Search Documents

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

Improve the dust-control effectiveness of the Rotoclone1 dry-dust collection systems used on surface coal mine drills.

Jan 1, 1994

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By Industrial Research Office

"The U.S. Bureau of Mines established on August 15, 1983, the Generic Mineral Technology Center for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. The Center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . ."" The Center's program is designed to permit an accelerated attack on the fundamental research problems for the control of respirable dust in mines.The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. The Generic Technology Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated. The Center activities involve the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications' in the respirable dust area.The Center is composed of faculty from the four universities/institutes listed above. The personnel, facilities and equipment that are available to the Center from these entities are diverse, complementary and comprehensive. More than fifty scientists, engineers; and medical personnel in the Center are engaged in respirable dust research. Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease Studies are available as a result of the existing relationship between NIOSH and West Virginia University.The breakdown of the dust research program into the five areas mentioned above recognizes the importance of an integrated fundamental research approach to the respirable dust problem compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities. The specific projects in the research areas are a result of a careful evaluation of the past and ongoing research activities, the identification of areas where data and information are scarce, and awareness of the recommendation of the National Academy of Sciences Study on the Measurement and Control of Respirable Dust. Penn State is the administrative unit for the Center. Funding to date is nearly $6.5 million."

Aug 31, 1989

By M. J. Brnich

The purpose of this US. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction derivered on either the Draeger QXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the doming task transferred.

Jan 1, 1992

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By L. E. Schultze

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines devised a processing sequence for recovering uranium from carbonaceous ores. Uranium extractions of 97 pct were obtained by contacting the ore with a solution containing 400 grams of ferric sulfate hydrate in 200 ml water for 3 hr at boiling temperature (96° C). Uranium was recovered from the leaching solution by solvent extraction with tri-issooctyl amine. The barren ferric sulfate solution was recycled to the leaching system. The leaching process resulted in no detectable dissolution of carbonaceous material from the ore. Work on the project was terminated in 1978 because of a transfer of responsibility to the U.S. Department of Energy.

Jan 1, 1981

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

Provide room-and-pillar operators with practical in- formation and guidelines concerning multiple-seam mine design to reduce ground problems associated with the interaction of adjacent working.

Jan 1, 1994

Track and control the tram maneuvers of continuous mining machines by developing and evaluating a laser sensor system. Background Progressive technology has the potential to greatly improve mine-worker safety, helping to create a safer, better working environment for mine workers by keeping them away from the dangerous face area. To benefit from such technology, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A cornerstone for computer-assisted operation is an effective guidance system. Since there are no guidance systems on any commercial continuous miners (CM's), the Bureau it-self developed and tested a laser-based sensor system, based on a commercial sensor called Lasernet. The laser-based guidance system employs four laser scanning sensors at fixed locations in a mine entryway to report the angular coordinates of two cylindrical retro-reflective targets mounted on a CM. Using triangulation, a real-time microcomputer system processes the sensor data and updates the xy position and heading (h) of the CM five times per second. Using a simple control algorithm and communications interface to the CM control computer, the system also controls rotational and translational tram maneuvers.

Jan 1, 1992

By F. J. Gallagher

The purpose of this circular is to present information on the construction and use of reinforced rubber-jacketed tubing and insulating air-line couplings in coal mines where Airdox is used for breaking coal in order to eliminate, insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.

Sep 1, 1949

By A. B. Cecala

A new prototype bag nozzle system has been designed under a Bureau of Mines contract to reduce dust generated during the bagging operation on fluidized air baggers. A field analysis of the new system has shown that the bag operator's dust exposure was reduced 83 pet. The amount of blowback was reduced 89 pet, which corresponds to a significant product savings. The new prototype system has been operating for a substantial period of time with no major problems.

Jan 1, 1984

By Robert P. Vinson

A sequential sampler, based on the Archimedes screw, has been developed by the Bureau of Mines. Its initial purpose was to collect air samples during tracer gas studies in underground mines. However, the basic concept can be applied to other sampling needs, including sampling of liquids. A prototype was built and successfully tested in the Bureau's Experimental Mine at Bruceton, Pa. The simple design makes the sampler inherently durable and low in cost.

Jan 1, 1976

"While control of dust-related diseases, the objective of the Generic Mineral Technology Center for Respirable Dust, is of prime importance from the human standpoint it is also essential to the economic well-being of the mining industry (FIGURE 23). Although significant progress has been made, the problem continues to be a major concern to the mining community. An increasing global demand for coal and other minerals means that production and the number of miners employed is on the rise. Therefore, the importance of this research to the mining industry cannot be overemphasized.The five areas of dust research are 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. Some experimental projects where the research is conducted almost exclusively in the laboratory may still rely on industry for imput. No industrial resources are necessary to the research of the non-experimental projects, for example computer modeling .The remaining research is classified as experimental and these projects do require interaction with industry in varying degrees. Periodic trips to mining sites in Western Pennsylvania, Southern Ohio, and West Virginia are necessary to record measurements or collect samples. Or companies may provide needed samples or equipment to the university for use in the laboratory. On several projects interaction is limited to advice or information supplied to the researcher by industry personnel."

Aug 31, 1989

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

Predict the spontaneous combustion potential of a mining operation using an expert system computer program.

Jan 1, 1994