Search Documents

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

By P. T. Brooks

Semipilot scale tests were made to demonstrate a newly developed electrorefining process which could be extrapolated to commercial scale in producing high-purity nickel and cobalt from crude nickel metal and high-grade ferronickel. The new process comprises application of solvent extraction techniques to remove and separate cobalt and iron from nickel and the electrodeposition in diaphragm cells of pure nickel and cobalt from chloride-based purified electrolyte. Using water insoluble organic amines, the solvent extraction operations enabled production of commercial-sized nickel and cobalt cathodes of higher purity than that of commercial electrolytic metals. The solvent extraction operation for separation of cobalt from nickel was made simpler than the conventional method. Furthermore, the solvent. extraction operation for iron removal made possible the electrorefining of ferronickel without the prohibitive loss of nickel resulting from the method ordinarily used for iron removal.

Jan 1, 1970

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

Introduction The NIOSH Office of Mining and Construction Safety and Health Research has redesigned its Mining Safety and Health Web topic page. The updated page incorporates a significant amount of new safety and health information, plus an improved layout to better serve stakeholder needs. It also provides back-ground information about the NIOSH Mining Research Program, including research awards, core competencies, unique labs, community and educational outreach, and a brief discussion of how the research program is structured. The new Web topic page can be found at www.cdc.gov/niosh/mining. "Search" Feature The redesigned Web topic page features improved search capabilities. The "Search Mining" feature on each page lets you search only the NIOSH Mining Safety and Health Web topic page. The user can still search the entire NIOSH Web page by using the "Search NIOSH" option. New Safety and Health Topics Developers expanded the "Safety and Health Topics" and reorganized the site to make it easier to find information. Each topic link now has a significant amount of new and updated information, as well as links to related topics of interest. Safety and health topics include dusts, diesel exhaust, hearing loss, contact with electric current, fires, explosives, ventilation, emergency management, new and older workers, and education and training. All topics can be accessed from the home page (Figure 1). Publications Although the Web topic page highlights many of the most requested publications on the safety and health topic links, you can find a complete list of downloadable publications as well. More than 600 mine safety and health publications are now downloadable from the page. Short summaries let the user quickly identify publications of interest. Products The updated Web topic page offers more than 120 NIOSH mine safety and health products, including training exercises, toolbox talks, videos, computer software, guides, and checklists, many of which are downloadable. If not, instructions are given on how to obtain copies. Some of our products include: • Software to analyze horizontal stress, design pillars for longwall mines, and select roof bolts for ground control. • Educational software including the Hearing Loss Simulator, which simulates the effects of noise and aging; and Coal Country, which teaches children about coal formation, mining techniques, and everyday uses of coal. • Utility software including the HazCom Helper software to assist individuals in writing a HazCOM plan, as required by the Mine Safety and Health Administration (MSHA), to track hazardous chemicals at their mine sites. • Guides for troubleshooting roof support systems, under-ground workstation design, and seating design. • Training exercises and videos that can be used for safety training. Data and Statistics General mining statistics are used by a wide variety of stakeholders. The NIOSH Mining Web topic page offers statistical graphs, tables, maps, fact sheets, and other publications that document the mining population, injuries, fatalities, diseases, and occupational exposures for all mining commodities. If users prefer to analyze data themselves, downloadable files of MSHA data are available. These cover employment, production, injuries, fatalities, and accident data from 1983 to the present and are available in both SPSS® and dBASE® formats.

Jan 11, 2005

By H. Winkelmann

The author, who himself has worked inn the field with various types of torsion balances, expresses in the article his experience with the recently marketed Haff-Torsion-Balance. The advantages of practical work with Haff?s s torsion balance as compared with other types are mentioned. In spite of low weight and corresponding small dimensions (Model M = 23.5 kg., Model Al = 11.5 kg.) the sensitiveness is not less than that in the largest instruments. It is at 1.10-9, which is proved by calculations. A comparison with the corresponding values of other types of torsion balances (Eötvös, Askania, Gepege) is given. The mechanical features of the instrument are briefly described, and the balance is illustrated by a, cross section of it. -- W. Ayvazoglou. DETERMINATION OF THE ELEMENTS OF THE MAGNETIC AND GRAVITATIONAL FIELDS INDUCED BY AN INFINITELY LONG HOMOGENEOUS CYLINDER By G. A. Gamburzeff Gerlands Beiträge zur Geophysik, Band 19, Heft 2/3 Leipzig, 1928, pp. 210-230. The present work is a. contribution to the quastion of the reason for the magnetic and gravitational anomalies in the government of Kursk (Russia).

Jan 1, 1929

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

By H. M. Urban

This paper, one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of mining at various mica mines in the United States, describes the methods now in use in the principal mica mines of the Southern Appalachian States. Those papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By D. R. Babich, E. R. Bauer

US. National Institute for Occupational .Safety and Health (NIOSH) researchers are conducting a Cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently sun eyed. The sound levels of milling and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This article presents the results o f the noise research conducted in both underground and surface limestone manes, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By D. R. Hanson

This Bureau of Mines study examines the acoustic vibrational spectra of rock slabs in the range of 0 to 5,000 Hz. The power spectra of so-called drummy rocks were found to be diagnostically enhanced in the range of 200 to 1,000 Hz. Comparison of the power in this band with that in a band from 3,000 to 3,500 Hz provides a quantitative measure of rock stability. A prototype field instrument was designed, constructed, and field-tested. This battery-powered instrument computes the power contained in the two frequency bands mentioned, compares the magnitude of these two quantities, and displays a number that is related to the detachment of the block tested. Field tests show that this instrument is capable of giving reliable measurements of block stability under conditions of noise and dust that would seriously degrade the accuracy of normal sounding techniques.

Jan 1, 1985

By W. H. Tomlinson

Although the thoughts and efforts of the great majority of people in many parts of the world are today directed toward killing each other, the purpose of this paper is to discuss means of conserving human life. In a world of turmoil and strife, we find time to discuss and make plans to achieve our objective -prevention of the "sacrifice" of life through avoidable accidents. The word" sacrifice" is used here advisedly, as one meaning of the word given in the 1942 edition of Funk and Wagnalls New Dictionary of the English Language is "the act of giving up some desired or valued object for the sake of *** future good." As everyone agrees that life is man's most priceless possession, one wonders if past sacrifices have been in vain. It appears that life is cheap in America; it is cheap because some of the industrialists are too much concerned with making a profit to devote much time and thought to conserving human life; it is cheap because some labor leaders apparently are interested solely in personal power and prestige; it is cheap because a great many workmen fail or refuse to cooperate energetically with the various organizations interested ill; their safety and welfare; it is of little value because, individually and collectively, we are indifferent to our responsibilities toward our fellow men.

Jan 1, 1944

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By Synthia N. McIntosh

The U.S. Bureau of Mines investigated the feasibility of using ammonium carbamate (NH2CO2NH4) leaching to recover manganese from steel plant slag. This investigation showed that treatment of the slag in hydrogen prior to leaching enhanced manganese extraction. Up to 80 pct of the manganese and 50 pct of the iron could be extracted from a silicon steel slag that had been pretreated in hydrogen at 700° C. Two 4-h leaching stages conducted at ambient temperature with a solution containing ammonia and carbon dioxide dissolved manganese and iron as their carbamate complexes. Heating the pregnant solution to 65° to 85° C decomposed the complexes and precipitated the metals as insoluble carbonate salts. Ammonium carbamate leaching of other slags from several steelmaking plants produced lower manganese extractions, which suggests that the method cannot be applied satisfactorily to all steelmaking slags

Jan 1, 2010