Search Documents

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of El Salvador has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . Under the terms of the Code of Commerce ( arts . 12ff . ) , foreigners living in El Salvador can engage in business on the same terms as nationals . This involves ( = $434.00 ) - except for those with a working capital , of less than a thousand pesos inscription in the merchants ' register , which can be refused only in case of manifest disability of a permanent nature .

Sep 1, 1930

By Doug Scott

Develop tools that companies can use to comply with 29 CFR 1910.1200.

By E. C. Tarpley

The Federal Bureau of Mines has studied solvent extraction as a means of concentrating the mineral components in coal. Solubilities of a number of American coals were determined using abietic acid as a solvent. The effect of rank on solubility was investigated, and maximum solubility was found with coals of intermediate rank. Vitrinite is the most soluble petrographic component; fusinite, micrinitc, and exinite are nearly insoluble. Spore exines also have a low solubility. Abietic acid is a hydrogen donor and reduces pyrite to ferrous sulfide. Mild hydrogenation of high-molecular-weight fragments of the coal structure to those of lower molecular-weight probably contributes to the solvent action. Even where solubility of the coal substance exceeds 90 percent, contamination of the mineral matter with coal makes identification of the mineral components difficult. Further separation might be possible by the application of float and sink techniques to the residue. INTRODUCTION Work n the solvent extraction of coal is conducted to recover commercially useful products and to characterize coal;. and obtain information on their structure. Some coals, particularly those of low rank, contain waxes, resins, and humic acids which can be removed by solvent extraction and find varied industrial uses. In World War II, solvent extraction of coal was conducted on a commercial scale in Germany to obtain a low-ash feed material for hydrogenation and to produce electrodes carbon for the aluminum industry.4 5/

Jan 1, 1960

By Doris M. Hyde

Mineral industry activity in many of the smaller Caribbean Island countries has remained minimal. For this reason, specific references to Bermuda, Guadeloupe, Martinique, and the Netherlands Antilles have been removed from textual and trade table presentations. Any significant future developments will be reported as they occur. Readers are referred to earlier Minerals Yearbook editions for previous information. Table 1 production statistics have been modified in some instances. References to certain nonmetal commodities were eliminated because information has often been unreliable. Their inclusion in table 1 was not considered important to either an overview of the area or to compatibility with volume I of the Minerals Yearbook.

Jan 1, 1984

By G. S. Scott, G. W. Jones

Trichloroethylene (CHC1CC12) is an important solvent for fats , resins , bitumens, rubber , sulfur , and phosphorus . It is used extensively in drycleaning because of its low order of combustibility and has recently been proposed as an inhalation anaesthetic . Its physical properties have been described by Carlisle and Levine . It is usually considered a noninflammable material ; however , substances that are noninflammable when mixed with air are not necessarily noninflammable when mixed with oxygen . Thus , Hewer's statement that " Trichloroethylene*** is not inflammable under any circumstances , nor will its vapor explode when mixed in any proportion with air , oxygen, or nitrous oxide , " requires qualification , especially in anesthesia, where pure oxygen may at times be substituted for air , This report gives the results of tests made to determine the inflammability of trichloroethylene in various mixtures of oxygen and nitrogen . The trichloroethylene used was Eastman's No. 1300. The boiling point was given as 86 ° to 87 °C . The specific gravity and refractive index of the sample measured in this laboratory were , respectively, 1.45 and 1.4759 at 25 °C .

Nov 1, 1942

By Roger J. Morrell

Disk-cutter experiments were performed on five rock types ranging in compressive strength from 9,000 psi to 27,000 psi. A specially constructed testing machine called a linear-cutter apparatus (LCA) was designed to load and traverse a free-rolling disk cutter across a sawed rock surface. The LCA was instrumented to measure the vertical and horizontal forces acting on the cutter during the run.. The ability of disk cutters to fragment rock was determined for both 60--degree and 90-degree cutting-edge angles, and relationships and regression equations were developed to predict cutter performance based on rock physical properties and applied forces,

Jan 1, 1970

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By K. K. Kelley

This report contains heat-content values for hexagonal crystalline germanium dioxide between 298.15° and 1,350° K., and for germanium dioxide glass between 298.15° and 1,800° K. experimentally determined by the Federal Bureau of Mines. No similar data for these substances are to be found in the literature. The heat-content and corresponding entropy-increment data are presented both in tabular form and by equations. Free energy of formation values are estimated for germanium dioxide glass at 298.15° and 1,800° K.

Jan 1, 1961

By Eric E. Ungar

Some fundamental facts regarding noise are summarized. Guidelines for reducing plant noise are indicated, and simple means are discussed for determining, whether quieting of specific equipment items will reduce plant noise significantly. Design and installation recommendations are made for quieting chutes by means of dams, impact cushioning pads, impact shields, and damping materials, and for quieting; screens by means of resilient decks, lined screen bottoms, drive mechanism enclosures, and side plate additions. A brief account is appended of the wear and productivity performance of resilient materials observed in three cleaning plants.

Jan 1, 1976

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By Virgil J. Stachura

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine that resulted in smoother highwalls. The 17; were smoother due to reduced overbreak and inherently safer A, to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delays, which changed the effective delay pattern geometry and the direction of burden movement. The blast delays in the highwall holes were 50 to 100 ms longer than the mine's nominal design pattern (flat V, 17- by 42-ms surface delays, 200-ms in-the-hole delay). The burden movement was effectively changed from a 45* angle to 90* with respect to the highwall. The results of the blast delay changes were evaluated using terrestrial photogrammetry to generate vertical profiles at regular intervals. This evaluation showed that delay changes produced generally smoother vertical profiles.

Jan 1, 1984

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950