Search Documents

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By Lawrence G. Houk

Monazite sand is the only commercial source of cerium, other rare-earth metals and thorium. Although used in rather small quantities, it is essential to many industries. The United Unites is entirely dependent upon British India and Brazil for its supplies. Monazite sand or sand imported under the tariff classification for monazite was shipped to the United States in greater quantities, in 1940 than ever before. About 75 percent of our imports was from British India and most of the remainder from Brazil. If need be, Brazilian production can be expanded to supply all of our essential requirements, and the theater of war expands in the Pacific Brazil may supersede India as the principal source. PHYSICAL PROPERTIES The mineral monazite is generally honey yellow or may vary from greenish yellow to clove brown. The grains are small and resinous in luster, and range from subtranslucent to opaque. The specific gravity varies

Jan 1, 1943

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By R. L. Grant

The principal official test performed by the Bureau of Mines to determine the permissibility of coal-mine explosives, commonly referred to as the gallery test, has been in use at the Bruceton station for many years (2, 16).4/ In this test the explosive under study is loaded into the borehole of a steel cannon and fired into a flammable mixture of natural gas and air or natural gas, air, and coal dust. To meet the requirements for permissibility, the explosive must not ignite the gas mixture under the conditions of the test. There is little doubt that these tests have succeeded in the main objective, namely, to screen the relatively safe from the relatively hazardous explosives. It has been generally conceded that adoption of permissible explosives by the coal-mining industry in the United States has substantially reduced the frequency of disastrous underground explosions caused by blasting. In recent years, however, research workers planning programs for improving the safety of coal-mine explosives have felt the growing need of a more quantitative method for measuring the incendivity of explosives based on a better understanding of the role of the important variables in the gallery tests, Accordingly, it was decided to apply certain statistical methods and techniques to the gallery test to develop it into a more precise tool for evaluating permissible explosives. One of the first and more important methods applied for this purpose was the up-and-down technique (6,7,17), It was demonstrated (14,15) that the weight of the explosive charge directly affects the ignition probability of the natural gas-air atmosphere and that the curve of ignition probability versus charge weight is a cumulative normal curve. Following these experiments, a program, still in progress, was set up to study how the addition of sodium chloride to various permissible-type ex-plosives affects their incendivity. This program resulted in 3,294 shots,

Jan 1, 1961

By Joseph D. Davis, G. S. Scott, Palmer B. Place

In the course of investigations made by the Bureau of Mines in cooperation with the Trent Process Corporation, into the properties of mixtures of oil and coal, a comparative study was ma.de of the 'behavior of these mixtures and their cons ti tuents on destructive distillation. Mixtures of a petroleum oil and bitminous coal were first distilled under carefully controlled conditions, and then charges of the eame oil and coal were distilled separately under similar conditions. The quantity and quality of the distillation products were determined, and. resul. ts were compared. This comparison furnished a basis tor judging whether grea, ... er values in products can be obtained by distillation of oil and coal in mixtures than· b:, their separate distillation. In making the mixtures, the method used in t~e Trent process for cleaning coal was followed. The paste or plastic emulsion of oil and coal obtained is called "amalgam".••• When finely pulverized wet coal is mixed with approximately one-third its weight of. oil and agitated with a large excass of waj;er, the coal and oil agglomer-. ate to form a paste or amalgam. A large portion of the extraneous ash original.17 in the coal remains suspended in the water, with which it can be decanted from the amalgam. Ir the latter is now thoroughly drained and kneaded after the manner ot working butter, most of the excess water enclosed can be removed. This, .in brief, constitutes the Trent process for cleaning coal, The effectiveness of the process for cleaning coal has been studied••••. by the Bureau, and the results of the study show, in general, a high ash reduction an:l good recovery of combus ti bl e f'rom coals of medi ,mi and hi~ rg,nk. With coals of tht lowest rank, such as li@!Rlites, the process is only moderately auccessf'ul, owing to the difficulty attending the preparation of coherent amalgams, Oil losses to wate~ and refuse are small, and apparently it would be practical to rotate the same oil in the cleaning process if some efficient method were devised for recovering it from the amalgam, so a distillation process naturally suggested itself.

Dec 1, 1921

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By Irving Hartmann

The Experimental Coal Mine of the Bureau of Mines has served principally as a valuable and unique testing laboratory for studies of the explosibility of coal dust and mine gas; studies of the numerous complex and interrelated chemical and physical factors that govern the ignition of coal dust and the propagation of mine explosions; and studies designed to develop measures for preventing explosions or reducing their destructive effects. These researches, coupled with educational efforts by the Bureau of Mines and enlightened safety consciousness in the mining industry, had fruitful results. This is evidenced by the remarkable reduction in the frequency of major coal-mine explosions and the number of fatalities from explosions since the Bureau of Mines was established. Despite this progress, further important unresolved problems arise; these are due in part to changes in mining conditions and methods, which have brought about increased production of fine coal dust in highly mechanized operations. To solve the new problems, research must be continued without interruption. The results of many very recent and current studies in the Experimental Coal Mine are summarized briefly, and pertinent studies by European mine-safety-research organizations are listed.

Jan 1, 1957

Minerals are a fundamental component of the Nation" material and economic base. Without a continuous supply of minerals to meet growing and changing needs, the basic character of our society would be very different. The importance of minerals to the United States was reemphasized by the Congress in I970 when it enacted the Mining and Minerals Policy Act, which stated that it is the continuing policy of the Federal Government in the national interest to foster and encourage private enterprise in (I) the development of economically sound and stable domestic mining, minerals, metal and mineral reclamation industries, (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial, security and environmental needs, (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral recources, and (4) the study and development of methods for the disposal, control, and reclamation of mineral waste products, and the reclamation of mined land, so as to lessen any adverse impact of mineral extraction and processing upon the physical environment that may result from mining or mineral activities.,.

Jan 1, 1977

By D. R. Mathews

Electrorefined vanadium was evaluated with respect to tensile properties and the effects of interstitial contaminants in the temperature range of 77° to 273° K. The yield strength of 18,500 psi and hardness of 63 diamond pyra-mid hardness (DPH) of electrorefined vanadium are approximately equal to that of iodide crystal bar vanadium. The ductile-brittle transition temperature was found to be below 77° K, but with 0.175 weight-percent oxygen or 0.10 weight-percent nitrogen, it increased to between 123° and 190° K. With carbon content up to 0.11 weight-percent, the transition temperature remained below 77° K. The yield strength of the interstitial-containing alloys can be expressed by: au = 7.5 + 480 (pct N) + 290 (pct 0) + 280 (pct C), where au is the upper yield stress in 1,000 psi at 273° K. Profuse deformation twinning occurred in the alloys tested at 77° K. However, twinning could be suppressed by dissolved oxygen or nitrogen in excess of 0.15 and 0.086 weight-percent, respectively. Carbon, even though present in excess of the solubility limit, did not affect twinning.

Jan 1, 1965

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this con¬dition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By William W. Adams

Not since complete records of accidents first became available has the safety record of the quarrying and related industries of the United States been as favorable as it was in 1940. The combined accident-frequency rate was lower and therefore better than in any year since 1916, the first year for which complete and comparable figures are available. Although operating companies began to furnish accident reports to the Bureau of Mines in 1911, the reports for that year and the next few years were obviously incomplete as to number of accidents reported, especially slight injuries involving only 1 or 2 days of disability of the injured employees. By 1916 the reports from operating companies appeared to be reliable as to completeness of coverage of slight injuries. Although the number of men employed in 1940 was by no means a record, it represented a gain over each of the 2 preceding years. Likewise, the number of man-hours worked during 1940 was larger than in 1938 and 1939.

Jan 1, 1942