Search Documents

By Robinson Newcomb

Gypsum is a form of hydrated calcium sulfate (CaS04.2H20) which is widely distributed over the earth's surface. The two varieties worked commercially are rock gypsum and incite. Rock gypsum, the variety commonly mined for commercial purposes, is a relatively soft mineral having a specific gravity of about 2.3 and weighing about 150 pounds per cubic foot. The chief producing States are New York, Michigan, and Iowa. Before being used the crude gypsum is ground and generally calcined. The predominant use of gypsum is for building purposes (the manufacture of plaster), for which calcined gypsum is required. Gypsum is also used as a retarder in Portland cement, as fertilizer, and for other purposes. GYPSUM MINING Crude gypsum is mined by two methods - underground and open-pit. Although the use of the former method predominates, open-pit mining increased in relative importance during the early twenties and contributed about two-fifths of the output during the period 1925-38.

Jan 1, 1940

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By J. Alton Burks

When acoustical materials are used in a mining environment for noise control purposes, they are subject to environmental deterioration from hydraulic fluid, moisture, and dust. These and other factors can cause physical degradation of the material, which can lessen its ability to absorb sound. In this study, the Bureau of Mines measured the sound absorption properties of 16 different acoustical materials after 4 sample treatments: (1) being kept clean and dry (as received from the supplier), as a control or reference standard, (2) immersion in water and draining, (3) immersion in lOO-pct-petroleum-type hydraulic fluid and draining, and (4) exposure in a coal mine. The last three treatments were used to approximate the type of physical degradation that can be experienced in actual use. The impedance tube or standing wave method was used to measure the normal absorption coefficient. It was found that the absorption coefficient of most materials was adversely affected by the retention of either oil or water, with oil having the greater effect. The only class of materials that was affected by neither oil nor water was neoprene foam.

Jan 1, 1990

By C. H. Fisher

[Many methods of analyzing tar oils for their tar acid and base content have bun employed in connection with both academic and. industrial investigations. Most of these analytical procedures are based on the diminution in volume caused by extraction with alkali and mineral acids (contraction method), although other methods haves been employed.4/ In many instances the adoption of an analytical method was not preceded by adequate study, and, as a consequence, the literature, on this subject is conspicuous for its contradictory claims and recommendations. It has bin shown in the, case of certain synthetic solutions5/ that large errors may result if the analysis is carried out by simple extraction with alkali and mineral acids.]

Jan 1, 1936

By Ralph Husack

The Bureau of Mines investigated the effect of gamma radiation on reactions between Pennsylvania anthracite and fluorine and chlorine. In the tests with fluorine about 90 percent of the coal reacted at 350° C to form volatile products whether or not irradiation was employed. Up to 0.8 ml of liquid products per gram of anthracite was collected. Among the 25 com-pounds indicated by gas chromatography, fluoroform and l,l-difluoroethylene were tentatively identified from their relative retention times and perfluoro-cyclopentane from its infrared spectrum. In addition, a clear, hard, wax, probably a fluorocarbon, was formed at 45° C in both the presence and absence of radiation. With chlorine there was no significant difference due to radiation, and preliminary tests indicated that the chlorine reacted more with the organic matter of anthracite at 200° C than with inorganic matter. At 400° C the results were inconclusive because of excessive corrosion in the reaction vessel.

Jan 1, 1966

By Roger L. Williams

The Bureau of Mines investigated northern New Jersey as a potential future source of yttrium and the rare-earth elements. The studies, consisting of geophysical surveying, sampling, and exploratory drilling, began in the spring of 1959. A total of three and one-half months were spent in the field collecting data. Thirty-three deposits were investigated, of which five demonstrated some potential resources of yttrium and rare-earth minerals. Results indicate that the deposits examined do not contain quantities of yttrium and the rare-earth elements recoverable under present economic conditions. Detailed studies conducted at the Scrub Oaks mine, near Dover, N. J., delineated a yttrium and rare-earth-bearing zone within the magnetite-hematite ore body that represents a potential low-grade deposit. Beneficiation studies on this deposit indicate that a final product, averaging 31.3 percent rare-earth oxides including yttrium, could be produced through amine and fatty acid flotation procedures with 77 percent recovery. Two hundred and eighty-five feet of diamond drill core was obtained from exploration studies conducted at the Bemco prospect in Sussex County. The deposit averages 2.30 percent rare-earth oxides (including yttrium), 0.45 percent uranium and 0.24 percent thorium. Low-grade deposits were identified at the Canfield phosphat2 mine and the Tanners Brook Monazite placers in Morris County, and the Marble Mountain prospect in Warren County.

Jan 1, 1967

By D. E. Wolfson

Twenty-two samples of West Virginia coals were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Eighteen samples represented the Coa1burg, No. 2 Gas, No. 2 Gas and Peerless, Powellton, Eagle, Big Eagle, Lower Eagle, Sewell, Fire Creek, and Pocahontas No.6 beds in Fayette County, and four samples represented the Sewell and Fire Creek beds in Greenbrier County. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses were determined for all coals. The coals in Fayette County are high-volatile A, medium-volatile, and low-volatile in rank, and the Greenbrier coals are medium-volatile in rank. Most of the coals are chemically suitable for metallurgical coking. All coke strength indices are within acceptable limits for metallurgical coking coals. All the high-volatile A coals contracted and the medium-and low-volatile coals expanded in the sole-heated oven expansion test.

Jan 1, 1966

By Andrew Brown

"In recent years operators of brown-ore mines have shown increasing interest in .the reclamation of ore heretofore lost in tailing ponds. In January and February.1945 the author made a preliminary survey of the ponds in the Russellville district, Franklin County, Ala. The Russellville district (fig. 1) was chosen for the preliminary work because it contains many large ponds in a comparatively restricted area. All important properties in the district were visited with Charles R. Wilson of Russellville, who has been familiar with the Franklin County brown-ore industry since 1890; with Edmund Craddock and W. S. Blackburn, managers of the two washers now operated near Russellville by Shook & Fletcher Supply Co., and with S. A. Britton, manager of the Sloss-Sheffield Steel & Iron Co. washer. The larger ponds were measured roughly and tonnages estimated. and samples taken from different areas were analyzed and beneficiated at the Southern Experiment Station of the Bureau of Mines; Tuscaloosa, Ala.The ponds explored were the Sloss No.1 (Ensley); the Sloss No. 8, and the Sloss No. 4-5, which are among the largest in the district and so located, within an area of .three square miles (see fig. 2), that ore from all of them could be-treated,one centrally located washer.Actual work was begun on May 9. Between that date and June 30, when field work was completed, 246 holes in ponds were drilled and sampled, and 15 additional holes were put down primarily to test the drill .in different types of ground with a view to its possible utilization in other types of prospecting. Samples from all holes were analyzed for iron content; samples from 13 holes were sized and analyses made for each size fraction, and six large samples have been composited for beneficiation tests.Brown iron ore has been mined in the Russellville district since 1815, when the first blast furnace in Alabama was built in NW1/4 sec. 10, T. 7 S., R. 12 W., about 3 miles southwest of Russellville (19).-J The furnace was abandoned before the Civil War, and mining continued on a small scale until 1888, when Enoch Ensley began to mine the ridge between Russellville and Pain Creek. His first washer, Ensley No. 1, was about 300 feet south of the junction of the present Tharptown road with the Waco spur of the Southern Railway."

Aug 1, 1946

By J. P. BONARDI, J. C. Williams

Until the end of 1918 Boulder County ranked as one of the foremost tungsten-producing districts of the world, but in August, 1919, there was practically no production in the district. The operators there could not compete with tungsten ores from foreign sources, particularly China, Burma, and South America. As a. result there · has been a strong movement for placing a protective tariff on all imported tungsten ores and products; and it seems to be the general belief of tungsten producers that some form of protection is necessary to the maintenance of the industry in this country. The stimulus, due to the great demand for · tungsten alloys in the manufacture of munitions during the war, was felt in all the productive localities of the world. The ores of Boulder County were especially in demand on account of their comparative. freedom from • harmful impurities, and this demand greatly extended mining operations in the district and increased the efficiency of the gen~ral milling practice there.

Jan 1, 1921

By Charles W. Perdue

This U.S. Bureau of Mines report considers, from a psychological perspective, the perceptual process by which miners recognize and respond to mining hazards. It proposes that if the hazard recognition skills of miners can be improved, mining accidents may be reduced to a significant degree. Prior studies of hazard perception in mining are considered, as are relevant studies from investigations of military target identification, pilot and gunnery officer training, transportation safety, automobile operator behavior, research into sensory functioning and visual information processing. A general model of perception is introduced, and selected concepts from the psychology of perception that are applicable to the detection of mining hazards are reviewed. Hazard recognition is discussed as a function of the perceptual cues available to the miner as well as the cognitive resources and strategies employed by the miner. The development of expertise in responding to hazards is related to individual differences in the experience, aptitude, and personality of the worker. Potential applications to miner safety and training are presented.

Jan 1, 1995

By G. W. Jones, F. E. Scott

"INTRODUCTION As a part of its program of promoting safety in mining and other industries, the Bureau of Mines investigates the explosion hazards of combustible Gases, vapors, and solids. It also investigates various means and methods of controlling and mitigating explosions.Dichlorodifluoromethane, CC12F2, has been found to be very efficient as a quenching agent for methane flames. 4/ This substance is a gas at ordinary temperatures and pressures and is relatively nontoxic and stable at mod rate temperatures.Tremendous quantities of dichlorodifluoromethane were used daring the late war as an expelling agent for aerosol mixtures in ""aerosol bombs."" At one time during the war the demand for Dichlorodifluoromethane became so gent that there was barely enough of it to supply the Army and Navy and virtually none for civilian needs. During this period of scarcity the Bureau of Mines, in cooperation with the Bureau of Entomology, Department of Agriculture, investigated the possibility of substituting other materials in part for the dichlorodifluoromethane. It was required that the resulting mixtures be satisfactory expellant and noninflammable under all normal conditions of use."

Jun 1, 1946

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations, of which this is the seventh. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in , this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of .1 minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Lloyd Williams

1. This investigation shows that the Sewanee bed is the only coal bed being mined in Sequatchie County. Other coal beds are present, but as they do not contain known recoverable reserves, estimates of reserves were made only for the Sewanee bed. 2. Known measured and indicated reserves in the Sewanee bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 76 million short tons as of January 1, 1953. Of this total 62 million short tons represent coal 28 inches and more thick. Areas in the bed were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1955

By J. B. Ligon

Blast induced stress waves, propagating along the surface of a drift of an underground hardrock mine, were recorded and analyzed. Resistance strain gages, accelerometers and a velocity pickup were used in making the measurements. Although a full face blast was recorded, the stress waves were initiated by single borehole blasts for the majority of the project. A special instrument trailer was designed, constructed and utilized during the project. A reliable strain wave transducer was developed for measuring the stress waves propagating on the drift surface. A correlation study between strain and acceleration signals for P-waves was made which agreed well with theory. The use of stemming was found to reduce strain and acceleration magnitudes as predicted.

Jan 1, 2011

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By Frederick L. Hoffman

These extracts are sufficient for the purpose of emphasizing the practical difficulties of averaging iron-mining conditions so as to make general vital statistics concerning iron miners useful Tor scientific. purposes. It is self-evident that conclusions based upon iron miners, so called, working largely above ground and employed chiefly in open-cut blasting ~perations or the management of steam shovels, etc., can not be made to apply to miners working continuously underground with an exposure of dust and other conditions quite similar to underground mining methods in the extraction of gold, silver, copper, lead, and other ores. The so-called "milling" process as practiced on the Mesabi Range may here be referred to, the same being explained in the report of the Immigration Commission to consist "in the sinking of a shaft on the edge of the ore body from which a tunnel is run in under the ore and connected with a vertical, funnel-shaped hole from under the surface, through which the ore is 'milled' down into the tramcars placed under the opening under the tunnel. After being loaded at the bottom of the funnelshaped hole, the cars are run out to the bottom 0.£ the shaft. where the ore is dumped into skids or elevators and raised to the ~urface and unloaded into the tipple, where it is loaded into thecal'S ready for shipment." It is properly pointed out that the so-called " milling" process employs some of the features of both the open-pit and underground methods of mining. For these and many other reasons it is self-evident that general statistics concerning iron mining are quite likely to be inconclusive and possibly seriously misleading. Aside from the foregoing the problem is seriously complicated by the extensive employment of foreign labor in the iron-mining ind ustries of the Lake Superior districts and of Negro labor in iron mining in Alabama. Within recent years, according to the report of the Immigration Commission, a considerable displacement has occurred in t~e quality of labor employed in iron mining, the displacement bemg referred to as "progressive," in that one race or group of races has entered the region and taken up the work offered in the lower occupations, the race or races already holdinz such positions having. moved up in the scale of occupation leaving the field to the newcomers. This statement is quite suggestive in that it indicates a comparatively short average trade life or trade exposure, quite at variance with the relatively long average ascer- MINES, QUARRIES, ORE REDUCTION, AND SMELTING. 377 tained for the iron mines of New <Tersey. It is said in the report of the Immigration Commission that- The Scandinavians and the other northern European races have given way to the Finns and Slovenians, and in the open-pit mines the Finns and Slovenians have given way to the south Italian, Montenegrins, Croatins, and other southern European races. In the underground mines the common labor and mining is chiefly done bv Finns and Slovenians because the races from the southern countries can not stand the heavy physical work required in this kind of mining. Here, too, is found the same upward movement, for formerly the English (Cornishmen) and Scandinavians' were in the lower occupations in the underground properties, At present the south Italians, Serbians, Montenegrins, and Croatians are performing the most menial work and are the races who are now at the foot of the scale of occupations. It is a matter of conjecture on the ranges as to who will push these races up or whether they will remain the commou laborers of the region. Inquiry was made into the prevalence of diseases OIl the ranges, but more with reference to outside sanitary conditions than to occupational exposure. The most common diseases on the ranges, however, were ascertained to be pulmonary tuberculosis and typhoid fever, and to a lesser extent smallpox and venereal diseases. With -cgard to pulmonary tuberculosis it is said that the disease is most Eevalent among the Finns and the Swedes, and is chiefly imported, I'here is no reference to a possible connection between disease occur- ~ence and occupational conditions, above or below ground, but there .s no evidence that this aspect of the iron-mining industry was made .he subject of a special investigation.

Jan 1, 1918

By Guy B. Taylor, Horace C. Porter, E. C. White

When the Federal investigation of coal - dust explosions in mines was begun in 1908 , following a series of mine explosion disasters in 1907 , mining men generally questioned whether coal dust in air is explosive unless " gas " or methane is present , though perhaps in small amounts not detectable by a safety lamp . The experimental tests beginning in 1909 at the Pittsburgh testing gallery, and after 1911 , at the Experimental mine , demonstrated to the mining public the explosibility of coal dust in itself . There followed much controversy , both among practical mining men and scientists , as to whether the coal-dust particles uni te directly with the oxygen of the air, or whether gas is instantaneously distilled from the dust prior to explosive combustion , the gas enveloping each particle and propagating the flame from one to another . In considering methods of preventing explosions , this question made no difference for practical purposes , but it did have bearing in determining the relative inflammability of dusts of different coals . This led to the experiments by Guy B. Taylor and Horace C. Porter , on the momentary heating of the inflammable coal dusts , reported in this paper . Meanwhile , experiments on the inflammability of coal dust conducted in the Experimental mine , under my direction , and in the laboratory by J. C. W. Frazer and later by J. K. Clement and J. N. Lawrence , showed that different kinds of coal dust differ markedly in inflammability , thus confirming experiments made by Messrs . Taffanel and Durr at the Lievin Testing Station , France , and by various investigators in Great Britain . Both the French and British investigators concluded that their experiments demonstrated the distillation of volatile matter preceding inflammation .

Jan 1, 1922