Search Documents

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By John W. Nebgen

This report contains findings from a U.S. Bureau of Mines study concerning the inhibition of acid mine drainage formation from underground coal mines. A series of experiments was performed in which three different pyritic materials (wastes from coal production plants) were evaluated using several candidate inhibiting agents. Data obtained from the inhibitor-treated pyrites were compared with data from control experiments in which untreated pyritic wastes were used. The experiments were conducted by placing treated and untreated pyrite in columns, passing moist air through the columns to promote oxidation of pyrite, and washing the columns weekly to collect oxidation products for analysis. Experimental results indicate that quantities of acid mine drainage can be substantially reduced if soluble iron III (ferric) ion is controlled. The best inhibitors are neutral or alkaline siliceous materials such as fly ash, blast furnace slag, portland cement, and cement kiln dust. These materials appear to insolubilize iron III species to make them unavailable for reaction with pyrite. The data strongly suggest that the soluble ferric ion aqueous is a key oxidant for pyrite to produce acid mine drainage. The role of aqueous ferric ion as an oxidizing agent is substantiated further by data obtained using metallic iron (nails) as an inhibitor. The iron nails tended to keep the soluble iron in the iron 11 (ferrous) state. Experimental results indicate that sulfate and acidity levels are reduced when pyrite is in contact with the metallic iron.

Jan 1, 1979

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By W. P. Huleatt, Jr. Traver, Jr. Hazen

"Vanadium and uranium occur widely distributed throughout western Colorado and eastern Utah, and a few deposits have been found in northeastern Arizona and northwestern. New Mexico. The area in which it occurs includes approximately 10,000 square miles and is generally referred to as the vanadium region of Colorado and Utah.The majority of the deposits consist of replacement bodies and impregnations of rare minerals in the lower Morrison formation of Jurassic age. The ore bodies are flat, with irregular margins, and most of them conform to the stratification.The ""rim rock"" topography of the region includes many steep-walled canyons and plateaus, which afford an abundance of outcrops that have been responsible for most of the discoveries of mineralized areas. Delimitation of ore bodies within the areas is accomplished most effectively by core drilling from the surface.The deposits were discovered in 1899 and from 1911 to 1923 wore worked extensively for radioactive uranium ores, principally carnotite.The discovery and marketing of the richer and more cheaply mined pitch-blende ores of the Belgian Congo left the Colorado-Utah deposits without economic importance as sources of radium and uranium, and the region became inactive in 1923. After a period of comparative inactivity, the rising demand of the alloy-steel industry for vanadium renewed interest in the deposits, which were known to contain that metal. By 1938, vanadium production in the area had achieved respectable proportions, and new impetus was given to it by the United States’ entry into World War II in December 1941. In 1942, new treatment plants for vanadium ores were completed in Monticello, Utah, and Durango, Colo. In order to meet the requirements of these and other plants in the region, it became necessary to open new vanadium mines and prepare old onus for production.In an effort to stimulate mining, the Metals Reserve Company initiated a stock-piling program and appointed the united states Vanadium Corporation, to act as its purchasing agent.The extra production was expected to come largely from small, independent operators whose limited funds did not permit them to maintain development and exploratory programs. Study of conditions made it apparent that extensive exploration would be necessary to sustain production, and accordingly the Bureau of Mines initiated an exploratory drilling project on a cooperative basis with the Geological Survey. The principal objects of the work were to enlarge the known ore reserves of the area and, if possible, discover new ones. The results have been gratifying in both respects."

Sep 1, 1946

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

Research 82 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, D.C. 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1982

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By Scott Turner

The present rapid growth of coal stripping in the United States is a curious reversal of the tendency of mining to proceed from outcrop to depth. A combination of technical and economic factors bas stimulated the use of stripping methods until today many million tons of coal We being recovered by open cuts from sites that an earlier generation of engineers would have passed by as not commercially mineable or, if workable at all, only by underground methods. The total quantity of bituminous coal and lignite mined in the United States by stripping in 1928, the latest year for which detailed figures are available, was 19,789,000 short tons. Of this, 71,000 tons came from small workings not equipped with power shovels and 587,000 tons from properties in which stripping and underground work were carried on at the same mine; but as neither of these types is representative of modern stripping practice, they will be omitted in the discussion that follows. The total from strip pits proper in 1928 was 19,131,000 tons, produced by 176 pits employing 385 steam or electric shovels.3 Figures by States are given in Table 1. Detailed statistics will be found in Economics of Strip Coal Mining; a study by O. E. Kiessling, to be published by the United States Bureau of Mines.

Jan 1, 1930