Search Documents

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By Wilson Blake

The Bureau of Mines used a mathematical model based on the finite element method of stress analysis to calculate stresses and displacements surrounding an open pit mine in a gravity-loaded rock mass. Comparison of the finite element solution for a semicircular notch in a gravity-loaded plate with the theoretical solution for a semicircular notch in a plate under uniform compression parallel to the free boundary demonstrates the inapplicability of the latter method to openings at the free surface of a gravity-loaded medium. High stress concentrations are formed at irregularities along the boundary of an open pit in a gravity-loaded continuous competent rock; however, for this type of rock the magnitudes of the stresses are too low to be considered a major factor in open pit slope stability. High stress magnitudes will occur if, in addition to the gravity stress field, a large horizontal stress field exists.

Jan 1, 1967

By John H. Soulé

"INTRODUCTION The property of the Silver Spot Mines Co. is in the Boston Hill area within and adjacent to the southwest corner of Silver City, N. Mex. The area was visited by Bureau of Mines engineers 3/ in 1941 and 1942 during the investigation of possible sources of manganese. The area was visited again in November 1944 4/ to study the possibilities of geophysical exploration of the manganiferous-iron deposits. This geophysical work was performed in 1945 5/, confirmed the existence of known deposits of manganiferous-iron ores, and indicated the probable extent and situation of others.The Silver Spot property was churn-drilled from 1926 to 1929 during exploration for manganiferous-iron ores. The sludges from a number of the holes indicated low-grade lead-zinc mineralization. Lead and zinc minerals also were found on the dumps of some of the old shafts when the property was visited by D. H. Mullen, an engineer of the Bureau of Mines late in 1946. A diamond-drilling project was proposed. It was started in April 1947 with the intention of investigating the best of the known ore indications as shown by the old churn-drill holes and thus gathering new data upon which to base future work. Only one hole was drilled before the project was terminated because of lack of funds and time."

Mar 1, 1948

By C. I. Pierce

This report describes and presents results of a phase of a laboratory study conducted at the Morgantown Petroleum Research Laboratory, Federal Bureau of Mines, Morgantown, W. Va., to determine the response of shielded electrodes of different dimensions in thin, noninvaded beds and to stimulate interest in the use of focused-type logging devices in the Appalachian oilfields. A blotter model was used to obtain plots of the potential field in the vicinity of a model shielded electrode. Three plots are presented. The difference in curvature of equipotential lines and the variation in measured resistance values for different blotter-model conditions suggest that the shielded electrode will give resistivities higher than normal when measurements are taken in a thin conductive bed located between resistive beds, and resistivities lower than normal when measurements are taken in a thin resistive bed located between conductive beds.

Jan 1, 1961

By A. A. Berk

In the course of a study of the formation of external deposits on tubes in water-tube boilers it became desirable to determine the sulfur dioxide (SO2) and sulfur trioxide (SO3) in the Due gases. Determinations made by the A.S.M.E. method for SO2 and SO3 in gaseous products of combustion did not give accurate results. It was found that minute quantities of copper, present in the flue gases from the coal in use, caused oxidation of sulfite in the absorption bottle and that the carbon dioxide (CO2) in the flue gases caused high values for SO2. The A.S.M.E. test procedure was revised to prevent oxidation of sulfite in the absorption bottle and to allow for the effect of CO2; subsequent analyses of flue gases produced reliable results. The revised procedure is described.

Jan 1, 1950

By S. E. Khalafalla

The Bureau of Mines has used colloidal solutions of magnetite in a magnetic field to segregate nonmagnetic materials such as nonferrous scrap metals and to concentrate precious minerals. Conventional magnetic separation relies on the inherent magnetic susceptibility of the material to be separated and may be designated as magnetic separation of the first kind the medium of separation rather than the separated particles are made magnetizable, a new system of gravity separation results. In this new magnetic separation of the second kind, a magnetic fluid rather than air or water acts as the separation medium. The same force that attracts magnetic objects in separations of the first kind also attracts the entire separation medium in separations of the second kind, thereby creating a reactionary force of equal magnitude in the opposite direction. This force, sometimes called the levitation force, can be made to segregate nonmagnetic particles in a flowing stream according to their specific gravity. The technique has been applied to segregate nonferrous metals from automobile and appliance shredders and mixed scraps. The system has also been used to upgrade diamondiferous jig concentrates from certain river gravels in order to facilitate the sorting and recovery of their diamond content.

Jan 1, 1981

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

By Joseph V. Mather, E. H. McCleary

"INTRODUCTION Workmen are transported in shafts in various types of cages or skips, most of which were designed primarily for hoisting cars and materials. Therefore, in general the cages or skips are not completely enclosed, adequate and gates are not always provided, and at many mines signaling devices and telephones are re¬stricted to those at the various landings in the shafts.Shaft accidents are usually severe - frequently fatal - and as a rule such an accident is caused by failure to comply with company rules or by ignoring them.Sixty men were killed and 555 men were injured in shafts of the anthracite and bituminous coal mines of the United States during the 5-year period 1938-42. 4/ Many of these accidents could have been prevented by having properly enclosed cages and adequate locking devices on doors to prevent workmen from falling into the shafts.The officials of the Heidelberg Coal Co. contemplated utilizing an old coal-hoisting shaft as a man-hoisting shaft; however, it was their desire to avoid the use of the conventional cage and to try to provide a safer means of transporting men in the shaft. Investigations and studies made by the officials revealed that an elevator similar to those used in large buildings would be more economical in first cost, maintenance, and operating costs would be less, and it would be safer and more convenient for the workmen. Effective safety devices for such elevators have been developed to such a high degree that those properly installed seldom fail. The elevator or man cage finally chosen cannot be pulled above the top landing through mechanical or man failure; it stops automatically at each landing and cannot be moved while a door is open; when the cage leaves the landing the doors opening to the shaft are automatically locked by mechanical and electrically operated locks; electric lights, telephone communication, and push-bottom controls are available on the cage, and adequate safety switches and overspeed controls are provided."

Jun 1, 1947

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938

By H. S. Hardman, G. T. Adams, Will H. Goghill

"Usually a newly developed machine leaves the factory ""on a wing and a prayer."" The manufacturer hopes that the operator will hasten to report defects. In turn, when the suggestions arrive the manufacturer makes the required changes and maintains close collaboration with the operator. Thus the history of our machines of today is written.Laboratory concentration tables are exceptions to growth by experiment and collaboration. Their operation never enters directly into the cost sheet; they are seldom used for longer periods than 10 minutes; and the experimenter, while hurrying to another job, accepts the table, good or bad, for a quick test on his ore. Thus we go back about 50 years when we use the preset in factory-built laboratory table.The Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, recognized the existence of a tabling problem net usually considered. That is, instead of using the table to test the ore, the ore was used to test the table. In this critical examination of laboratory table six defects were encountered (and remedied). They are:"

Oct 1, 1945

By A. W. Ambrose

"Records of individual wells form the basis for the successful operation of any company engaged in the production of petroleum. The expense attached to the compilation of records is negligible in comparison with the benefits resulting from their use. There a company has not a complete system of records, immediate attention should be given to the preparation of forms upon which to collect data, and, to the collection of data for these forms. The records needed vary with each district, but for each field a set should be adopted that will best meet the needs of each property. Practically all operators, and particularly all successful operators, agree on the necessity of good records, shopping what the wells have done, are doing, and may be expected to do in the future. Any operator realizes the value of records of sales of oil and should place almost equal emphasis on the records of well logs and histories showing the east and present performances of wells. Indeed, trustworthy records are absolutely necessary for the proper operation of any oil or gas property.Complete records should be kept on each well from the time the location and elevation are determined until the well is abandoned, and the engineer should review old records often enough to be familiar with the past performance of the various wells and with the conditions that affect production. Some of the forms that may be prepared are:--"

Mar 1, 1920

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976

By Robert L. Thorne

As an integral part of the investigation of critical and essential minerals in Alaska , the Bureau of Mines examined the lead deposits in the Slana area . Four examinations were made during June , July, and August 1945 in the 200 - square -mile area immediately northwest of Slana . The settlement of Slana lies near the conflux of the small Slana River with the mighty Copper River less than 60 miles southwest of Tek Junction on the Alaska Highway . Travel through the area and the examination of the properties were conducted by a three-man crew consisting of the author , a caterpillar operator , and a laborer . An RD6 caterpillar , equipped with blade and winch , was used in breaking trail and freighting through the country . Supplies and equipment were loaded on a 7- by 14 -foot , double - end , go -devil , which was hauled by the tractor .

Nov 1, 1946

By Clark R. Neuharth

To assess the supply status of ultra-high-purity silicon for national defense needs, the U.S. Bureau of Mines conducted a general study of the availability of materials and processing technology for silicon used in the manufacture of infrared (IR) detectors from raw materials to the highly advanced device state. The United States possesses all of the raw materials and processing technology for IR detector-grade silicon production, but does not produce at all of the processing stages on a regular basis. Consequently, the United States continues to rely on foreign sources for some of these critical materials.

Jan 1, 1989

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

 Previous reports of this series/7/8/ presented data on the composi- tion of exhaust gases produced by Diesel engines operating under various conditions possible in underground workings. In all previous experiments, the engines tested were in proper mechanical condition; that is, they were adjusted and maintained in accordance with the manufacturer's instructions. In discussing the results of these tests in relation to the use of Diesel engines underground, the importance of maintaining engines in proper mechanical condition was emphasized, although no data were presented to indicate the effect of engine maladjustments on production of harmful and objectionable constituents of exhaust gas. It is the purpose of this report to present such data and to reemphasize the importance of adequate maintenance for Diesel engines used underground.

Apr 1, 1943

By Jr. Schnakenberg

The National Institute for Occupational Safety and Health (NIOSH) has been working with diesel emissions control technology and the underground mining industry for a number of years. Underground isolated zone studies provided the emissions reduction performance of all of the alternative technologies currently available. A NIOSH/MSHA guide is available which provides mines with information and a process for selecting diesel particulate filters (DPF). Recent NIOSH experience suggests that more attention may be needed in managing the issues associated with diesel emissions and their control. The author argues that a holistic approach is needed which involves several key mine operations departments or disciplines by positing that workplace air can be considered as the product of a complex manufacturing process and examining how that process could be managed.

By John R. Benham

The Long Swamp RARE II area contains no prospects, claims, or mines. It has a low potential for ore deposits. There are no geothermal, oil, or gas leases in the area. APPRAISAL There are no mining districts in the study area. The nearest is Chewack Mining District, which is 6 mi (9.6 km) north of the area. This district had numerous claims located for tungsten; the principal tungsten ore mineral was wolframite. Wolframite was found here in 1898 by surveyors of the International Boundary Commission. The area was staked in 1908 and developed during 1915 and 1916. Only in 1936 was ore shipped; the 30 ton (27.2 t) shipment proved to be unprofitable for the claimants (Culver, 1945, p. 41).

Jan 1, 1982

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By Alvin M. Cummings

"INTRODUCTION During July and August 1943, the Bureau of Mines undertook an investigation of the Trego lead-zinc mine, near the town of Platteville in Grart County, Wis. as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the nation's war program.The Bureau of Mines completed eight churn-drill holes and sampled mineralized faces in the mine workings to determine if further exploitation was justified in an area between the mine and a zone previously drilled to the east.Following the investigation described herein, intermittent operations were resumed. Except where otherwise stated, this report describes conditions only to the time of completion of the Bureau of Mines investigations.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation described in this report was conducted under the immediate supervision of the author and 0. W. Terry, mining engineer of the Bureau of Mines, with the assistance and advice of E. D. Gardner, re¬gional engineer, and E. P. Barrett, district engineer. Final data were prepared under the direction of Paul Zinner, acting chief, Minneapolis Branch, Mining Division.A. V. Heyl, Jr., and A. F. Agnew of the Federal Geological Survey cooperated with the Bureau's engineers and made lithologic studies required during the drilling program.The cooperation of W. N. Smith and O. E. DeWitt of the Vinegar Hill Zinc Co. and Francis Piquette of the Piquette Mining Co. facilitated the investigation to a great extent."

Mar 1, 1948