Search Documents

By K. K. Kelley, W. W. Weller

The heat capacities of four crystalline silicates of barium ( BaSiO3 , BaSiO4 , Ba Si¸0 , and BaSi₂0 ) and two crystalline silicates of strontium (SrSio and Sr₂Sio ) were measured over the temperature range from 51 ° to 298° K. The results were used to evaluate the entropies at 298.15 ° K. The entropy values were joined with known heats of formation to obtain the free energies of formation of the silicates with respect to their constituent oxides at 298.15 ° K.

Jan 1, 1964

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By Alexander May

This report describes a new method of weighing based upon observing the apparent weight of an object ill two separate pure gases. The method is presented in terms of experimental data which prove its soundness, but does not attempt to show the maximum accuracy possible with this technique. The new method incorporates the underlying principle that the apparent weight of an object is a linear function of the density of the atmosphere in which the object is weighed. The coefficients of this linear function are the true mass and volume of the object. From this functional relationship the true mass and volume of the object may be determined.

Jan 1, 1970

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By B. Z. Zhong, T. Ong, W. E. Wallace, W. Z. Whong, Z. W. Gu, M. J. Keane

"Abstract-Diesel emission particles (DEP) from an engine operating on the Federal Test Procedure VDC were dispersed in an aqueous mixture of dipalmitoyl lecithin (DPL). a major component of pulmonary surfactant and saline and were tested for genotoxicity using the unscheduled DNA synthesis (UDS) assay with autoradiography techniques in cultured Chinese hamster lung cells. A DEP sample from the same source was dispersed in dimethyl sulphoxide (DMSO) and subjected to the same assay. Both dispersions (in DPL and DMSO) were found to induce UDS in a dose-related manner. After separation of the sample into supernatant and sediment fractions. the activity of the DEP sample was found to reside in the supernatant fraction for the DMSO-dispersed sample; and in the sedimentary fraction for the surfactant-dispersed sample. These findings further indicate that genotoxic activity associated with DEP inhaled into the lung may become bioavailable through the dispersion properties of pulmonary surfactant components.INTRODUCTIONTHE mutagenicity of diesel emission particles (DEP) has been studied intensively (LEWTAS and WILLIAMS, 1986). Carcinogenic effects of diesel exhaust in exposed animals have been reviewed (NIOSH, 1988) and an evaluation of carcinogenic risks to humans from diesel engine exhausts has been published (IARC, 1989). Using components of pulmonary surfactant such as dipalmitoyl lecithin (D PL), dipalmitoyl phosphatidylethanolamine (DPPE) or dipalmitoyl phosphatidic acid (DPPA) dispersed in physiological saline, we have previously shown that diesel soots express mutagenic activities in the Salmonella histidine reversion assay system and in the sister chromatid exchange assay using the cultured Chinese hamster lung (V79) cells. Mutagenic activity of diesel soots dispersed in DPL, DPPE and DPPA was quantitatively comparable to and in some cases greater than, the activity expressed by an equal mass of soot extracted by dichloromethane-dimethyl sulphoxide (DCM-DMSO) (WALLACE et al., 1989).Unscheduled DNA synthesis (UDS) is accepted and frequently included, as one of the tests in the battery of assays used to assess carcinogenic-mutagenic potential -of chemicals (MITCHELL et al., 1983). In this study, induction of UDS in V79 cells by DEP, dispersed in the major component of pulmonary surfactant DPL, was carried out. The purpose of this study is to validate the suggestion generated from our previous work that mutagens associated with inhaled particles may be dispersed or solubilized in the phospholipid component of pulmonary surfactant and become active in such a phase (WALLACE er al., 1989) and to test the fractionated DEP sample using UDS assay for a more complete evaluation of its genotoxicity."

Dec 1, 1995

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By B. J. Moore

This publication contains analyses and related source data for 252 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1976 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Eighteen previous publications have presented the results of 11,065 gas analyses prior to 1976. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 15

Jan 1, 1977

By Sathit Tandanand

This Bureau of Mines report describes the method of obtaining a strength index for rock drillability, particularly for percussion drills. The original Protodyakonov method has been slightly modified, essentially to eliminate uncertainties in the measurement of the volume of fines, and to avoid conjecture in selecting the representative value as the strength coefficient. A theoretical consideration of the relevant parameters in the method was extended from a comminution theory, and hence the meaningful value was obtained experimentally by plotting the ratio of the number of drops and the volume of fines against the number of drops. The minimum ratio of the number of drops to the volume of fines in the plot was selected as the coefficient of rock strength. The modified method of obtaining the strength coefficient preserves the original Protodyakonov test apparatus and the merit of simplicity of the test procedure. The modified coefficient of rock strength shows its usefulness in predicting penetration rates with greater reliability than other mechanical properties. Consequently, the drillability curves were drawn using the modified coefficient of rock strength as the parameter for penetration rate prediction in the field.

Jan 1, 1975

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By C. L. Karr

U.S. Bureau of Mines (USBM) research has shown that fuzzy logic and genetic algorithms (GA's) have great potential for industrial process control. A technique has been developed by the USBM in which GA's are used to substantially reduce the time needed to design fuzzy logic controllers (FLC's).This technique shows promise as an efficient, robust approach to developing control systems. The research described in this report is twofold. First, the basic approach to developing an FLC using GA's is presented. The GA-designed FLC is developed for a specific physical system, a pH titration system. Second, empirical results are presented in which variations in the FLC implementation are compared. Specifically, the effects of altering five aspects of the pH FLC are considered: (1) membership function form, (2) number of fuzzy classes, (3) the center-of-area method, (4) implication operator, and (5) fuzzy rule form. Results indicate that (1) the technique in which GA's are used to design FLC's is effective, and (2) when this technique is used, variations in FLC implementation have little effect on FLC performance in a chosen control problem.

Jan 1, 2010

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980