Search Documents

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By Launa G. Mallett, Robert H. Peters, Barbara Fotta

Due to variations in the thickness of U.S. coal seams, there is great variability in the height of the roof where underground miners work. Restrictions imposed by low seam heights have important safety consequences. As the height of their workplace decreases, miners must stoop, duck walk, or crawl, and their vision, posture, and mobility become increasingly restricted. Low seam height also places important restrictions on the design of mobile equipment and other mining machinery. Using the employment and injury data reported to the Mine Safety and Health Administration (MSHA) from 1990 to 19% small underground bituminous coal mines with less than 50 employees were stratified by average coal seam height according to the following categories: low (? 42"), medium (43"60N), and high (? 61"). Injury rates for both nonfatal days lost and fatality cases were examined by seam height and leading type of injury incidents. The leading types of Incidents associated with fatalities were roof falls and powered haulage equipment. In comparison to high-seam mines, miners working in low or medium seams are at higher risk of being killed by powered haulage equipment, roof bolting machines, and falls of unsupported roof. The leading types of incidents associated with nonfatal injuries were handling materials and powered haulage. As mining height decreases, miners are at increasingly higher risk of having a nonfatal injury from incidents involving roof bolting machines, load-haul-dump equipment, personnel carriers, and powered haulage conveyors. As mining height increases, miners are at increasingly higher risk of having a nonfatal injury from slips and falls and incidents involving shuttle cars and roof and rib falls. Knee injuries are a particularly severe problem in low- seam mines. The rate of injuries to miners while crawling or kneeling is 10 times higher in low seams than in high seams

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By T. R. Waters, F. Li, R. L. Huston

This paper describes the development of a multi-body biomechanical model that can be used to assess the risk of low back disorders due to occupational exposure to jarring and jolting from operation of heavy mobile equipment (e.g., trucks, haulers, graders, tractors, etc.) The four-element dynamic spinal model is capable of providing estimates of the force and acceleration responses of the head/neck, upper, lower, and middle torso resulting from vibration input collected in field studies. The paper also presents a method for using the model output to assess an individual's risk of low back disorder due to a specific jarring and jolting exposure.

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By Aarne Visnapuu

Pneumatic chipping, scaling, and grinding can expose the tool operator to noise levels in the range 90 to 120 dbA. In most chipping and scaling operations, casting resonance is the primary source of noise, followed by air exhaust, and machine and chisel resonance. In grinding, the air-exhaust noise predominates. The Bureau of Mines has shown that noise from these operations can be reduced by up to 15 dbA. Workpiece resonance was reduced by sand or other damping methods; tool resonance, by internal damping; and chisel resonance, by constrained-layer treatment. Mufflers reduced air-exhaust noise, and an acoustically treated booth was effective in containing noise around the work area without increasing operator exposure.

Jan 1, 1977

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

To monitor the quantity and quality of air in underground mines to assure safe working conditions. Approach Several mine air monitoring systems, consisting of sensing stations in the return airways and control stations on the surface, have been Installed and tested. How It Works Sensor stations are located at strategic places in the underground mine. At each station, the sensors measure air velocity, air temperature, methane concentration, and carbon monoxide concentration. In one system, differential air pressure between intake air and return air, is also measured. Output voltages of the sensors are converted to digital signals at the sensor stat ion; these signals are multiplexed so that data from all sensors can be trans-phone wire to a central station. There the data are displayed and alarms are triggered when the sensed values exceed (or in the case of air velocity, fall below) a preset value. In addition to receiving data automatically, the central station can poll individual sensors at any time.

Jan 1, 1978

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935