGMENTS The helpful cooperation of the Anthracite Institute and the manufacturers of the equipment, Axeman-Anderson Co., Williamsport, Pa., is gratefully acknowledged.

Jan 1, 1953

By S. J. Pearce

There are a number of methods for determining relatively small quantities of sulfur dioxide in air. However, those methods require fairly elaborate apparatus and laboratory facilities. Frequently in industrial hygiene surveys it is desirable to have a simple arrangement to obtain "on the spot" determinations. This has been accomplished for concentrations of sulfur dioxide of hygienic significance by using the midget impinger and decolorizing a starch-iodine solution.

Jan 1, 1948

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Douglas Deposit in an attempt to find an additional source of supply of copper. The deposit, which was opened in 1878, was worked until 1883 and is reported to have produced between 2 and 3 million pounds of copper. Heap-roasting and smelting and later gravity concentration were employed in ore reduction. Old slag dumps and tailing piles from these operations still remain. In 1917, the American Smelting & Refining Co., purchased the mine, and in June 1918 production was started in a 125-ton mill, using both tables and flotation. The mill was closed December 31, 1918, and soon after the milling plant Was dismantled and removed. The mine has remained idle ever since. The deposit occurs in a mineralized zone that follows the schistosity. The principal metallic minerals are pyrite) chalcopyrite, pyrrhotite) arsenopyrite, sphalerite, magnetite) slight chalcocitel and cuprite. To search for additional ore shoots and to prove the known ore shoot at depth, the Bureau of Mines drilled seven holes, which totaled 2,117.4 feet. No additional ore was developed by this work.

Jan 1, 1950

By Robert L. Grayson, Syd S. Peng

"An airborne dust study was undertaken at a Southwestern Pennsylvania underground bituminous coal mine by the Pennsylvania Department of Mines and Mineral Industries in 1964 for the purpose of making recommendations and requirements regarding compliance with health and safety aspects of The Bituminous Coal Mining Laws of Pennsylvania, approved by the legislature on July 17, 1961. The study was designed to accurately represent the airborne dust conditions of the subject mine. Sampling by midget impinger of specific worker locations throughout the mine was accomplished. Sample analyses yielded dust concentrations to mppcf, particle size determinations in cumulative per cent less than specified cut-off diameters, and determinations of free silica percentages in total dust samples. The data from this study is further analyzed, and the results are presented.INTRODUCTIONThe Bituminous Coal Mining Laws of Pennsylvania, enacted in 1961, prompted a study of respirable coal mine dust by the Department of Mines and Minerals Industry in 1964. In recognition of their obligation for ensuring the health and safety of bituminous coal miners, the department set out to characterize the airborne dust of mines throughout the commonwealth. The purpose of the studies was to make recommendations and requirements for compliance with the law and for control of airborne coal mine dust in Pennsylvania mines.One such study was undertaken at an underground bituminous coal mine operating in the Pittsburgh Seam in Southwestern Pennsylvania. The study was desig11ed to sample specific worker locations throughout the mine site and characterize the respirable dust relative to each of them. A midget impinger was used to gather respirable range dust samples during an 8-hour shift. Continuous miner operator, roof bolter, stoper bolter, loading machine operator, shuttle car operator, gathering motorman, mainline motorman, and rotary dumper jobs were sampled underground. In addition, barge mover, coal sampler, fine coal operator, heavy media operator, and boiler room attendant occupations were sampled on the surface. The surface sampling was over a 71-hour shift because of UMWA contract provisions."

Jan 1, 1988